Instruction/ maintenance manual of the product XT5000 NEC
Go to page of 46
MultiSync XT5000 High Light Output Pr ojection System User’ s Manual.
E – 2 CAUTION: To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. 3. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779.
E – 3 Fire and Shock Precautions 1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent potentially dangerous concentra- tions of ozone and the build-up of heat inside your projector. Allow at least 8 inches (20cm) of space between your projector and a wall.
E – 4 Recommandations importantes Ces instructions de s é curit é ont pour but d'assurer une longue vie à votre projecteur et d' é viter un incendie ou une d é charge é lectrique. Pri è re de les lire avec attention et de tenir compte de tous les avertissements.
E – 5 NEC Technologies, Inc.(hereafter NECTECH)warrants this prod- uct to be free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Parts and labor are warranted for (1) One Year from the date of the first customer purchase.
E – 6 T ABLE OF CONTENTS INTRODUCTION Introduction to the MultiSync XT5000 Projector ................... E – 7 Getting Started ...................................................................... E – 7 What's in the Box? .................
E – 7 INTRODUCTION This section introduces you to your new MultiSync XT5000 Projec- tor , provides a list of materials that comes with your projector and describes the features and controls.
E – 8 1. Part Names and Functions Stacking P ad (4 pcs) Digital Input T erminal P anel Remote Sensor PC Card Slot Inser t a flash memor y card here to upgrade the projector system software or cop y .
E – 9 LENS SHIFT ZOOM MENU SELECT - + ENTER ON INDICATOR POWER STATUS ON/OFF OFF CANCEL FOCUS Controls Remote sensor 11 10 9 8 7 5 4 2 1 3 6 1. Power Button Press to turn the projector on when the projector is in the standby condition (Main Power switch must be on and the PO WER indica- tor lit amber).
E – 10 Terminal Panel 1 INPUT3 RGB R/Cr G/Y B/Cb H/HV V R/Cr Cr Y G/Y B/Cb Cb H/HV V OPTION IN OUT REMOTE1 REMOTE2 INPUT7 INPUT8 INPUT5 S-VIDEO1 Y C S-VIDEO2 VIDEO1 VIDEO2 INPUT6 IN OUT INPUT2 INPUT.
E – 11 Push the left side of the panel to open the compartment for the RGB Digital connectors and the optional SDI board. Space to install the optional SDI board.
E – 12 OFF + - PICTURE ADJUST ABC DEF GHI JKL MNO PQR STU ,. UNDO CANCEL TEST PICTURE KEYSTONE AMPLITUDE ENTRYLIST SOUND OSD MUTE MAGNIFY HELP INFO. POSITION AUTO PIXEL VWX YZ? WHITE BAL.
E – 13 12 INFO Displays the "Source Information" or "Projector Information" win- dow . This button toggles between these tw o windows. 13 TEST Press to display the test pattern. Pressing this button sequentially selects nine test patterns.
E – 14 2. INST ALLA TION This section describes how to install the lens, set up the projector and how to connect video and audio sources. Hook Fixed pin Optional Lens Installation Four optional lenses are a vailable: TL-08SF , TL-1Z, TL-2Z and TL- 4Z.
E – 15 3) Rotate the lens barrel clockwise to fix the lens unit. Lens barrel 3. Secure the f ixed screws and connect the extension cable attached to the projector . 1) Secure the three screws on the lens holder . 2) Insert the connector of the lens unit into the socket of the ex- tension cable attached to the projector .
E – 16 Pulling Out the Handles Pull out the handle until it clicks into place. Retracting the Handles 1) Push the lev er to unlock and 2) retract the handle. Selecting A Location The further your projector is from the screen or wall, the lar ger the image.
E – 17 P ower cab le Stopper O F F P O W E R O N Attaching the Power Cable Stopper The Power cable stopper is pro vided with the projector so that the cable cannot be accidentally unplugged from the A C IN. 1) Remov e two screws. These scre ws are used later again.
E – 18 Screen Size and Pr ojection Distance 1. Place your projector on a flat level surf ace at the optimal distance from the screen. (A void having bright room lighting or sun light directly on the screen or projection surface.) 2. Connect the power cable, remov e the lens cap and turn the projec- tor on.
E – 19 Reflecting The Image Using a mirror to reflect your projector's image enables you to enjoy a much lar ger image in a much smaller space. Contact your dealer if you need a mirror .
E – 20 OUTPUT OUTPUT RGB DIGITAL INPUT9 INPUT 0 SDI OUTPUT OUTPUT RGB DIGITAL INPUT9 INPUT 0 SDI OUTPUT OUTPUT RGB DIGITAL INPUT9 INPUT 0 SDI OUTPUT OUTPUT INPUT9 INPUT9 DFP cable (supplied) DFP cab.
E – 21 3) Adjusting and r egistering signals to be projected in Link mode and stack application. Signal Data Preparation 3-1. Create data f or the master projector and cop y data to the slav e projectors. 3-1-1. Choose one projector as the master . 3-1-2.
E – 22 When used in standalone operation 3. CONNECTIONS INPUT3 RGB R/Cr G/Y B/Cb H/HV V R/Cr Cr Y G/Y B/Cb Cb H/HV V OPTION IN OUT REMOTE1 REMOTE2 INPUT7 INPUT8 INPUT5 S-VIDEO1 Y C S-VIDEO2 VIDEO1 V.
E – 23 INPUT3 RGB R/Cr G/Y B/Cb H/HV V R/Cr Cr Y G/Y B/Cb Cb H/HV V OPTION IN OUT REMOTE1 REMOTE2 INPUT7 INPUT8 INPUT5 S-VIDEO1 Y C S-VIDEO2 VIDEO1 VIDEO2 INPUT6 IN OUT INPUT2 INPUT1 INPUT4 When Used with One Switcher (ISS-6020/ISS-6020G) Up to 10 input signals can be accepted when the projector is connected to one Switcher .
E – 24 When Used with Two or More Switchers (100 Inputs) Up to 100 inputs can be accepted using the NEC ISS-6020 Switcher . How to make connections: 1 Connect the REMOTE 1 terminal of the master Switcher to the REMO TE 1 of the projector using the optional control cable (15p- 15p/CTL-6010).
E – 25 Set the DIP switch (S8601) of the Switcher as follows: The Projector Slot 1 of the Master Slot 2 of the Master Slot 3 of the Master Slot 4 of the Master Slot 5 of the Master Slot 6 of the Mas.
E – 26 REMOTE 1 Connector This connector is used for either connecting the ISS-6020/ISS-6020G Switcher or a third party external control device. When the Switcher is used, connect it with the optional control cable (15-15 pin; 50 ft./16m; CTL-6010) to this connector.
E – 27 When used in stand alone operation. Pin No. 14 5 10 4,8,12,11 SHORT/OPEN SHORT OPEN SHORT OPEN SHORT OPEN FUNCTION External control mode ON External control mode OFF POWER ON POWER OFF PICTUR.
E – 28 Operating Multiple Pr ojector with Remote Control Y ou can operate multiple projectors with the same remote control in wireless operation. T o do so: 1. Select [Main Menu] → [Projector Options] → [Setup] → [Page 3] → [Projector ID] and assign an ID number to each projector .
E – 29 4. OPERA TION This section describes how to select a computer or video source, ad- just the picture and sound, edit a signal and adjust all other settings and adjustments for proper projector set-up. General Controls Before you turn on the projector ensure that the computer or video source is turned on and that the lens cap is remov ed.
E – 30 A List of Direct Key Combinations CTL+ INPUT (1-10) Switches to any selected signal found in the Entry List. T o enable this combination, you must first assign specif ic remote keys for direct input selection in the Entry Edit windo w . CTL+ ENTER (While displaying Entry list) Displays the Entry Edit Command windo w .
E – 31 Source Select Adjustments Image Options Projector Options PC Card Files Help Test Pattern RGB 1 RGB 2 RGB 3 Component (YCrCb) Video 1 Video 2 S-Video 1 S-Video 2 more Brightness Contrast Colo.
E – 32 Menu Elements Highlight Solid triangle Title bar Ta b Cancel Button OK Button Check bo x Slide bar Radio button Menu windows or dialog box typically have the following elements: Title bar: Indicates the menu title. Highlight: Indicates the selected menu or item.
E – 33 Menu Descriptions & Functions Source Select Enables you to select a video source such as a VCR, D VD player , laser disc player , computer or document camera depending on what is connected to your inputs. Press the up/do wn buttons on your remote control or the projector cabinet to highlight the menu for the item you want to adjust.
E – 34 Adjustments The Adjustments Menu pro vides access to controls for your image. Use the ▲ / ▼ buttons on your remote control or the projector cabinet to highlight the menu for the item you want to adjust. Picture Brightness: Adjusts the brightness le vel or the back raster inten- sity .
E – 35 V ideo F ilter This feature reduces video noise. Select the appropriate filter for your signal. Bar 0 ..................... Of f Bar 1/3 .................. High Bar 2/3 .................. Medium Bar full ................. Lo w Color T emperature This feature adjusts the color temperature using the slide bar .
E – 36 Factory Default Returns all adjustments and settings to the factory preset level. All Data: Resets all adjustments and settings for all the signals to the factory preset. Including Entry List : Also deletes all the signals in the Entry List and returns to the factory preset.
E – 37 Select one of the follo wing three levels for reducing video noise. Lo w , Medium or High. NO TE: The lo wer the Noise Reduction le vel, the better the image quality . Increasing Noise Reduction lo wers video bandwidth. Color Matrix Noise Reduction First, select an appropriate color matrix for your input signal, either HDTV or SDTV .
E – 38 Allows you to set preferences for the on-screen menu. Language: Y ou can choose one of se ven languages for on-screen instructions. The options are: English, German, French, Italian, Spanish, Swed- ish and Japanese.
E – 39 Setup Enables you to set operating options. Select “ OK ” to sav e your changes for all the features of Page1, Page2, Page3 and P age 4. <Page 1> Orientation: This orients the screen image to match the physical orientation of the projector .
E – 40 Communication/P ort: Not used. Speed: This feature sets baud rate of the OPTION IN (D-Sub 9 pin) con- nector from 4800 to 38400 bps. The default is 38400 bps.
E – 41 PC Card Files Displays a list of all the f iles stored in the PC card so that you can select a file you w ant to display . Y ou can also sort files by f ile name or date, or display the file. Although a list of all the files in the PC card is displayed, you can vie w files in text, HTML, JPEG and BMP format only .
E – 42 Optical Panel * 1 DMD TM .9" x 3 1024 x 768 nativ e resolution up to 1280 x 1024 with advanced AccuBlend TM T echnology Lamp 1.0kW Bubb le T ype Shor t Arc Xenon Built in: Overheat Prote.
E – 43 Acceptable Sync Sys Separate Sync/Composite Sync/ Sync on Green Memory 100 individual memory locations Menu System Pull down m ultilingual on-screen display English/Ger man/F rench/Italian/Sp.
E – 44 6. Optional Accessories Lens TL-08SF (Short Focal Lens 0.84) TL-1Z (Zoom Lens 1.5 - 2.5:1) TL-2Z (Zoom Lens 2.5 - 4.0:1) TL-4Z (Zoom Lens 4.0 - 7.0:1) Cable XT D-CABLE 5M (DFP cable) Interface Board XT SDI BOARD Ceiling Mount Kit XT CMKIT Switcher ISS-6020 Video/RGB Switcher Link Mode: Compatible Input Signal List (Expert mode only) 7.
E – 45 8. Menu (Expert mode) Digital Link Analog Link Source Select L L Adjustments Picture (all items) L L Blanking L L Image Auto Adjust N M Position L L Pixel Adjust L M Resolution L L Video Filter L L Color T emperatur e L L White Balance L L Switcher N N Keystone L L Ref.
E – 46 Appendix 506 (19.92) 326 (12.83) 174 (6.85) 682 (26.85) 35.5 (1.40) 308 (12.13) 30 (1.18) 54 (2.13) Dimensions The drawings do not include the lens part.
An important point after buying a device NEC XT5000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NEC XT5000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NEC XT5000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NEC XT5000 you will learn all the available features of the product, as well as information on its operation. The information that you get NEC XT5000 will certainly help you make a decision on the purchase.
If you already are a holder of NEC XT5000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NEC XT5000.
However, one of the most important roles played by the user manual is to help in solving problems with NEC XT5000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NEC XT5000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
