Instruction/ maintenance manual of the product 387002x92D Murray
Go to page of 52
The owner must be certain that all the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT P ARTS and the W ARRANTIES. This information must be included to make sure state laws and other laws are followed.
2 F-050717L T ABLE OF CONTENTS W ARRANTY 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RESPONSIBILITY OF THE OWNER 3 . . . . . . . . . . . . . . . . . . . . SAFETY RULES 3 . . . . . . . . . . . . . . . . . . . . .
OWNER’S INFORMA TION 3 F-050717L This instruction book is for several dif ferent models. The instructions ar e written for a person with some mechanical ability . Like most ser- vice books, not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can follow with some mechanical ability .
OWNER’S INFORMA TION 4 F-050717L c. Do not turn sharply . Use care when backing. d. Use counterweights or wheel weights when suggested in the Instruction Book. 18. Do not operate this machine if you are taking drugs or other medication which can cause drowsiness or affect your ability to operate this machine.
SAFE MOWING GUIDE 5 F-050717L Each person that operates power equipment must learn to use correct and safe mowing procedures. T o help you learn, carefully read the following pages. Most of the time the operator was not correctly shown or did not read the instructions on the unit or in the Instruction Book before using the unit.
SAFE MOWING GUIDE 6 F-050717L mower was completely assembled at the store, you must still check the mower according to the assembly instructions. Make sure the mower is correctly assembled and that all fasteners are tight. Make sure the engine has the correct amount of oil.
SAFE MOWING GUIDE 7 F-050717L Also, the grass bagger will function better when the engine is operating at maximum speed. On slopes, decrease the ground speed and use care making sure the mower feels safe to operate. If the weather conditions are bad, do not mow .
STEPS T O FOLLOW 8 F-050717L BEFORE MOWING F Be sure to dress correctly . Wear hard shoes, not sandals or tennis shoes. F Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory replacement blade. F Fill the fuel tank outside.
INTERNA TIONAL PICTORIALS 9 F-050717L INTERNA TIONAL PICTORIALS IMPORT ANT : Some of the following pic- torials are located on your unit or on literature supplied with the product. Be- fore you operate the unit, learn and un- derstand the purpose for each pictorial.
ASSEMBL Y 10 F-050717L ASSEMBL Y This instruction book is for several models. Some parts or accesso- ries are not included on all models. Read and follow the assembly and adjustment instructions for your mower . All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled.
ASSEMBL Y 11 F-050717L MAINTENANCE FREE BA TTER Y IMPORT ANT : Before you attach the battery cables to the battery , check the battery date. The battery date tells if the battery must be charged. 1. Check the top and the side of the battery for the location of the battery date (Figure 2).
ASSEMBL Y 12 F-050717L HOW TO INST ALL THE SEA T Us e the fasteners shown below to install the seat . The fasteners are shown at full size. (A) 1001054 (B) 17x47 1. Carefully remove the plastic bag from the seat. 2. Align the holes in the seat hinge to the holes in the seat (Figure 4).
ASSEMBL Y 13 F-050717L IMPORT ANT! BEFORE YOU ST ART MOWING - Check the engine oil. - Fill the fuel tank with gasoline. - Check the air pressure of the tires. - Check the level of the mower housing. - Make sure the battery cables are attached. - Make sure the wire is attached to the spark plug.
OPERA TION 14 F-050717L Figure 7 Ignition Headlight Switch Parking Brake Lever Lift Lever Throttle Control Lever Blade Rotation Control Shift Lever Clutch / Brake Pedal LOCA TION OF CONTROLS BLADE ROT.
OPERA TION 15 F-050717L A TT ACHMENTS This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper , a lawn aerator , a hopper spreader or a small trailer . This unit can not use attachments that engage the ground like a plow , a disk harrow , or a cultivator .
OPERA TION 16 F-050717L HOW TO USE THE BLADE ROT A TION CONTROL The blade rotation control is next to the steering wheel (Figure 9). U s e the blade rotation control to engage the blade(s) or to operate a snow thrower attachment. 1. Before you start the engine, make sure the blade rotation con- trol is in the DISENGAGE position .
OPERA TION 17 F-050717L HOW TO SET THE P ARKING BRAKE 1. Completely push the clutch/brake pedal forward. 2. Lift the parking brake lever (Figure 10). 3. Remove your foot from the clutch/brake pedal and then release the parking brake lever . Make sure the parking brake will hold the unit.
OPERA TION 18 F-050717L HOW TO OPERA TE WITH THE MOWER HOUSING W ARNING: The deflector is a safety device. Do not re- move the deflector . The deflector forces the dis- charged material toward the ground. Always keep the deflector in the down position.
OPERA TION 19 F-050717L BEFORE ST ARTING THE ENGINE CHECK THE OIL NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer ’ s instructions for the type of gasoline and oil to use.
OPERA TION 20 F-050717L OPERA TING TIPS 1. Check the blade rotation control for correct adjustment. For the blade(s) to disengage correctly , the adjustment must be cor- rect. 2. Before you use the unit, check the oil in the engine and add oil if necessary .
MAINTENANCE 21 F-050717L MAINTENANCE CHART PROCEDURE EACH USE FIRST 2 HOURS EVER Y 25 HOURS EVER Y 50 HOURS EVER Y 100 HOURS BEFORE STORAGE Blade, Inspect and Sharpen √ Blade Rotation Control, Check.
MAINTENANCE 22 F-050717L INSPECT BLADE W ARNING: Before you inspect or remove the blade, disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Check the unit for dam- age. The blade has sharp edges. When you hold the blade, use gloves or cloth material to protect your hands.
MAINTENANCE 23 F-050717L HOW T O ADJUST THE BLADE ROT A TION CONTROL W ARNING: T o prevent an injury , the blade rotation control must operate correctly . 1. Stop the engine. Disconnect the wire from the spark plug. 2. Before you adjust the blade rotation control , check and level the mower housing.
MAINTENANCE 24 F-050717L HOW T O CHECK AND ADJUST THE DRIVE BRAKE Completely push the clutch/brake pedal forward. Set the parking brake. Move the shift lever to the neutral (N) position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads.
MAINTENANCE 25 F-050717L MAINTENANCE FREE BA TTER Y HOW TO REMOVE THE BA TTER Y T o charge or clean the battery , remove the battery from the unit as follows. W ARNING: T o prevent sparks, disconnect the black battery cable from the negative (-) terminal before you disconnect the red cable.
MAINTENANCE 26 F-050717L WHERE TO LUBRICA TE Lubricate the areas shown with engine oil. Apply grease with a brush to the areas shown. NOTE: Apply grease to the steering gear assembly . CAUTION: If the unit is operated in dry areas that have sand, use a dry graphite spray to lubricate the unit.
MAINTENANCE 27 F-050717L HOW TO REMOVE THE MOWER HOUSING 1. Move the lift lever to the lowest position. 2. Move the blade rotation control to the DISENGAGE position. 3. Remove the hair pins and the washers from the adjusting rods (Figure 22). See illustrations “C” and “D”.
MAINTENANCE 28 F-050717L HOW TO LEVEL THE MOWER HOUSING If the mower housing is level, the blade will cut easier and the lawn will look better . W ARNING: Before you make an inspection, adjustment, or repair to the unit, disconnect the wire to the spark plug.
MAINTENANCE 29 F-050717L HOW T O REPLACE THE MOTION DRIVE BEL T REMOV AL 1. Remove the mower housing. See the instructions on “How T o Remove The Mower Housing”. 2. Completely push the pedal forward and engage the parking brake. 3. Remove the idler pulley (Figure 25).
MAINTENANCE 30 F-050717L HOW TO REPLACE THE MOWER DRIVE BEL T 1. Remove the mower housing. See the instructions on “How T o Remove The Mower Housing”. 2. Pull the belt retainer away from the idler pulley and remove the mower drive belt (Figure 28).
MAINTENANCE 31 F-050717L HOW TO INST ALL THE WHEELS If the wheels must be removed for service, make sure they are installed as follows. Front Wheel 1. Make sure the valve stem is to the outside of the tractor . Slide the front wheel on the spindle (See Figure 29).
MAINTENANCE 32 F-050717L HOW TO REPLACE THE FUSE If the fuse is blown, the engine will not start. The location of the fuse is next to the battery . Remove the fuse and replace with a automotive fuse (Figure 31). Figure 31 Automotive Fuse HOW TO REPLACE THE LIGHT BULB 1.
TROUBLE SHOOTING CHART 33 F-050717L PROBLEM: The engine will not start. 1. Follow the steps, “How T o Start The Engine” in this book. 2. Electric-Start Models: Clean the battery terminals. Tighten the cables. 3. Drain the fuel tank. Clean the fuel line.
F-050717L 34 Only use a factory repair part. Repair parts, except for the engine or the transmission, are available from the store where th e unit was purchased, a service shop recommended by the store, or an authorized service shop found in the yellow pages of the telephone di rectory .
NOTES 35 F-050717L.
REP AIR P ARTS MODEL 387002x92D 36 F-050717L CHASSIS & HOOD 26 15 26 16 17 18 19 20 21 20 22 23 26 27 26 26 29 30 31 33 34 35 36 37 38 35 44 25 25 25 24 32 41 26 1 2 45 3 4 5 6 7 8 9 10 11 12 13 1.
REP AIR P ARTS MODEL 387002x92D 37 F-050717L CHASSIS & HOOD Key No. Part No. Description Key No. Part No. Description 1 690566 Seat 2 094154E701 Support, Seat 3 094057 Spring, Seat 4 26x229 Screw .
REP AIR P ARTS MODEL 387002x92D 38 F-050717L MOTION DRIVE 24 10 11 12 13 15 16 17 18 19 20 14 55 21 23 22 25 39 40 41 45 46 49 44 1 3 5 7 6 8 9 3 4 47 52 2 9 1 3 30 3 3 51 35 48 31 33 26 27 14 50 29 2.
REP AIR P ARTS MODEL 387002x92D 39 F-050717L MOTION DRIVE Key No. Part No. Description Key No. Part No. Description 1 091754 Guide, Belt 2 015x84 Locknut, Flange 3 015x79 Nut, Flange 4 01x155 Bolt, He.
REP AIR P ARTS MODEL 387002x92D 40 F-050717L STEERING 1 4 6 7 8 6 10 10 11 13 14 16 17 6 6 42 18 19 20 20 40 22 43 26 25 23 24 22 21 29 27 31 19 38 37 29 28 21 21 6 9 32 32 12 33 33 15 34 30 11 35 3 5.
REP AIR P ARTS MODEL 387002x92D 41 F-050717L STEERING Key No. Part No. Description 1 094134 Wheel, Steering 2 094131 Pin, Retainer 3 01 1x28 Ring, E 4 1001705 Post, Steering 5 17x1 18 W asher 6 26x249.
REP AIR P ARTS MODEL 387002x92D 42 F-050717L MOWER HOUSING SUSPENSION 1 2 3 4 5 3 6 7 8 6 6 6 10 10 11 13 9 15 14 11 13 9 22 18 13 13 20 19 13 9 28 13 30 27 26 25 24 23 29 17 33 12 13 21 30 30 30.
REP AIR P ARTS MODEL 387002x92D 43 F-050717L MOWER HOUSING SUSPENSION Key No. Part No. Description 1 092698 Grip 2 091781 Z Control, Blade Rotation 3 0025x3 Bolt, Hex 4 015x67 Locknut, Hex 5 100171 1E.
REP AIR P ARTS MODEL 387002x92D 44 F-050717L MOWER HOUSING 1 3 48 1 3 7 6 9 9 8 45 21 12 59 11 14 13 25 17 19 20 15 32 16 13 8 10 23 29 18 20 19 30 9 9 14 31 5 27 28 61 26 8 10 4 34 9 24 14 25 5 33 9 .
REP AIR P ARTS MODEL 387002x92D 45 F-050717L MOWER HOUSING Key No. Part No. Description Key No. Part No. Description 1 15x140 Nut, Hex 3 092852 Z Pulley , Jackshaft 4 015x84 Locknut, Flange 5 1001703 .
REP AIR P ARTS MODEL 387002x92D 46 F-050717L ENGINE MOUNT 1 9 10 30 30 9e 9f 9a 9d 9b 9b 9c 2 3 4 5 12 13 6 7 8 11 14 32 32.
REP AIR P ARTS MODEL 387002x92D 47 F-050717L ENGINE MOUNT Key No. Part No. Description 1 092317 Fuel Cap 2 1001752 Fuel T ank 3 095197 Hose Clamp ** 4 7601033 Fuel Line (Must cut to length) ** 5 09519.
REP AIR P ARTS MODEL 387002x92D 48 F-050717L ELECTRICAL SYSTEM 24x30 24x29 94613 P AN FRAME WIRING HARNESS FOR: MAIN HARNESS: 250x143 LIGHT : 250X92 21075 94159 24273 91299 1001993 24273 1 3 5 6 8 7 1.
REP AIR P ARTS MODEL 387002x92D 49 F-050717L ELECTRICAL SYSTEM Key No. Part No. Description 1 250x92 Harness, Light Wire 1001716 Socket, Light 090084 Bulb, Light 2 250x143 Harness, Chassis Wire 3 1001.
50 F-050717L.
INDEX 51 F-050717L A Adjustments Blade Rotation Control, 23 Clutch, 24 Drive Brake, 24 Mower Housing, Level, 28 Attachments, 15, 52 B Battery Charge, 25 Check, 1 1 Clean, 25 Install, 1 1 Removal, 25 S.
52 F-050717L LA WN TRACTOR ACCESSORIES Make your Lawn T ractor do more than you ever imagined. The accessories shown on this page can be used on your Lawn T ractor .
An important point after buying a device Murray 387002x92D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Murray 387002x92D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Murray 387002x92D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Murray 387002x92D you will learn all the available features of the product, as well as information on its operation. The information that you get Murray 387002x92D will certainly help you make a decision on the purchase.
If you already are a holder of Murray 387002x92D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Murray 387002x92D.
However, one of the most important roles played by the user manual is to help in solving problems with Murray 387002x92D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Murray 387002x92D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
