Instruction/ maintenance manual of the product EM316E3 MRV Communications
Go to page of 19
EM316E3 EM316E3SF E3 Fiber Modem Fiber Driver Module User’s Guide.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 2 Registration Card Your name: Mr./Ms____________ _______________________________ Organization: _________________ _______Dept.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 3 EM316E3 EM316E3SF E3 Fiber Modem Fiber Driver Module User’s Guide.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 4 TABLE OF CONTENTS 1 INTRODUCTION 2 HARDWARE INSTALLATION 3 TROUBLESHOOTING 4 TECHNICAL SPECIFICATIONS 5 CONTACT INFORMATION 6 GLOSSA.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 5 1 INTRODUCTION About this Manual Before unpacking please refer to section 2 (Hardware Installation) This manual is a guide to the installati on and operation of the EM316E3 Fiber modem.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 6 Features • E3 conversion between coax media and fiber media • Supports ITU-T G.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 7 Display Information (LED Definition) • PWR: illuminates when unit is powered (green colo r) • LPBK: illuminates (yellow color) w.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 8 Configuration Jumper Settings: (Factory Default) CONFIGURING THE SWITCH (S1) SWITCH SETTINGS RESULTS *ON Force switches selections (.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 9 Theory of Operation Block diagram of the Modem/Converter is shown below (fig. 1) Fig. 1 Block Diagram of EM316DS3 E3 Line Receiver to fiber optic Transmitter : The receiver Line Interface Unit (LIU) receives the E3 signal an d performs clock recovery and data detection.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 10 Switch LPBK/NORM is set to OFF Switch LPBK/NORM is set to OFF Loop Back Control: By NMS command or manually by a switch Loop back can be forced regardless of management by turning switch 1 MAN/NMS to ON and switch 3 NORM/LPBK to ON.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 11 2 HARDWARE INSTALLATION PREP ARA TION STEP 1 Follow all Safety Regulations 1 Eliminate static electricity in the workplace by grounding operators, equipment, and devices (components and computer boards).
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 12 f) ESD protective floor or mat: The mat must be grounded through a current- limiting resistor.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 13 UNIT INSTALLATION STEP 1 Remove required amount of bla nk panels from the NC316BU-xx. NOTE : Per FCC regulations, either a panel or a module should always cover chassis slots. FIGURE 1.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 14 STEP 3 Insert the module into the NC316BU-xx unit NOTE: To avoid dam aging any components on the m odule, handle it by the edges, using your thumb to push it securely inside the ch assis.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 15 3 TROUBLESHOOTING The Fiber Driver series are highly reliable units. If there are any operating problems, the fault probably lies in some other aspect of the configuration.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 16 4 TECHNICAL SPECIFICATIONS Electrical 5VDC @ 2 Amps Max Hot Swappable Operating Temperature Range 0 ° C - +50 ° C (32 ° F – 12.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 17 5 CUSTOMER SUPPORT Contact Information If you have any questions, please do not hesitate to contact us at: Americas Support MRV (East Coast USA) 295 Foster Street Littleton, MA 01460-2016 Tech Support: (800) 338-5316 Tech Support: (978) 952-4700 E-mail: support@fiberdriver.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 18 5 GLOSSARY Complete definition of networking term s (jargon) used in this manual, may be found on our ftp site: ftp://ftp.fiberdriver.com/pub/doc/Glossary.pdf 6 ORDERING INFORMATION Please visit us at http://www.
Fiber Driver EM316E3 & EM316E3SF P/N: 1226006-001, REV_L PAGE 19 Place Stamp Here ---------- -------- -------- ---------- -------- ---- ---------- -------- -------- ---------- -------- ---- ---------- -------- -------- ---------- -------- ---- 8928 Fullbright Avenue Chatsworth, California 91311 U .
An important point after buying a device MRV Communications EM316E3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought MRV Communications EM316E3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data MRV Communications EM316E3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, MRV Communications EM316E3 you will learn all the available features of the product, as well as information on its operation. The information that you get MRV Communications EM316E3 will certainly help you make a decision on the purchase.
If you already are a holder of MRV Communications EM316E3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime MRV Communications EM316E3.
However, one of the most important roles played by the user manual is to help in solving problems with MRV Communications EM316E3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device MRV Communications EM316E3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
