Instruction/ maintenance manual of the product FS526Tv2 NETGEAR
Go to page of 20
350 East Plumeria Drive San Jose, CA 95134 USA July 2013 202-1 1251-02 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Hardware Installation Guide.
2 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my .netgear .com .
3 Contents Chapter 1 Introduction and Hardware Description Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 1 1. Introduction and Hardware Description The NETGEAR® ProSAFE® 26-Port Fast Ethernet Smart Switch FS526Tv2 is a state-of-the-art, high-performance, IEEE-compliant network solution. T o simplify installation, the switch is shipped ready for use out of the box.
Introduction and Hardware Description 5 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Overview This hardware installation guide is for the NETGEAR ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2. The switch provides twenty-four 10/100BASE-T ports and two 10/100/1000BASE-T ports.
Introduction and Hardware Description 6 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Figure 1. Example of a network configuration Switch Features The following list identifies the key features of the switch: • T wenty-four RJ-45 10/100 Mbps Fast Ethernet switching ports.
Introduction and Hardware Description 7 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 • Active flow control to minimize packet loss and frame drops. • Half-duplex back-pressure control. • Per-port LEDs and system LEDs. • Internal power supply .
Introduction and Hardware Description 8 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer . Keep the carton, including the original packing materials, in case you need to return the product for repair .
Introduction and Hardware Description 9 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 LEDs The following table describes the LEDs. Product Label The product label on the back panel of the switch shows the hardware model number and version, the software version, the unique MAC address, and the unique serial number .
Introduction and Hardware Description 10 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 RJ-45 Ports RJ-45 ports are autosensing and autonegotiating ports. When you insert a cable into an RJ-45 port, the switch automatically ascertains the maximum speed (10, 100, or 1000 Mbps) and duplex mode (half- or full-duplex) of the attached device.
11 2 2. Installation This chapter describes how to install the switch, which involves the steps that are described in the following sections: • Step 1: Prepare the Site • Step 2: Install the Switc.
Installation 12 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Step 1: Prepare the Site Before you install the switch, ensure that the operating environment meets the requirements in that are described the following table.
Installation 13 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Install the Switch in a Rack T o install the switch in a rack, you need the 19-inch rack-mount kit that is supplied with switch. Note: T o prevent the rack from overbalancing and toppling over , install devices from the bottom of the rack to the top.
Installation 14 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Step 3: Check the Installation Before you apply power to the switch, do the following: • Inspect the equipment thoroughly . • V erify that all cables are installed correctly . • Check cable routing to make sure that cables are not damaged or creating a safety hazard.
Installation 15 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Step 5: Apply AC Power The switch does not have an On/Off switch. Y ou apply AC power to the switch by connecting the power cord, and you remove AC power from the switch by disconnecting the power cord.
16 3 3. T roubleshooting This chapter describes how you can troubleshoot the switch. The chapter covers the following topics: • T roubleshooting Chart • T roubleshooting Suggestions.
T roubleshooting 17 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 T roubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems. T able 3. T roubleshooting chart Symptom Cause Solution Power LED is off. No power is received.
T roubleshooting 18 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Configuration If problems occur after you alter the network configuration, restore the original connections and determine the problem by implementing the new changes, one step at a time.
19 A A. Physical and T echnical Specifications This appendix provides the physical and technical specifications for the switch. T able 4. Physical and technical specifications Feature Description Network protocols and supported standards • IEEE 802.
Physical and T echnical Specifications 20 ProSAFE 26-Port Fast Ethernet Smart Switch FS526Tv2 Environment • Operating temperature. 0 to 50°C (32 to 122°F) • Storage temperature. –20 to 70°C (28 to 158°F) • Operating humidity . 10–90% maximum relative humidity , noncondensing • Storage humidity .
An important point after buying a device NETGEAR FS526Tv2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NETGEAR FS526Tv2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NETGEAR FS526Tv2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NETGEAR FS526Tv2 you will learn all the available features of the product, as well as information on its operation. The information that you get NETGEAR FS526Tv2 will certainly help you make a decision on the purchase.
If you already are a holder of NETGEAR FS526Tv2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NETGEAR FS526Tv2.
However, one of the most important roles played by the user manual is to help in solving problems with NETGEAR FS526Tv2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NETGEAR FS526Tv2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
