Instruction/ maintenance manual of the product WM63H8 Multiquip
Go to page of 60
OPERA TION AND P AR TS MANUAL THIS MANU AL MUST A CCOMP ANY THE EQUIPMENT A T ALL TIMES. T o find the latest re vision of this publication, visit our website at: www .
P A GE 2 — WM63-SERIES MIXER • OPERA TION AND P AR TS MANU AL — REV . #0 (09/27/12) PROPOSITION 65 W ARNING Engine exhaust and some of its constituents, and some dust created of California to cause cancer , birth defects and other repr oductive harm.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 3 Grinding/cutting/drilling of masonry , concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica.
P A GE 4 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) T ABLE OF CONTENTS WM63H5/WM63H8/WM63E Plaster And Mor tar Mixers Proposition 65 Warning ........................................... 2 Silicosis/Respiratory W ar nings .
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 5 P AR TS ORDERING PROCEDURES www .multiquip .com Or dering par ts has never been easier! Choose fr om three eas.
P A GE 6 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) SAFETY INFORMA TION Do not operate or ser vice the equipment before reading the entire manual. Safety precautions should be follo wed at all times when operating this equipment.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 7 SAFETY INFORMA TION GENERAL SAFETY CA UTION NEV ER ope ra te this equ ipm ent with out pro per pro tec tiv.
P A GE 8 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) SAFETY INFORMA TION MIXER SAFETY D ANGER N E V E R o pe r a t e th e eq u i p m e n t i n a n e xp l o s i v e a t m o sp h er e o r ne ar c o mb us ti b le ma te ri al s .
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 9 SAFETY INFORMA TION FUEL SAFETY (GASOLINE MODELS ONL Y) D ANGER DO NO T star t the engine near spilled fuel or combu stib le fl uids . Fuel is extremely fl ammab le and its vapors can cause an e xplosion if ignited.
P A GE 10 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) SAFETY INFORMA TION T O WING SAFETY CA UTION Chec k with your local county or state safety towing regulations, in addition to meeting Depar tment of T ranspor tation (DO T) Safety T owing Regulations, bef ore towing your mix er .
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 11 T O W BAR TO MIXER CONNECTION Ref erence Figure 1 for the installation of the saf ety chain. 1. Inser t the tow bar through the round opening at the bottom of the mix er stand.
P A GE 12 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) SPECIFICA TIONS T able 1. Mixer Specifications Capacity 6.3 cu. ft (178 liters) Bag Capacity 1-1/2 to 2-1/2 bags W eight 574 lbs. (260 kg.) Height W/Dump Handle 73 in.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 13 DIMENSIONS Figure 3. Dimensions B C A HBC-1 2-INCH BALL COUPLER HPC-1 1-INCH PIN COUPLER OPTIONAL T OW BARS APPROXIMA TE LENGTH 36 IN. (91.44 CM) HLC-1 LOOP COUPLER T able 3.
P A GE 14 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) GENERAL INFORMA TION APPLICA TION The MQ Whiteman WM63 Series mixers (drum capacity of 6.3 cu. ft./178 liters) are shipped completely assembled and hav e been factory tested and are ready for use.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 15 COMPONENTS Figure 4 illustrates the basic components and controls of the WM63 Series mixer . Figure 4. Mixer Components 1. Tires Pl y — The tire ply (lay ers) number is rated in letters.
P A GE 16 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) INSPECTION BEFORE ST ARTING 1. Read all saf ety instructi ons at the beginn ing of manual. 2. Clean the unit, removing dir t and dust, par ticularly the engine cooling air inlet, carburetor and air cleaner .
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 17 INSPECTION V -BEL T CHECK Visually examine the V -belt (Figure 7) and deter mine if it is full of tiny cracks , fray ed, has pieces of r ubber missing, is peeling or otherwise damaged.
P A GE 18 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) Figure 11. Engine Components INITIAL SER VICING The engine (Figure 11) must be checked for proper lubrica tion and filled with fuel prior to operat ion. Ref er to the engine manuf acturer’ s manual for instructions and details of operation and servicing.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 19 ELECTRIC MOTOR ELECTRIC MO TOR F or maintenance care and operation of the electric motor , ref er to your electric motor instr uction booklet fur nished with the motor .
P A GE 20 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) The electr ic motor supplied is wired for 115 V AC grounded operation. Make cer tain that the correct size grounded (3-wires) e xtension cord is used. See T able 7 belo w .
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 21 P ADDLE BLADE ADJUSTMENT Adjust paddles as shown in Figure 13.
P A GE 22 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) ST AR T -UP Th is s ec t io n is in te nd ed to as si st th e op er at or w it h th e in it ial st art- u p of th e un it .
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 23 ST AR T -UP 6. Pla ce the belt slip lev er (Fig ure 19) in the ST AR T/ST OP (disengaged) position.
P A GE 24 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) OPERA TION MIXING/DUMPING 1. The paddle shaft inside the drum should be rotating at this time.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 25 NOTES.
P A GE 26 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) MAINTENANCE (ENGINE) Use T ab le 8 as a gen er al maint ena nce guid eli ne when servici ng yo ur engi ne . Fo r more deta il engi ne main ten anc e inf ormat ion , ref er to the engine owner’ s manual supplied with your engine .
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 27 MAINTENANCE (ENGINE) P erf orm the sche dule d main tena nce proced ure s as defin ed by T able 8 and belo w: D AIL Y Thoroughly remove dir t and oil from the engine and control area.
P A GE 28 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) MAINTENANCE (MIXER) DRUM HEAD SEALS There is 1 set of drum head seals (Figure 29) that will require lubrication. Lubr icate the grease fitting f or each drum seal ev er y 40 hours of operation using any grade lithium base grease.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 29 MAINTENANCE (MIXER) Figure 31. Grease Fittings (Countershaft) WHEEL BEARINGS 1. Afte r ev er y 3 month s of operat ion, remo v e the hub dust cap and inspect the wheel bearings (Figure 32).
P A GE 30 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) 4. If gear teeth are not contacting properly (Figure 34), adjust pillow b lock to correct the prob lem. Figure 34. Gear T eeth Alignment GEAR LUBRICA TION The surf ace of the pinion and main gear (Figure 35) shoul d be very lightly greased.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 31 MAINTENANCE (MIXER) Lug Nut T orque Requirements It is extre mel y i mpo r t ant to ap ply an d m ain tai n p rop er wheel mounting torque. Be sure to use only the f asteners matched to the cone angle of the wheel.
P A GE 32 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) MAINTENANCE (MIXER) SUSPENSION The r igid type axle and associated hardware (Figure 38) should be periodically inspected for signs of excessiv e wear , elongation of bolt holes, and loosening of f asteners.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 33 MAINTENANCE (MIXER) MIXER ST ORA GE F or storage of the mixer for ov er 30 days, the f ollowing is recommended: Dr ain the fuel tank comp letel y , or add ST A-BIL to the fuel.
P A GE 34 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) TROUBLESHOOTING T roubleshooting (Engine) Symptom P ossible Problem Solution Diffi cult to star t, fuel is av ailable, b ut no spark at spark plug. Spark plug bridging? Check gap , insulation or replace spar k plug.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 35 TROUBLESHOOTING T roubleshooting (Engine) - contin ued Symptom Possible Pr oblem Solution Weak in po wer , compression is proper and does not misfi re. Air cleaner dir ty? Clean or replace air cleaner .
P A GE 36 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) Mixer T roubleshooting Blades will not rotate. W or n or def ective V -belt? Replace V -belt. Adjustment le ver mis-aligned? Chec k position of adjustment le ver .
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 37 WIRING DIAGRAM.
P A GE 38 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) EXPLANA TION OF CODE IN REMARKS COLUMN The following section explains the diff erent symbols and remarks used in the P ar ts section of this man ual. Use the help number s fo und on the back page of the man ual if ther e are any questions .
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 39 SUGGESTED SP ARE P AR TS WM63-SERIES PLASTER AND MORT AR MIXER WITH HOND A GX160UT1HX2/GX240UT1HA2 ENGINES AND 1.5 HP ELECTRIC MOT OR. 1 to 3 units Qty . P/N Description 6.
P A GE 40 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) NAMEPLA TE AND DECALS MODEL SERIAL P/N 521232 CAUTION 1. Use manufacturer’s recommended torque values when tightening wheel lug nuts. 2. Use recommended tire pressure values when inflating tires.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 41 NAMEPLA TE AND DECALS NO . P ART NO . P ART NAME QTY . REMARKS 1 EM948630 DECAL, PUSH T O ST OP 1 2 521228 DE.
P A GE 42 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) FRAME ASSY . MOUNT PILLOW BLOCKS FOR PINION SHAFT HERE MOUNT DRUM BEARING HERE MOUNT DRUM BEARING HERE OPTIONA.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 43 NO . P ART NO . P ART NAME QTY . REMARKS 1 514842 LOCK, PIN 1 2 491692 CO TTER PIN 1 3 530023 SPRING LOCKING .
P A GE 44 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) P ADDLE SHAFT ASSY ..
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 45 P ADDLE SHAFT ASSY . NO . P ART NO . P ART NAME QTY . REMARKS 1 514752 P ADDLE SHAFT 1 2 492584 NUT , LOCK 1/.
P A GE 46 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) STEEL TUB ASSY . 17 15 16 15 1 8 9 10 1 1 12 18 P ART OF FRONT FRAME P ART OF REAR FRAME 6 7 18 12 1 1 4 6 5 6.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 47 STEEL TUB ASSY . NO . P ART NO . P ART NAME QTY . REMARKS 1 530028 DR UM BEARING BRA CKET 2 2 3249 CAP , DUST 1 3 20561-001 BEARING SEALED .....................
P A GE 48 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) DRUM AND P ADDLE SHAFT COMPLETE ASSY ..
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 49 DRUM AND P ADDLE SHAFT COMPLETE ASSY . NO . P ART NO . P ART NAME QTY .
P A GE 50 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) AXLE ASSY ..
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 51 AXLE ASSY . NO . P ART NO . P ART NAME QTY . REMARKS 1# 3469 DUST CAP 2 2# 29194 LUG NUTS 8 3 516476 TIRE AND RIM, TO WMASTER II 2 4 8164 CASTLE NUT 1-20 JAM 2 5 EM924008 CO TTER PIN 1/8" X 1-1/2' 2 6 EM511159 W ASHER, FLA T , .
P A GE 52 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) ENGINE ASSY ..
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 53 ENGINE ASSY . NO . P ART NO . P ART NAME QTY . REMARKS 1 EM969013 NUT NYLOK 3/8" NC G5 4 2 3019092 FLA T.
P A GE 54 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) ELECTRIC MOTOR ASSY ..
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 55 ELECTRIC MOTOR ASSY . NO . P ART NO . P ART NAME QTY . REMARKS 1 EM969013 NUT NYLOK 3/8" G5 4 2 3019092 .
P A GE 56 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) CABINET ASSY . 2 6 1 3 4 5 1 COMPLETE LA TCH ASSEMBL Y INCLUDES ITEMS WITHIN DASHED LINES. ITEMS CANNOT BE PURCHASED SEP ARA TEL Y . NOTES: 1 2 8 7 2 10 1 1 12 12 OZ.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 57 CABINET ASSY . NO . P ART NO . P ART NAME QTY . REMARKS 1 515014 CABINET , ENGINE W/DECALS .
P A GE 58 — WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (09/27/12) TERMS AND CONDITIONS OF SALE — P AR TS P A YME NT TERM S T er ms of payment for par ts are net 30 d ays. FREIG HT POLICY Al l p ar ts o rd e r s wi ll be s h ip p ed c o ll e c t or prepaid with the charges added to the invoice.
WM63-SERIES MIXER • OPERA TION AND P ARTS MANU AL — REV . #0 (069/27/12) — P A GE 59 NOTES.
OPERA TION AND P AR TS MANUAL Y our Local Dealer is: HERE’S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING United St a teS Multiquip Corporate Office MQ P ar ts Department 18910 Wilmington A ve. Carson, CA 90746 Contact: mq@multiquip .
An important point after buying a device Multiquip WM63H8 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Multiquip WM63H8 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Multiquip WM63H8 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Multiquip WM63H8 you will learn all the available features of the product, as well as information on its operation. The information that you get Multiquip WM63H8 will certainly help you make a decision on the purchase.
If you already are a holder of Multiquip WM63H8, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Multiquip WM63H8.
However, one of the most important roles played by the user manual is to help in solving problems with Multiquip WM63H8. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Multiquip WM63H8 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
