Instruction/ maintenance manual of the product H Style 600 Series MTD
Go to page of 24
MTD LL C, P .O. BO X 36 1 1 3 1 CLEVEL AND, OHIO 44 1 3 6 - 001 9 Print ed In US A Safe Ope ration Practices • Set- Up • Operation • Ma intenance • Service • T roublesho oting • W arranty W ARNING READ AND FOL LO W ALL S AF ET Y RULES A ND INSTRUCTIONS IN THIS MANUA L BEFORE A T TEMPTING TO OPERA TE THIS MA CHINE .
T o Th e Owner 1 2 Record Product Infor mat ion Befo re set ting up and op erating you r new equipm ent, pleas e loc ate the model p late on the equi pment and re cord the infor mation in the prov ided area to the r ight.
Im por tan t Safe Opera ti on Pr ac ti ces 2 3 T raining Read, u nders tand, and f ollow all ins truct ions on the machine an d in the manual(s) before at tempting to assemb le and ope rate. Keep this manua l in a safe pla ce for futur e and regular r eference an d for order ing repla cement par ts .
4 s ecti On 2 — i MpOr t ant s afe O peratiOn p racti ces Safe Handling of Gasoline T o av oid p erso nal injur y or prop er ty dam age use ex treme c are in handli ng gasolin e.
5 s ecti On 2 — i MpOr t ant s afe O peratiOn p racti ces Maintenance & S torage Never tam per with s afet y devices. Ch eck their pr oper ope ration reg ularly. Refer to the maintena nce and adjust ment sec tions of this ma nual. Befo re cleaning, r epairin g, or inspe cting ma chine diseng age all control l evers and sto p the engine.
Assembly Handle Obse rve the l ower rear area of the s now thrower to be sure both ca bles are ali gned with ro ller guid es befor e pivoting the handl e upward. Se e Fig. 3- 1 . NOTE: M ake cert ain the upp er ends of each c able are seated p roperl y in its bra cket.
Chute Directional Control Remove the p lastic cap (if p resent), flat w asher and hair pin clip fro m the end of the chu te direc tional control . See Fig. 3- 4. Inser t the en d of the chute direc tiona l control into the lower br acket and secu re with the f lat washer an d hairpin clip just r emoved.
Adjustments Skid Shoes The sn ow thrower skid s hoes are adj usted upward at th e fac tory for ship ping pur poses. Adjus t them downwar d, if desire d, prior to oper ating the snow throwe r .
Auger C ontrol W ARN ING ! Prior to ope rating your snow throwe r , caref ully read an d follow all ins truc tions be low . Per form all adjus tments to ver if y your snow thrower is ope rating safe ly and pro perly.
Snow thrower contro ls and features a re describ ed bel ow and illust rated in Fig. 4 - 1 . NOTE: Fo r detaile d informati on on all eng ine controls, re fer to the sep arate T ecumseh Engin e Oper ator’s Manual.
Throttle Control The thr ottle contro l is locate d on the rear of the engin e. It regulates the s peed o f the engine an d will shut o ff th e engine wh en moved into the STOP pos ition. Primer Pressing the p rimer for ces fuel dire ctly into the engi ne’ s car buretor to aid in col d-weath er sta rting .
Chute Direc tional C ontrol The chute di rect ional control is l ocated on l ef t side of the snow thrower. T o chan ge the direc tion in w hich snow is thrown, tu rn chute dire ctiona l control as foll ows: Crank clo ckwis e to discharge to the le ft .
Starting The Engine Atta ch spark plu g wire to spark p lug. Make cer tain the meta l loop on th e end of the spa rk plug wire (ins ide the rubb er boot) is f astened s ecurely over th e metal tip o n the spark p lug. Make cer tain bot h the auger contro l and drive control a re in the dise ngaged (releas ed) posit ion.
T o Engage Dri v e With the th rottle contr ol in the Fast ( rab bit) positio n, move shif t lever into on e of the five for ward (F) p ositions or t wo revers e (R ) pos itions. Se lec t a spee d approp riate for the snow conditi ons and a pace you ’ re comfor tab le with.
Maintenance Engine Refe r to the T e cumseh Engin e manual packe d with your machine fo r all engine m aintenance. Sha ve Plat e and Skid Shoes The shave plate an d skid sho es on the b ottom of th e snow thrower are su bjec t to wear . They shou ld be checke d perio dically and rep laced when n ecessar y .
Auger Sh af t At least on ce a season, rem ove the shear pins fr om the auger shaf t. Spr ay lubricant insi de the shaf t and aro und the spacer s and the f lange b earings fo und at either e nd of the shaf t.
Drive Control When th e drive control is re leased an d in the disenga ged “up” positi on, the cab le should h a ve ver y lit tle slack . It shoul d NOT be tight.
Belt Replacement Auger Belt T o remove and repl ace your snow thrower ’ s auger b elt, pr oceed as foll ows: T o prevent spillag e, place a piece of p lastic wr ap under the gas cap an d tighten secur ely . Remove the p lastic be lt cover on the front o f the engine by removin g the two s elf-tap ping screws .
Remove the b elt fro m around the aug er pulley, and slip the bel t bet ween the sup por t bracket and th e auger pul ley . See Fig . 7 -5. Reassem ble auger b elt by foll owing instr uctio ns in reverse orde r .
Slip the dr ive belt of f the p ulley and be twee n fric tion whee l and fri ction w heel disc . See Fig . 7 - 7 . Remove and re place bel t in the reverse o rder .
Caref ully remove the h ex nut which s ecures the he x shaf t to the snow thrower f rame and li ghtly tap the sh aft ’s end to dislod ge the ball b earing fr om the right sid e of the fram e. See Fig. 7-9 . NOTE: B e caref ul not to damage the thr eads on the shaf t .
22 Pr oblem Cau se Remedy Engi ne fail s to start Chok e con trol not i n ON position. Spark plug w ire d isconn ec t ed. F uel tank empty or stale fuel. Engi ne not primed. F aulty spa rk plug. Safety ke y not inserted . 1. 2. 3. 4. 5. 6. Mov e chok e c ontrol to ON posi tion.
C omponen t Pa r t Nu mber and Desc ript ion 9 29 - 007 1 Ex tention Cord, 1 1 0V 954- 0 4050 Auger Drive Belt 7 54 - 03 67 Wheel D rive Belt 68 4- 0 4 1 5 3 F ric tion Wheel A ssembly 93 5- 04 054 F ric tion Wheel R ubber 9 25- 1 6 58 Halogen L amp, 1 2V , 27W 738- 04 1 24 A Shear Pin, 1 .
MANUF A CTURER’S LIMITED W ARRANTY FOR GDO C-100 015 RE V . B Th e limi ted w arr an t y se t for th b elow i s give n by M TD LL C wi th re spe ct t o new me rch andi se pur ch ase d and u sed i n .
An important point after buying a device MTD H Style 600 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought MTD H Style 600 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data MTD H Style 600 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, MTD H Style 600 Series you will learn all the available features of the product, as well as information on its operation. The information that you get MTD H Style 600 Series will certainly help you make a decision on the purchase.
If you already are a holder of MTD H Style 600 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime MTD H Style 600 Series.
However, one of the most important roles played by the user manual is to help in solving problems with MTD H Style 600 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device MTD H Style 600 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
