Instruction/ maintenance manual of the product UC-7420/7410 Moxa Technologies
Go to page of 106
UC-7420/7410 User ’ s Manual Third Edition, June 2005 www .moxa.com/product Moxa Technologies Co., Ltd. Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Web: www.
UC-7420/7410 User’s Manual The software d escribed in t his manual is furnished u nder a license a greement and m ay be used only in accordance with the term s of that agreement. Copyright Notice Copyright © 2005 Moxa Technologies Co., Ltd. All rights reserved.
Table of Contents Chapter 1 Introduction .................................................................................................. 1-1 Overview...................................................................................................
Compiling tcps2.c..................................................................................................... 2-16 Uploading tcps2-release a n d Running the Pr ogram ................................................. 2-17 Testing Procedure Summary .
W indows UC Finde r .............................................................................................................. .. 6-2 Installing th e Software.........................................................................................
1 1 Chapter 1 Introduction Welcome to M OXA UC-742 0/7410 RISC -based Com munication Pl atforms. A vailable features include eight RS-232/422/485 seri al ports, dual 10/100 Mbps Ethe rnet ports, a PCM.
UC-7420/7410 User’s Manual Introduction 1-2 Overview UC-7420/741 0 RISC-based C ommunicat ion Platfo rms are i deal for embedded applications. UC-7420/7 410 has eig ht RS-232/ 422/485 ser ial ports,.
UC-7420/7410 User’s Manual Introduction 1-3 y PCMCIA/CompactFlash expansion ( UC-7420 only) y USB Host for mass storage device (UC-7420 on ly) y LCM display and Keypad for HMI y Linux-rea dy communi.
UC-7420/7410 User’s Manual Introduction 1-4 Hardware Introduction Appearance and Dimensions Appearance UC-7410/7420 Rear Vie w DC 12-48V USB LAN1 LAN2 Console V+ V- PCMCIA CF 12-48 VDC Power Input CF x 1 PCMCIA x 1 10/100 Mbps Ethernet x 2 USB 2.0 Host x 2, A T ype Connector USB 1.
UC-7420/7410 User’s Manual Introduction 1-5 Dimensions 197 mm [7.76"] 125 mm [4.92"] 44 mm [1.73"].
UC-7420/7410 User’s Manual Introduction 1-6 Hardware Block Diagram The following block diagram shows the layou t of UC-7420’s internal componen ts (the layout for UC-7410 is sl ightly di fferent).
UC-7420/7410 User’s Manual Introduction 1-7 Reset-type Buttons UC-7420/7410 ha s two reset-type button s. The button lab eled Reset has the same effect as unpluggin g the powe r and the n plugging the powe r back in. The button la beled Re set to default returns UC-7420/7410 to the factory default parameter configuration.
UC-7420/7410 User’s Manual Introduction 1-8 Placement Options W all or Cabinet The two metal brackets that co me standard with UC-7420/7410 are used to attach UC-7420/7410 to a wall, or the inside of a cabinet. Use two scre ws per bracket first to attach the brackets to the bottom of the UC-7420/7410 (Fig.
UC-7420/7410 User’s Manual Introduction 1-9 DIN-Rail Mounting The aluminum DIN-Rail attachm ent plate is included in the package. If you need to reattach the DIN-Rail attachment plate to UC-7420/7410, make sure the stiff metal spring is situated towards the top, as shown in the figures b elow.
UC-7420/7410 User’s Manual Introduction 1-10 y You can use the type of signal transmitted through a wire to determine which wires should be kept separate. The rule o f thumb is that wiring that shares sim ilar electrical characteristics can be bundled toge ther.
UC-7420/7410 User’s Manual Introduction 1-11 Connecting to a Serial Device Use properly wired serial cables to conn ect UC-7420/7410 to serial devices. UC-7420/7 410’s serial ports (P 1 to P8) use 8-pin RJ 45 connectors. T he ports can be configured by software f or RS-232, RS-422, or 2-wire RS-485 .
UC-7420/7410 User’s Manual Introduction 1-12 Software Introduction Software Architecture The Linux operating system that is pre-installed in UC-7420/7410 follows th e standard Linux architecture, making it easy to po rt programs that follow the POSIX standard to UC-7420/7410.
UC-7420/7410 User’s Manual Introduction 1-13 services and daemons. During this time, the kern el will start searching for system configuration parameters via rc or inittab.
UC-7420/7410 User’s Manual Introduction 1-14 OS shell command bash Busybox Linux normal command u tility collection Utilities tinylogin lo gin and u ser manager utility telnet telnet client program .
UC-7420/7410 User’s Manual Introduction 1-15 Protocol stacks and utilities Arp (utility) N/A Yes Yes iptable N/A N/A Yes Open VPN N/A N/A Yes WatchDog API N/A N/A Yes Crontable N/A N/A Yes upfirm N/.
2 2 Chapter 2 Getting Started In this chapter, we explain how to conn ect UC-7420/7410, turn on the power, and then get started using the programm ing and ot her functio ns.
UC-7420/7410 User’s Manual Getting Started 2-2 Powering on UC-7420/7410 Connect the SG wire to the Shielded Con tact located in the upp er left corner of the UC-7420/7410, and then power on U C-7420/7410 by conn ecting it to the power adaptor. It takes ab out 30 to 60 seconds for the system to boo t up.
UC-7420/7410 User’s Manual Getting Started 2-3 Telnet Console If you know at least one of the tw o IP addresses an d netmasks, then you can use Telnet to c onnect to UC-7420/7410’s co nsole utility. The default IP a ddress and Netm ask for each of the two ports are given below: Default IP Address Netmask LAN 1 192.
UC-7420/7410 User’s Manual Getting Started 2-4 ATTENTION Serial Console Reminder Remember to choose VT100 as the terminal type. Use cable C BL-RJ45F9- 150, which com es with UC-7420/7410 , to connect to the serial console por t.
UC-7420/7410 User’s Manual Getting Started 2-5 Linux Users From a Linux machine, use t he “ssh” command to access UC-7420/7410’s C onsole utility via SSH. #ssh 192.168.3.127 Select yes to complete the connection. [root@bee_notebook root]# ssh 192.
UC-7420/7410 User’s Manual Getting Started 2-6 Dynamic IP addresses : By default, UC-7420/7410 is configured for “static” IP addr esses. To configure one or both LAN ports to request an IP address dynami cally, replace static with dhcp and th en delete the address, network , netmask, and broa dcast lines.
UC-7420/7410 User’s Manual Getting Started 2-7 NOTE After changing the IP settings, use the networking restart command to activate the new IP address. However, the LCM display will still sh ow the old IP address. To update the LCM display, you will need to reboot the UC-7420 /7410.
UC-7420/7410 User’s Manual Getting Started 2-8 3. Configure the Wireless LAN card’s d efault SSID setting profile. (Default SSID is “any”) #vi /etc/wlan/wlan.conf // Consult your network ad ministrator for SSID required in your wireless network.
UC-7420/7410 User’s Manual Getting Started 2-9 IEEE802.11g The following I EEE802.11g wireless modules are supported: y ASUS — WL -107g y CNET — CWC -854 (181D version) y Edmiax — EW-7108PCg y Amigo — AWP-914W y GigaByte — GN-WMGK y Other brands that use the Ralink RT2560 series chip set To configu re the WLAN for IEEE80 2.
UC-7420/7410 User’s Manual Getting Started 2-10 3. Additional WLAN parameters are contained in the file RT2500STA.dat . To open the file, navigate to t he RT2500ST A folde r and invoke vi, or ty pe the follo wing comm and #vi /etc/Wireless/RT2500STA/RT2500STA.
UC-7420/7410 User’s Manual Getting Started 2-11 NetworkT ype —Sets the wireless operation mode Setting Explanation Infra Infrastructure mode (use s access points to transm it data) Adhoc Adhoc mod.
UC-7420/7410 User’s Manual Getting Started 2-12 T urboR ate —Enabl es or disables T urboRate Setting Explanation 0 disable 1 enable BGProtection —Sets 1 1b/1 1g protection (t his functio n is fo.
UC-7420/7410 User’s Manual Getting Started 2-13 Test Program — Developing Hello.c In this section, we use the standard “Hello” programming example to illu strate how to develop a program for UC-7420/7 410. In gene ral, prog ram developm ent involves t he followi ng seven st eps.
UC-7420/7410 User’s Manual Getting Started 2-14 If there isn’t enough “Available” space for you r application, you will need to delete some existing files. To do this, connect your PC to the UC-7420 /7410 with the console cab le, and then use the console utility to delete the files from UC-7420/7410 ’s flash memory.
UC-7420/7410 User’s Manual Getting Started 2-15 Uploading “Hello” to UC-742 0/7410 and Running the Program Use the follo wing comm and to upl oad hello-release to the UC-7420/7410 via FTP.
UC-7420/7410 User’s Manual Getting Started 2-16 Compiling tcps2.c The source code for the tcps2 exam ple is located on the CD -ROM at CD-ROM://example/TCPServer2/tcps 2.c . Use the following commands to copy the file to a specific directory on your PC.
UC-7420/7410 User’s Manual Getting Started 2-17 Uploading tcps2-release and Running the Program Use the following commands to use FTP to up load tcps2-release to the UC-7420/7410.
UC-7420/7410 User’s Manual Getting Started 2-18 4. The program should start running in the background. Use either the #jobs or #ps –ef command to check if the t cps2 program is actuall y running i n the backgr ound. #jobs // use this command to check if the program is running 192.
UC-7420/7410 User’s Manual Getting Started 2-19 158 root 1532 S /sbin/getty 115200 ttyS1 162 root 3652 S /usr/sbin/sshd 163 root 2208 S -bash 169 root 2192 S ftpd: 192.
UC-7420/7410 User’s Manual Getting Started 2-20 NOTE The tcps2.c application is a simple example designe d to give use rs a basic unde rstanding of the concepts inv olved in com bining Ethe rnet comm unication and serial port c ommuni cation. However, the example program has some limita tions that make it unsu itable for real-life applications.
3 3 Chapter 3 Managing Embedded Linux This chapte r includes inf ormati on about vers ion contr ol, deploy ment, up dates, and peri pherals. The information in this chapter will be particu larly useful when you need to run the same application on several UC -7420/74 10 units.
UC-7420/7410 User’s Manual Managing Embedded Linux 3-2 System Version Information To determine the hardware capability of your UC-7 420/7410 , and what kind of software functions are supported , check the vers ion numbers of your UC-7420/7410 ’s hardware, kern el, and user file system.
UC-7420/7410 User’s Manual Managing Embedded Linux 3-3 Since different Flash disks have different sizes, it’ s a good idea to check the size of your Flash disk before upgrading the firmware, o r before using the disk to stor e your application and data files.
UC-7420/7410 User’s Manual Managing Embedded Linux 3-4 226 Transfer complete. ftp> get UC7420-1.5.frm local: UC7420-1.5.frm remote: UC7420-1.5.frm 200 Port command successful. 150 Opening data connection for UC7420-1.5.frm 226 Transfer complete. 13167772 bytes received in 2.
UC-7420/7410 User’s Manual Managing Embedded Linux 3-5 Backing Up the User File System 1. Create a back up file. The s pecific com mands used t o back up the user file sy stem depen d on whether the firmware version is earlier or later than version V1.
UC-7420/7410 User’s Manual Managing Embedded Linux 3-6 Back up the user file system to a PC (refer to the previous subsection, “Backing Up the User File System,” for instructions), and then typ e the follo wing commands to copy the backup to ad ditional UC-7420/7410 un its.
UC-7420/7410 User’s Manual Managing Embedded Linux 3-7 192.168.3.127 – PuTTY root@Moxa:~# cd /etc root@Moxa:/etc# ps -ef PID Uid VmSize Stat Command 1 root 1296 S init 2 root S [keventd] 3 root S .
UC-7420/7410 User’s Manual Managing Embedded Linux 3-8 192.168.3.127 – PuTTY root@Moxa:~# ps -ef PID Uid VmSize Stat Command 1 root 1296 S init 2 root S [keventd] 3 root S [ksoftirqd_CPU0] 4 root .
UC-7420/7410 User’s Manual Managing Embedded Linux 3-9 SxxRUNFILE stands for S: start the run file while linux bo ots up. xx : a number between 00 -99. The smaller number has a higher priority. RUNFILE: the file name. 192.168.3.127 – PuTTY root@Moxa:/ect/rc.
UC-7420/7410 User’s Manual Managing Embedded Linux 3-10 192.168.3.127 – PuTTY root@Moxa:~# date Fri Jun 23 23:30:31 CST 2000 root@Moxa:~# hwclock Fri Jun 23 23:30:35 2000 -0.
UC-7420/7410 User’s Manual Managing Embedded Linux 3-11 Save the shell script using a ny file nam e. E.g., fixtime How to run the shell script automa tically when the kernel boots up Copy the example shell script fixtime to directory /etc/init.d , and then use chmod 755 fixtime to change the shell script mod e.
UC-7420/7410 User’s Manual Managing Embedded Linux 3-12 Connecting Peripherals USB Mass S torage This function is o nly available for firm ware version V1. 5 (and later versi ons). The UC-7420/7410 supports PNP (plug -n-play), and hot pluggability for connecting USB mass storage devices.
4 4 Chapter 4 Managing Communications In this chapt er, we ex plain how to configure UC -7420/741 0’s various comm unication funct ions. The following topics are covered in this chapter: Telnet .
UC-7420/7410 User’s Manual Managing Communication 4-2 Telnet / FTP In addition to suppo rting Telnet client/server and FTP client/server, the UC-7420/7410 system also supports SSH and sftp client/server. To enable or disable the Telnet/ftp server, you first need to edit the file /etc/inetd.
UC-7420/7410 User’s Manual Managing Communication 4-3 /usr/www/cgi-bin/ Before you modify the homepage, use a browser (such as Microsoft Intern et Explore or Mozilla Firefox) from your PC to test if the Apach e Web Server is working. Type the LAN1 IP address in the browser’s address box to op en the homepage.
UC-7420/7410 User’s Manual Managing Communication 4-4 To open the de fault CGI t est script re port page, t ype http://192.168.3.127 /cgi-bin/test-cgi in you r browser’s address box. NOTE The CGI f unction is e nabled b y default. If y ou want t o disable the f unction, m odify the fil e /etc/apache/httpd.
UC-7420/7410 User’s Manual Managing Communication 4-5 Step 2: Use the follow ing comm ands to config ure the Apache we b server’s DocumentR oot: #cd /etc/apache #vi httpd.conf …… DocumentRoot “/mnt/hda” //Change the document root directory //to your CF card.
UC-7420/7410 User’s Manual Managing Communication 4-6 IPTABLES IPTABLES is an administrative tool for setting up , maintaining, and insp ecting the Linux kernel’s IP packet filter rule tables. Seve ral different tables are defined, with each table con taining built-in chains and user-defi ned chains.
UC-7420/7410 User’s Manual Managing Communication 4-7 UC-7420/741 0 supports the following s ub-modules. B e sure to use the module t hat matches you r application.
UC-7420/7410 User’s Manual Managing Communication 4-8 The basic syntax t o enable an d load an IPT ABLES module is as follows: #lsmod #modprobe ip_tables #modprobe iptable_filter Use lsmod to check if the ip_tables m odule has alr eady been loade d in the UC-7420/7410.
UC-7420/7410 User’s Manual Managing Communication 4-9 OUTPUT: For locally -generated packets. FORWARD: For packets routed out through th e UC-7420/7410. PREROUTING: To alter packets as soon as they come in. POSTROUTING: To alter packets as they are about to be sent out.
UC-7420/7410 User’s Manual Managing Communication 4-10 NAT NAT (Network Address Trans lation) pr otocol tr anslates IP a ddresses used on one network different IP addresses use d on anot her networ k. One networ k is designat ed the insi de network and the other is the outside network.
UC-7420/7410 User’s Manual Managing Communication 4-11 # Step 1. Insert modules. # Here 2> /dev/null means the standard error messages will be dump to null device.
UC-7420/7410 User’s Manual Managing Communication 4-12 The pppd options are descri bed below: connect ‘chat etc...’ This option gives the command to contact the PPP server.
UC-7420/7410 User’s Manual Managing Communication 4-13 How to check the connection Once you’ve set up a PPP connection, the re are so me steps you can take t o test the connection. First, type: /sbin/ifconfig (The folder ifconfig may be located elsewhe re, dependin g on your di stributi on.
UC-7420/7410 User’s Manual Managing Communication 4-14 Setting up a Machine for Incoming PPP Connections This first example applies to using a modem, and requiring authorization with a usern ame and password. pppd/dev/ttyM0 115200 crtscts modem 192.
UC-7420/7410 User’s Manual Managing Communication 4-15 no_root_squash If no_root_squash is selected, then the root on the client machin e will have the same level of access to files on the system as the root on the server.
UC-7420/7410 User’s Manual Managing Communication 4-16 Steps 2 & 3: #mkdir –p /home/nfs/public #mount –t nfs NFS_Server(IP):/directory /mount/point Example : #mount –t nfs 192.168.3.100/home/public /home/nfs/public Mail smtpclient is a minimal SMTP client th at takes an email message body and passes it on to an SMTP server.
UC-7420/7410 User’s Manual Managing Communication 4-17 20: system.9.1.3.4 (octet st ring) The MIB module for ma naging IP and ICMP i mplementa tions 21: system.9.1.3.5 (octet st ring) The MIB module for ma naging UDP implem entations 22: system.9.1.
UC-7420/7410 User’s Manual Managing Communication 4-18 Setup 1: Ethernet Bridging for Pr ivate Networks on Different Subnets 1. Set up four machines, as show n in the following diagram. OpenVPN A OpenVPN B Host A eth0: 192.168.2.171 Host B eth0: 192.
UC-7420/7410 User’s Manual Managing Communication 4-19 fi i=`expr $i + 1` read f1 f2 case “$f1” in address ) IPADDR=$f2 ; ; netmask ) NETMASK=$f2 ; ; broadcast ) BROADCAST=$f2 ; ; esac done brea.
UC-7420/7410 User’s Manual Managing Communication 4-20 # connect tap device to the bridge brctl addif br0 tap${i} # null ip address of tap device ifconfig tap${i} 0.0.0.0 promisc up i=`expr $i + 1` if [ $i -ge $maxtap ]; then break fi done # null ip address of internal interface ifconfig $iface 0.
UC-7420/7410 User’s Manual Managing Communication 4-21 4. Create a configuration file named A-tap0-br.co nf and an execut able script file name d A-tap0-br.sh on OpenVPN A. # point to the peer remote 192.168.8.174 dev tap0 secret /etc/openvpn/secrouter.
UC-7420/7410 User’s Manual Managing Communication 4-22 virtual device, it sends the traffic to its peer. 7. To create an indirect connectio n t o Host B fr om Host A, y ou need to a dd the fol lowing routing item: route add –net 192.168.4.0 netmask 255.
UC-7420/7410 User’s Manual Managing Communication 4-23 Setup 3: Routed IP 1. Set up four machines as shown in the following diag ram: OpenVPN A OpenVPN B Host A eth0: 192.168.2.171 Host B eth0: 192.168.4.172 ixp0: 192.168.8.174 eth1: 192.168.2.173 local net local net Internet Internet ixp1: 192.
UC-7420/7410 User’s Manual Managing Communication 4-24 Note that the param eter “ifconfig” defines t he firs t argument as t he local internal interface and the second argument as the intern al interface at the remote peer. Note that $5 is the argument that the OpenVPN program passes to the script file.
5 5 Chapter 5 Programmer’s Guide This chapter includes importan t information for programmers. This following functions are covered in this chapter: Flash Memory Map Linux Tool Chain Introdu.
UC-7420/7410 User’s Manual Programmer’s Guide 5-2 Flash Memory Map Partition sizes are hard coded into th e kernel bina ry. To chang e the partition sizes, you will need to rebuild the kernel.
UC-7420/7410 User’s Manual Programmer’s Guide 5-3 Obtaining help Use the Linux man utility to obtain help on many of the utilities provid ed by the tool chain .
UC-7420/7410 User’s Manual Programmer’s Guide 5-4 2. Use the foll owing comm and on the h ost to change to the di rectory that contains hello-de bug : cd /my_work_directory/myfilesystem/testprograms 3. Enter the following command: #ddd --debugger mxscaleb-gdb hello-debug & 4.
UC-7420/7410 User’s Manual Programmer’s Guide 5-5 WDT (Watch Dog Timer) This function is o nly available for firm ware version V1. 5 (and later versi ons). 1. Introductio n The WDT works like a watch dog function. You can enab le it or disable it.
UC-7420/7410 User’s Manual Programmer’s Guide 5-6 int swtd_disable(int fd) Description: Disable the application to ack sWatchDo g. And the kernel will be auto ack it. User does not to do i t at perio dic. Input : int fd - the file handle from swtd_open() return value.
UC-7420/7410 User’s Manual Programmer’s Guide 5-7 int swtd_close(int fd) Description: Close the file handle. Input : int fd - the file handle from swtd_open() return value. Output: OK will be zero. The other has s ome error, t o get error code from errno( ).
UC-7420/7410 User’s Manual Programmer’s Guide 5-8 #include <sys/stat.h> #include <sys/ioctl.h> #include <sys/select.h> #include <sys/time.h> #include <moxadevice.h> static void mydelay(unsigned long msec) { struct timeval time; time.
UC-7420/7410 User’s Manual Programmer’s Guide 5-9 UART The normal tty de vice node is located at /dev/ttyM0 … ttyM7 , and the m odem tty dev ice node is located at /dev/cum0 … cum7 .
UC-7420/7410 User’s Manual Programmer’s Guide 5-10 Baud rate inaccuracy Divisor = 921600/Tar get Baud Rate. (Only Integer part) ENUM = 8 * (9 21600/Targer - Divisor) ( Round up or down) Inaccuracy = (Tar get Baud Rate – 921600 /(Divisor + (ENUM/8))) * 100% E.
UC-7420/7410 User’s Manual Programmer’s Guide 5-11 Special Note 1. UC-7420/7410’s kernel will store the “pressed k ey history” in a buffer. The maximum buffer size is 31 keys. If the buffer overflows, the firs t key of the 31 that was pressed will be drop ped, without sounding the buzzer.
6 6 Chapter 6 UC Finder The UC Finder utility is used to search the LAN or intranet for Moxa Universal Communicators. UC Finder c omes in ha ndy if you forget the IP address, for troublesho oting field problems, an d for testing. UC Fi nder works by sending a broadcast m essage over the L AN to search fo r UC-7420/7410 MAC addresses.
UC-7420/7410 User’s Manual UC Finder 6-2 Windows UC Finder The UC Finder utility is used to search the LAN or intranet for Moxa Universal Communicators. Installing the Sof tware 1. Once the Setup program starts running, click on Next to proceed. 2. Click on Next when the Select Addi tional Tool s window opens to proceed with the installation.
UC-7420/7410 User’s Manual UC Finder 6-3 3. Click on Next to install program files in the default dir ectory, or select an alternative location. 4. Click on Finish to complete the installation of UC Finder.
UC-7420/7410 User’s Manual UC Finder 6-4 Broadcast Search The Broadcast Search function is used to locate all UC-7420/ 7410 units that ar e connected to the same LAN as your Windows computer.
UC-7420/7410 User’s Manual UC Finder 6-5 3. When the search is complete, the same information is displayed in the UC Finder window. NOTE UC Finde r is designe d to determ ine the IP addres ses of all UC units conn ected to the sam e LAN the host that is running UC Finder.
A A Appendix A System Commands busybox (V0.60.4): Linux normal command utility collection File manager 1. cp c o p y f i l e 2. ls list file 3. ln make symbolic lin k file 4. mount mount and che ck file syst em 5. rm delete file 6. chmod change file owner & gr oup & user 7.
UC-7420/7410 User’s Manual System Commands A-2 Process 1. kill kill process 2. ps display now running process Other 1. dmesg dum p kernel log message 2. sty t o s e t s e r i a l p o r t 3. zcat dump .gz file context 4. mknod make device node 5. free display system memory usage 6.
B B Appendix B Windows Tool Chain Introduction UC-7420/7410’s Windows Too l Chain is a cross development environment that simulates the Linux root file system, allowing users to develop applications on a Windows PC. The followin g topics are c overed in t his appendi x.
UC-7420/7410 User’s Manual Windows Tool Chain Introduction B-2 Introduction UC-7420/7410’s Windows Too l Chain is a cross development environment that simulates the Linux root file system, allowing users to develop applications in a Windows env ironment.
UC-7420/7410 User’s Manual Windows Tool Chain Introduction B-3 Installation Procedure 1. Insert the CD i nto your PC’s CD-R OM drive, and r un tool-chainwindowscompilersetup.exe to start installation. Once the Setup program starts running, click on Next to proceed.
UC-7420/7410 User’s Manual Windows Tool Chain Introduction B-4 3. By default, the Local Package Directory is the same as on the CD-ROM: tool-chainwindowscompiler . Click on Next to pr oceed. Note: It may take anywhere from 5 to 20 minute s to check the packages in the CD-ROM after you click on Next .
UC-7420/7410 User’s Manual Windows Tool Chain Introduction B-5 y Base Categor y: List all packages that will be installed by default (along with any dependencies). If you view t he Base column fo r the Base cat egory, you s hould see eve ry package selected for installation.
UC-7420/7410 User’s Manual Windows Tool Chain Introduction B-6 6. Checkmark Create icon o n Desktop t o place a Moxa BASH Shell icon on your desktop, and then click on Finish . 7. Click on OK to close the Installation Complete window. Using the BASH Shell A command-line interface is used to develop app lications with the tool chain.
UC-7420/7410 User’s Manual Windows Tool Chain Introduction B-7 -rwxr—xr-x 1 stephen_ mkpasswd 53 Jan 10 22:03 moxa.bat -rw-r--r-- 1 stephen_ mkpasswd 3262 Jan 10 22:03 moxa.
UC-7420/7410 User’s Manual Windows Tool Chain Introduction B-8.
C C Appendix C Service Information This appen dix shows y ou how to co ntact Moxa for info rmation abo ut this and other pro ducts, and how to repo rt problems.
UC-7420/7410 User’s Manual Service Information C-2 MOXA Internet Services Customer satisfaction is our num b er one concern, and to ensure that customers receive the full benefit of our products, Moxa Internet Services has bee n set up to provide technical s upport, dri ver updates, product infor mation, and user’s manual upd ates.
UC-7420/7410 User’s Manual Service Information C-3 Problem Report Form MOXA UC-7420/7410 Customer name: Comp any: T el: Fax: Email: Date: 1. Moxa Product: UC-7 410-LX UC-7420-LX 2.
UC-7420/7410 User’s Manual Service Information C-4 Product Return Procedure For product repair, exc hange, o r refund, the customer m ust: Provide e vidence of origi nal purchase. Obtain a Product Return Agreement (PRA) from the sales representative or dealer.
An important point after buying a device Moxa Technologies UC-7420/7410 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Moxa Technologies UC-7420/7410 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Moxa Technologies UC-7420/7410 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Moxa Technologies UC-7420/7410 you will learn all the available features of the product, as well as information on its operation. The information that you get Moxa Technologies UC-7420/7410 will certainly help you make a decision on the purchase.
If you already are a holder of Moxa Technologies UC-7420/7410, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Moxa Technologies UC-7420/7410.
However, one of the most important roles played by the user manual is to help in solving problems with Moxa Technologies UC-7420/7410. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Moxa Technologies UC-7420/7410 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
