Instruction/ maintenance manual of the product 5 x 5 - X461UN NEC
Go to page of 42
User ’ s Manual MultiSync X462UN MultiSync X461UNV.
Index Declaration of conformity ...................................................................................................... ....................... English-1 Important Information ............................................................
English-1 English For USA FCC Information 1. Use the attached specified cables with the MultiSync X462UN (L468TP)/MultiSync X461UNV (L460NZ) color display so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance.
English-2 Important Information TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT T O RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPT ACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULL Y INSERTED.
English-3 English FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MUL TI-FUNCTION MONIT OR: • DO NOT OPEN THE MONITOR . There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks.
English-4 Contents Power Cord* 1 Setup Manual Remote control cable Clamp x 3 Y our new MultiSync monitor box* should contain the following: • LCD monitor • Power cord* 1 • Video Signal Cable •.
English-5 English This de vice cannot be used or installed without the T abletop Stand or other mounting accessor y f or suppor t. F or proper installation it is strongly recommended to use a trained, NEC authorized service person.
English-6 Attaching Mounting Accessories The display is designed for use with the VESA mounting system. 1. Attach Mounting Accessories Be careful to avoid tipping monitor when attaching accessories. Mounting accessories can be attached with the monitor in the face down position.
English-7 English DOWN button Activates the OSD menu when the OSD menu is turned-off. Acts as button to move the highlighted area down to select adjustment items within OSD menu. EXIT button Activates the OSD menu when the OSD menu is turned-off. Acts as EXIT button within the OSD to move to previous menu.
English-8 T erminal Panel RGB/HV OUT (BNC) T o output the signal from the RGB/HV IN connector or VGA IN connector which is on screen to an input on a separate device. If both signals are not on screen, outputs the signal from RGB/HV IN connector . VIDEO IN connector (BNC and RCA) T o input a composite video signal.
English-9 English LAN port (RJ-45) LAN connection. See page 31. REMOTE IN/OUT Use the optional wired remote control by connecting it to your monitor . NOTE: When you use Remote IN/OUT , IR CONTROL in OSD menu should be NORMAL. Kensington Lock For security and theft prevention.
English-10 POWER button Switches the power on/standby . INPUT button Selects input signal. DVI: DVI DISPLA YPOR T : DPORT VGA: VGA RGB/HV : RGB/HV HDMI: HDMI DVD/HD: DVD/HD1, DVD/HD2, SCART VIDEO: VID.
English-11 English Operating Range for the Option Remote Control Point the top of the remote control toward the sensor unit’s remote control sensor in optional control kit during button operation. Use the remote control within a distance of about 7 m (23 ft.
English-12 1. Determine the installation location CAUTION: Installing your LCD display must be done by a qualified technician. Contact your dealer for more information. CAUTION: MOVING OR INST ALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE.
English-13 English 6. Switch on the power of all the attached external equipment When connected with a computer , switch on the power of the computer first. 7. Operate the attached external equipment Display the signal from the desired input source. 8.
English-14 • AUDIO IN 1, 2 and 3 can be used for audio input. T o select audio source [IN1], [IN2] or [IN3] in AUDIO INPUT in OSD menu or press the AUDIO INPUT button (optional remote control).
English-15 English Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer ’s screen image. Some video cards with a pixel clock over 162MHz may not display an image correctly . Y our LCD monitor displays proper image by adjusting the factory preset timing signal automatically .
English-16 Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD.
English-17 English NORMAL: Displays the aspect ratio the same as it is sent from the source. FULL: Fills entire screen. WIDE: Expands a 16:9 letter box signal to fill entire screen. ZOOM (DYNAMIC): Expands a 4:3 pictures to fill the entire screen with non-linearity .
English-18 Picture Mode DVI, VGA, RGB/HV , DPORT ST ANDARD sRGB AMBIENT1 AMBIENT2 HIGHBRIGHT HDMI, DVD/HD1, DVD/HD2, SCART , VIDEO1, VIDEO2, S-VIDEO, TV* ST ANDARD CINEMA AMBIENT1 AMBIENT2 HIGHBRIGHT AMBIENT Mode The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room.
English-19 English OSD (On-Screen-Display) Controls Press UP or DOWN button to select sub-menu. Press SET . Press UP or DOWN, PLUS or MINUS to select the function or setting to be adjusted. Press MENU or EXIT . Remote Control Press UP or DOWN button to select.
English-20 Setting Default BRIGHTNESS Adjusts the overall image and background brightness. Press + or - to adjust. 70 Note: When AMBIENT1 or AMBIENT2 is selected in picture mode, this function cannot be changed. CONTRAST Adjusts the image brightness in relationship to the background.
English-21 English H RESOLUTION Adjusts the horizontal size of the image. - VGA, RGB/HV inputs only V RESOLUTION Adjusts the vertical size of the image.
English-22 SCHEDULE RESET Resets the following settings within the SCHEDULE menu back to factory setting: - OFF TIMER, SCHEDULE SETTINGS. KEEP PIP MODE Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering of f. OFF When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.
English-23 English INFORMA TION OSD Selects whether the information OSD is displayed or not. The information OSD will be ON, 3 Sec. displayed when the input signal or source changes. The information OSD will also give a warning when there is no-signal or the signal is out-of range.
English-24 LAN SETTING When you use this function, EXTERNAL CONTROL should be “LAN”. NOTE: When changing the LAN SETTING, turn the monitor off and then back on. After turning on the monitor , you need to wait several seconds until the LAN SETTING is applied.
English-25 English INPUT DETECT Selects the method of input detection the monitor uses when more than two input devices FIRST DETECT All inputs except for TV* are connected.
English-26 COLOR SYSTEM The selected Color System depends on the video format of the input signal. AUTO VIDEO1, VIDEO2, S-VIDEO inputs only AUTO Automatically chooses Color System setting based on input signal. NTSC PA L SECAM 4.43 NTSC P AL-60 SCAN MODE Some video formats may require different scanning modes in order to best display the image.
English-27 English NOTE 1: CREA TING A SCHEDULE The schedule function allows the display to be set to power on and off at dif ferent times. Up to seven different schedules can be programmed. T o program the schedule: 1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons.
English-28 REMOTE CONTROL ID FUNCTION REMOTE CONTROL ID The optional remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors.
English-29 English 3. Press the “DISPLA Y” button on the remote control while aiming at the “PRIMAR Y” monitor . The Information OSD will be shown at top left side of the screen. Monitor ID: Displays the ID number of the current monitor within the daisy chain.
English-30 This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C” (See page 23).
English-31 English Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function. NOTE: When you use this function, EXTERNAL CONTROL should be “LAN” (See page 23).
English-32 Preparation Before Use Connect the monitor to a commercially available LAN cable before engaging in browser operations. Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting method.
English-33 English Alert Mail Setting http://<the Monitor ’s IP address>/lanconfig.html This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be sent when an error occurs in the monitor .
English-34 Ultra Narrow Bezel: Provides the optimum solution in a tiling environment. Reduced Footprint: Provides the ideal solution for environments with superior image quality . Color Control Systems: Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards.
English-35 English EDGE COMP function (Page 26) adjusts the brightness dif ference between the center and the edge of the screen. Adjust the brightness in accordance with your monitor . BRIGHTNESS: Reduces the brightness in the center of the screen to allow for better consistency to the brightness at the edge of the screen.
English-36 No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used.
English-37 English Specifications - X462UN Product Specifications LCD Module 46" /1 168 mm diagonal Pixel Pitch: 0.746 mm Resolution: 1366 x 768 dots Color: Over 16 million colors (depending on video card used) Brightness: 700 cd/m 2 (Max.), 500 cd/m 2 (T yp.
English-38 Specifications - X461UNV Product Specifications LCD Module 46" /1 168 mm diagonal Pixel Pitch: 0.746 mm Resolution: 1366 x 768 dots Color: Over 16 million colors (depending on video card used) Brightness: 450 cd/m 2 (Max.), 390 cd/m 2 (T yp.
English-39 English 1) RS-232C input/output Pin No Name 1 connected to 7&8 2 RXD 3 TXD 4 connected to 6 5 GND 6 connected to 4 7 connected to 1&8 8 connected to 1&7 9N C 1 6 5 9 D-SUB 9P This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
English-40 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment.
An important point after buying a device NEC 5 x 5 - X461UN (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NEC 5 x 5 - X461UN yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NEC 5 x 5 - X461UN - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NEC 5 x 5 - X461UN you will learn all the available features of the product, as well as information on its operation. The information that you get NEC 5 x 5 - X461UN will certainly help you make a decision on the purchase.
If you already are a holder of NEC 5 x 5 - X461UN, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NEC 5 x 5 - X461UN.
However, one of the most important roles played by the user manual is to help in solving problems with NEC 5 x 5 - X461UN. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NEC 5 x 5 - X461UN along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
