Instruction/ maintenance manual of the product MT1040 NEC
Go to page of 42
MultiSync MT840/MT1040/MT1045 LCD Pr ojector User’ s Manual English.
E–2 IMPOR T ANT INFORMA TION Precautions Please read this manual carefully before using your NEC MultiSync MT840/MT1040/MT1045 Projector and keep the manual handy f or future reference . Y our serial number is located under the name plate label on the left side of your MultiSync MT840/MT1040/ MT1045.
E–3 Important Safeguards These saf ety instructions are to ensure the long lif e of your projector and to pre vent fire and shoc k. Please read them carefully and heed all warnings. Installation 1. For best results, use your projector in a darkened room.
E–4 Lamp Replacement • T o replace the lamp , f ollow all instr uctions pro vided on page E-33. • Be sure to replace the lamp when the Status light comes on. If you continue to use the lamp after 2000 hours (1500 hours : MT1045) of use, the lamp bulb ma y shatter , and pieces of glass ma y be scattered in the lamp case.
E–5 T ABLE OF CONTENTS 1. INTRODUCTION Introduction to the MultiSync MT840/MT1040/MT1045 Projector ... E-6 Getting Star ted ............................................................ E-6 Getting to Kno w Y our MultiSync MT840/MT1040/MT1045 Projector .
E–6 1. INTRODUCTION Introduction to the MultiSync MT840/MT1040/MT1045 Projector This section introduces you to your new MultiSync MT840 (SV GA)/ MT1040 and MT1045 (XGA) Projector describes the features and controls.
E–7 M E N U E N T E R C A N C E L SELECT POWER STATUS ON / OFF SOURCE AUTO ADJUST USB AC IN Getting to Know Y our MultiSync MT840/MT1040/MT1045 Projector Front Features M E N U E N T E R C A N C E L.
E–8 T op Features 1 Source Button Use this button to select a video source such as a PC, VCR, DVD player or PC Card V iewer (PC card installed). 2 Auto Adjust Button Use this button to adjust Position-H/V and Pixel Clock/Phase for an optimal picture.
E–9 USB PC CONTROL REMOTE CONTROL INPUT MOUSE OUT S-VIDEO VIDEO AUDIO RGB INPUT 2 AUDIO RGB INPUT 1 L / MONO R T erminal Panel Features 1 8 6 5 10 12 11 1 USB (Mouse) T erminal Connect a commercially av ailable mouse that supports USB. Y ou can operate the menu or V iewer with the USB mouse via this terminal.
E–10 Remote Control Features NO TE: If you ar e using a Macintosh computer , you can click either the right or left button to activate the mouse . 1 Source Button Press to select a video source. 2 Auto Adjust Button Use this button to adjust Position-H/V and Pix el Clock/Phase for an optimal picture.
E–11 9 Picture Mute Button This b utton turns off the image and sound for a short period of time. Press again to restore the image and sound. 10 Help Button Provides information about operation and adjustment procedures or the set information for the current menu or adjustment during menu operation.
E–12 2. INST ALLA TION This section describes how to set up your MultiSync MT840/MT1040/ MT1045 projector and how to connect video and audio sources. Setting up Y our Projector Y our MultiSync MT840/MT1040/MT1045 Projector is simple to set up and use.
E–13 D H V Screen (inch) Throwing Angle (U) Screen center Projector foot Screen T op Distance Chart Screen Size D Diagonal (inch) 30 40 60 80 100 120 150 180 200 240 300 Width(H) (inch) 24 32 48 64 80 96 120 144 160 192 240 Width(V) (inch) 18 24 36 48 60 72 90 108 120 144 180 Magnification K 23.
E–14 W ARNING • Installing your projector on the ceiling must be done by a quali- fied technician. Contact your NEC dealer for more inf orma- tion. * Do not attempt to install the projector yourself. • Only use your projector on a solid, le vel surface.
E–15 Wiring Diagram PC CONTROL REMOTE CONTROL INPUT MOUSE OUT S-VIDEO VIDEO AUDIO RGB INPUT 2 AUDIO RGB INPUT 1 L / MONO R Optional Component V cable T o video, S-video, and audio inputs on the projector .
E–16 When using a Macintosh with the projector , set the DIP switches of the supplied pin adapter according to your resolution. After setting, restart your Macintosh.
E–17 3.OPERA TION This section describes how to select a computer or video sour ce, how to adjust the picture, and how to customize the menu or projector settings. General Controls Before you turn on your projector , ensure that the computer or video source is turned on and that your lens cap is remov ed.
E–18 Main Menu Source Select Adjustments Image Options Projector Options Tools Help Source Select RGB 1 RGB 2 Video S-Video PC Card Viewer Adjustments Picture Volume Image Color Temperature Keystone.
E–19 Menu Elements Setup Orientation Page1 Page2 Page3 Front Floor Background Blue Signal Select S-Video Auto Video Auto RGB1 Auto RGB2 Auto OK Cancel Page4 Page4 Setup Page1 Mouse Button Right Hand.
E–20 Adjustments Picture Volume Image Color Temperature Keystone Factory Default Menu Descriptions & Functions Source Select Enables you to select a video source such as a VCR, D VD player , laser disc pla yer , computer or document camera depend- ing on what is connected to your inputs.
E–21 Auto Adjust: When “ Auto Adjust” is set to “On”, the pr ojector automatically determines the best resolution for the current RGB input signal to project an image using NEC’ s Advanced AccuBlend Intelli- gent Pixel Blending T echnology .
E–22 V ideo Mode Gamma: Video Mode Gamma Noise Reduction Color Matrix Projector Options Menu Setup Menu Language English Projector Pointer Pointer 1 Source Display Off On Pointer 1 Pointer 2 Pointer 3 Pointer 4 Pointer 5 Pointer 6 Pointer 7 Pointer 8 Y ou can select one of the follo wing three levels for reducing video noise to your preference.
E–23 Setup Orientation Page1 Page2 Page3 Front Floor Background Blue Signal Select S-Video Auto Video Auto RGB1 Auto RGB2 Auto OK Cancel Page4 Setup Enables you to set operating options. Press “OK” to sav e your changes for all the features of Page1, Page2, Page3 and P a ge4.
E–24 Tools Capture PC Card Files ChalkBoard [Page 3] Setup Page1 Page2 Page4 OK Cancel Page3 PC Card Viewer Options Start Mode Show Folder List Manual Play Auto Play Auto Play Interval sec 15 Captur.
E–25 PC Card Files File Name Size Date @. @.. 12345678.txt 12345678.bmp 12345678.htm <DIR> <DIR> 1234567890 1234567890 1234567890 1999/06/01 HH:MM 1999/06/01 HH:MM 1999/06/17 HH:MM 1999/06/17 HH:MM 1999/06/17 HH:MM Execute Exit Sort Name (abc.
E–26 Using the PC Card Viewer function NO TE: When using the supplied software (CD-R OM) The softwar e is designed to use with a personal computer only . Do not play the softwar e on CD player . Doing so could cause dama ge to speakers. Features The V iewer feature allo ws slides stored on a PC card to be displayed on the projector .
E–27 Installing the PC Card Viewer Software Before Installing Perform the following before installing the PC Card V ie wer software: • If W indows95 is already started, exit all applications. Installa- tion may not be performed properly if any applica tions are run- ning.
E–28 Operating the PC Card Viewer Function from the Projector (playback) This section describes the operation for sho wing slides of presenta- tion documents created using the PC Card V iewer function with the projector . It is also possible to make slides directly from the images projected with the projector .
E–29 A uto Play Mode • If the “ Auto Play” option is selected in “PC Card V iewer Op- tions” of the menu, any gi ven slide will start to play automati- cally .
E–30 Capturing Images Displayed on the Projector Storing images display ed on the projector on the PC card Preparations: Insert the PC card into the card slot. Insert the PC card with the side with the insertion direction ar- row on the top. * Press the eject button to eject the card.
E–31 Uninstalling the PC Card Viewer Software Even if you do no w know the PC Card V iewer softw are's file names or where they are stored, the PC Card V iewer software f iles can be easily remov ed from the system using the "Install/Uninstall Applica- tions" control panel in W indows 95.
E–32 This is the name of a card currently being standardized by the Japan Electronic Industry Association (JEID A) and PCMCIA (Personal Computer Memory Card Interface Association) of the United States. PCMCIA 2.1 PC cards are divided into thr ee types according to their thickness: T ype I (3.
E–33 4. MAINTENANCE This section describes the simple maintenance procedures you should follow to replace the lamp, c lean the filter , and replace the batteries in the remote control.
E–34 2. Remove both old batteries and install ne w ones (AA). Ensure that you hav e the batteries' polarity (+/–) aligned correctly . 3. Slip the cov er back ov er the batteries until it snaps into place. Remote Control Battery Installation 1.
E–35 5. TROUBLESHOOTING This section helps you resolve problems you may encounter while setting up or using the projector . OFF On continually Blinking very rapidly (On and off in a c ycle of 1 sec.) Blinking very rapidly (On and off in a c ycle of 4 sec.
E–36 • Is “PC Card V ie w er” selected from the Source menu? • Is the PC memory card seated in the PC CARD ACCESS slot completely? • Are slide data stored in the PC card? • Ha ve the contents of the PC card been destroyed? • While an image with o ver 1024 2 768 dots is projected, sev er al lines of information will be lost.
E–37 6. SPECIFICA TIONS This section provides technical information about the MultiSync MT840/MT1040/MT1045 Pr ojector’ s performance. Model Number MT840 / MT840G / MT1040 / MT1040G/ MT1045 / MT1045G Optical LCD P anel 1.3” p-Si TFT active-matrix, 800 2 600 dots (MT840) / 1024 2 768 dots (MT1040/MT1045) 1.
E–38 Cabinet Dimensions M E N U E N T E R C A N C E L SELECT POWER STATUS ON / OFF SOURCE AUTO ADJUST AC IN PC CONTROL REMOTE CONTROL INPUT MOUSE OUTPUT USB S-VIDEO VIDEO AUDIO RGB INPUT 2 AUDIO RGB INPUT 1 L / MONO R 1.5 (0.06") 281 (11.06") 73.
E–39 MT1045 M E N U E N T E R C A N C E L SELECT POWER STATUS ON / OFF SOURCE AUTO ADJUST AC IN PC CONTROL REMOTE CONTROL INPUT MOUSE OUTPUT USB S-VIDEO VIDEO AUDIO RGB INPUT 2 AUDIO RGB INPUT 1 L / MONO R PC-CARD 1.5(0.06") 281(11.06") 73.
E–40 51 42 3 10 11 12 13 14 15 6 97 8 D-Sub Pin Assignments Mini D-Sub 15 Pin Connector Pin No. RGB Signal (Analog) YCbCr Signal 1 Red Cr 2 Green or Sync on Green Y 3 Blue Cb 4 Ground 5 Ground 6 Red.
E–41 Timing Chart Y NTSC 640 2 480 60 15.734 - Y P AL 768 2 576 50 15.625 - Y SECAM 768 2 576 50 15.625 - Y VESA 640 2 350 85.08 37.86 31.5 Y MA C 640 2 400 66 35 30.24 Y IBM 640 2 400 70 31.47 25.175 Y VESA 640 2 400 85.08 37.86 31.5 Y VESA 640 2 480 59.
E–42 Cable Connection Communication Pr otocol Baud rate: 38400 bps Data length: 8 bits Parity: No parity Stop bit: One bit X on/off: None Communications Full duplex procedur e: 1 2 54 3 6 7 8 T o RxD of PC © PC Control Connector (DIN-8P) T o TxD of PC § T o GND of PC © NO TE: Pins 2, 3, 5, 6 and 8 ar e used inside the projector .
An important point after buying a device NEC MT1040 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NEC MT1040 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NEC MT1040 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NEC MT1040 you will learn all the available features of the product, as well as information on its operation. The information that you get NEC MT1040 will certainly help you make a decision on the purchase.
If you already are a holder of NEC MT1040, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NEC MT1040.
However, one of the most important roles played by the user manual is to help in solving problems with NEC MT1040. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NEC MT1040 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
