Instruction/ maintenance manual of the product 985117 Ariens
Go to page of 24
Owner/Oper ator Man ual Models 985114 - 16 HP 985115 - 8.5 HP 985117 - 13.5 HP 985119 - 12 HP 08499300 1/03 Printed in USA Pr of essional 2-Wheel T ractor.
2 ENGLISH 1. Operator Presence Control 2. Steering Brake Handlebar 3. Throttle Control 4. Ignition Switch 5. Hourmeter 6. Range Shift Handle (T wo Speed Axle) 7. Direction Control Le ver 8. P arking Brake Handle (Optional on 8.5HP) 9. Brak e Handle Cross Bar 10.
GB - 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Maintenance. . .
GB - 4 2. Check the saf ety inter lock system to mak e sure that it is functioning properly . Unit must not start unless direction control le v er is in neutral (N) and P ower T ak eoff (PT O) is disengaged (Off). Engine must stop if operator releases the handlebar with the direction control le v er or PT O engaged (On).
GB - 5 SAFETY DECALS AND LOCATIONS AL W A YS replace missing or damaged Saf ety Decals. Ref er to Figure 3 below f or Safety Decal locations. 1. D ANGER! T o Av oid Injur y or Death ! SAFETY FIRST REA.
GB - 6 2. SAF ETY FIRST 3. SAF ETY FIRST 4. CAUTION! Do not park on a slope unless wheels are chocked. SAFETY RULES Read, understand and f ollow all saf ety practices in Owner/Operator Manual bef ore beginning assembly . F ailure to follow instructions could result in personal injur y and/or damage to unit.
GB - 7 DO NO T touch unit par ts which might be hot from operation. Allow par ts to cool bef ore attempting to maintain, adjust or ser vice. NEVER place your hands or an y par t of your body or clothing inside or near any mo ving par t while unit is running.
GB - 8 K eep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open de vice.
GB - 9 ASSEMBL Y Install Hubs and Wheels F or Semi-Pneumatic Wheels: install bushings and wheel/hub assemblies onto tr actor axles. F or all other wheels: install hubs to axles and secure wheels to hubs with hardware pro vided. Install Kick Stand Slide kick stand into the righthand side of the low er brac ket on the rear hitch.
GB - 10 2. Connect the f orward end to the piv ot plate on the unit with a .375 x .75 cle vis pin, two .406 x .812 x .065 fl at washers and a .09 x .75 cotter pin. Inser t cle vis pin with cotter pin to the outside of adjustment brac ket (Figure 8). Right Hand Rod: 1.
GB - 11 CONTROLS AND FEATURES NO TE: Read the attachment(s) and unit manuals bef ore operating the equipment. Operate the unit only from the operator ’ s position, behind the handlebars. Ser vice the unit and attachment bef ore operating. Ref er to Controls and F eatures f or the f ollo wing.
GB - 12 Throttle Le ver The throttle le v er is used to control the engine speed. T o increase the engine speed, mov e the le v er up to the “ F AST ” position. T o decrease the engine speed, mov e the le v er down to the “ SLO W ” position. Choke Control The choke control is used to chok e a cold engine f or star ting.
GB - 13 3. Ensure the PT O control is in the “ OFF ” position and the gear shift le v er is in the “ NEUTRAL ” position. 4. If the engine is cold, apply the choke . See Engine Manual f or detailed instructions. 5. Set the throttle to the proper position.
GB - 14 TIPS FOR OPERATION Use slow gears when oper ating the tractor on rough ground, slopes, small areas , near b uildings or other obstacles. Use a slow gear and a f ast engine speed when oper ating a snowb low er , rotar y cultivator , or a mower in hea vy grass .
GB - 15 3. Clean the dipstick tube and the dipstic k (Figure 11). 4. Remov e the dipstic k, wipe it with a clean cloth or tow el and put it back in the tube . 5. Pull the dipstick out again and look at the oil. 6. If the oil le v el is below the lo w mark on the dipstick, add oil.
GB - 16 4. Place batter y on bench or other well-v entilated area. 5. Connect positiv e (+) lead of charger to positive (+) terminal, and negative ( – ) lead to negativ e ( – ) terminal. 6. Charge batter y according to charger and batter y manuf acturers ’ instr uctions.
GB - 17 T o adjust the rev erse clutch (Figure 13) : 1. Loosen the two nuts on the end of the fwd-re v control e xtension rod. 2. T ur n the adjusting nut so that the direction control le v er stops 15 degrees past v er tical to the rear . 3. Hold the adjusting nut and tighten the jam nut against it.
GB - 18 IMPORT ANT : Tighten and loosen the bolts in a cross sequence as shown in Figure 16. 4. Tighten all PT O brak e bolts until the springs are solid. Back all bolts up 1/2 turn (Figure 17). NO TE: Mak e sure the trunnion bloc k is on the shipper shaft and held in place by the dog.
GB - 19 IMPORT ANT : Tighten and loosen the bolts in a cross sequence as shown in Figure 16. 11. T ur n all of the jam nuts counterclockwise to loosen. 12. T orque bolts to 70 lbf-in in two stages. First tighten bolts to 20 lbf-in in patter n shown (Figure 16).
GB - 20 T R OUBLESHOOTING PROBLEM PROB ABLE CA USE CORRECTION Starter will not operate when ignition key is turned to “ S ” position. 1. Fwd-Re v le v er in “ FOR W ARD ” position. 2. PT O engaged. 3. Loose batter y cable(s). 4. Blown fuse . 5.
GB - 21 Attachment will not operate. 1. Gear shift le v er in “ NEUTRAL ” position. 2. Attachment jammed or damaged. 3. Attachment slip clutch out of adjustment or damaged. 4. Shipper shaft and clutch dog loose and out of adjustment. 1. Place gear shift le v er in Hi or Low position.
GB - 22 SERVICE P AR TS Be sure to alwa ys use gen uine Gra v ely par ts to keep your unit running like ne w . P ar t no . Qty Description 01554800 1 Batter y (Robin and K ohler Models) 04202200 1 Bat.
GB - 23 2-Y ear Limited W arranty Gra vely Division of Ariens Company (Gr av ely) hereby warrants to the original consumer purchaser that all Gra vely T wo-Wheel, Prof essional G, Pro , and ProMaster .
GRA VEL Y A Division of Ariens Company 655 West Ryan Str eet P .O. Box 157 Brillion, WI 54110-0157 920-756-2141 Fax 920-756-2407 www .gravely .com.
An important point after buying a device Ariens 985117 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ariens 985117 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ariens 985117 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ariens 985117 you will learn all the available features of the product, as well as information on its operation. The information that you get Ariens 985117 will certainly help you make a decision on the purchase.
If you already are a holder of Ariens 985117, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ariens 985117.
However, one of the most important roles played by the user manual is to help in solving problems with Ariens 985117. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ariens 985117 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
