Instruction/ maintenance manual of the product FP-1600 National Instruments
Go to page of 19
FP-1600 FieldPoint Quick Start Guide 1 Install the Network Module 1 Panel Mount DIN Rail Mount A. Unlock rail clip. A. Unlock rail clip. · Network Module · Mounting Hardware (DIN rail or panel mount.
B. Hook lip on back of module onto top of DIN rail, press down, and snap into place. B. Snap panel mount accessory (which you can order separately) onto module. Panel Mount DIN Rail Mount NOTE: Do not use spliced DIN rails. Use only a single DIN rail.
Install the T erminal Base(s) CAUTION : T erminal bases must be connected to the network module before applying power to the module. Do not connect or disconnect terminal bases while power is applied to the network module. 2 DIN Rail Mount A. Unlock rail clip.
DIN Rail Mount Panel Mount D. Repeat for each terminal base, up to nine for each network module in most cases. Y ou can use one or two extender cables (which you can order separately) if your FieldPoint bank is too long for your available space. E. Place protective cover on last base, and install rail locks at each end.
3 Install the I/O Module(s) A. Align slots on module with guide rails on base, and press onto base until terminal base’ s latch locks the module in place.
Do not use a cable longer than 100 m. If you are using a 100 Mbps Ethernet, National Instruments recommends using a Category 5 shielded twisted-pair Ethernet. If you need to build your own cable, refer to the FP-1600 User Manual for cabling details. 5 Wire Power to Y our FieldPoint System A.
CAUTION: Cascading power from neighboring bases or network modules defeats isolation between cascaded modules. 15 16 V 31 32 C V 1 3 2 C 17 18 CAUTION: Cascading power defeats isolation.
6 Connect to Field Devices Use each I/O module’ s operating instructions, or the diagram under its removable label, to help you connect your field devices.
7 Power Up Y our FieldPoint System CAUTION: T erminal bases must be connected to the FP-1600 before power is applied to the FP-1600. Plug in each power supply to your FieldPoint bank. Y ou should see all except the ST A TUS and PROCESS LEDs flash once, and the POWER LED come on and stay on.
8 Install the FieldPoint Software A. Close all other applications. If you plan to install National Instruments development software such as Lookout, LabVIEW , or Measurement Studio, install them before you install the FieldPoint software. B. Insert the FieldPoint software CD and follow the onscreen instructions.
C. In the Comm Resource Configuration dialog box, select Ethernet as the T ype . D. Click Browse , select the FP-1600, and click the Device Properties button.
E. In the FP-1600 Properties box, enter values for the IP address , Subnet mask , and Time server IP . Y ou might also want to enter a comment to help you identify the FP-1600 module.
If your modules are not listed, check the cable and connections and make sure the modules are all powered on. If you still have problems, refer to your FP-1600 user manual for troubleshooting information. I. Select an input module and click on the start monitoring button to view live data.
10 Configure I/O Modules A. Right-click on the device name in FieldPoint Explorer and select Edit this Device from the pop-up menu. B. Click on the Channel Configuration button to bring up the Channel Configuration dialog box. C. Select the type of channel to show , then select the channel(s) that you want to change.
D. Set the range and output values of the selected channel(s). E. Set the attributes for the selected channel(s) by selecting the attribute and entering the desired value. F . Send commands to the selected channel(s) by choosing a command and value and clicking on Send .
11 Where to Go from Here After you get your hardware up and running, you might want to implement features such as power -up defaults or network watchdog settings. Refer to your FP-1600 user manual or online help for information about features, configuration, application development, and troubleshooting.
FP-1600 Specifications Network interface .................... 10BaseT and 100BaseTX Ethernet Compatibility ........................ IEEE 802.3 Communications rate .................1 0 Mbps, 100 Mbps, autonegotiated Cabling distance ...................
4.31 [109.5] 3.60 [91.44] 4.22 [107.19] Mechanical Dimensions Dimensions are given in inches [millimeters]. 18 fpoint cd.qxd 11/13/00 1:24 PM Page 18.
United States 512 795-8248 Australia 03 9879 5166, Austria 0662 45 79 90 0, Belgium 02 757 00 20, Brazil 011 284 5011, Canada (Calgary) 403 274 9391, Canada (Ontario) 905 785 0085, Canada (Québec) 51.
An important point after buying a device National Instruments FP-1600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought National Instruments FP-1600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data National Instruments FP-1600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, National Instruments FP-1600 you will learn all the available features of the product, as well as information on its operation. The information that you get National Instruments FP-1600 will certainly help you make a decision on the purchase.
If you already are a holder of National Instruments FP-1600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime National Instruments FP-1600.
However, one of the most important roles played by the user manual is to help in solving problems with National Instruments FP-1600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device National Instruments FP-1600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
