Instruction/ maintenance manual of the product 938018 - SS722EC Ariens
Go to page of 24
Owner/Operator Man ual Models 938017 - SS5 22EC 938018 - SS7 22EC Sno-Thro ® 03392200 5/08 Printed in USA U.S. Patents 5758436 and 5966846 ENGLISH.
GB - 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Controls & Feat ur es . . . . . . . . . . . . . . . . 10 Oper a t ion . . . . . . . . . . . . . . . . . . . . .
GB - 3 • Record Unit Model and Serial numbers here. • Record Engine Model and Ser ial number here. PRODUCT REGISTRATION The Ariens d ealer must register the product at the time of purchase. Registering the product will help the company process warranty claims or contact you with the latest service information.
GB - 4 SAFETY ALERT S Look for these symbols to point out important safety precautions. They mean: Attention! Personal Safety Is Inv olved! Become Alert! Obey The Mess age! The safety alert symbols abo ve and signal words below are used on decals and in this manual.
GB - 5 SAFETY DECALS AND LOCATIONS AL WA YS replace m issing or dam aged Safety Deca l s. R e fe r to fi gu r e 2 be l o w fo r Sa f ety Decal locations. 1. DANGER! • Read operator ’s manual. • Allow operation only by properly trained adults, never children.
GB - 6 SAFETY RULES Read, understand, and follow all safety practices in Ow ner/Operator M anual before beginning assembly or operating. Failure to follow instructions could result in personal injury and/or damage t o unit. AL WA YS remov e key and/or wire from spark plug before assem bly , maintenance or service.
GB - 7 Understand: • How to operate all controls. • The functions of all controls. • How to STOP in an em ergenc y . Before starting engine, disengage control(s). Use only approved extension cords and receptacles when starting units equipped with electric starter .
GB - 8 If fuel is spilled on clot hing, change clothing immediately . Before tipping unit up onto housing, remov e fuel so no spills wil l occur. Ensure unit is secure and will not tip over during maintenance. AL WA YS keep prote ctive structures , guards, and panels in good repair , in place and securely fastened.
GB - 9 Discha rge Chute A ssembly 1. Remove bolt and nut from rear of discharge chute (figure 4). 2. T ip discharge chute up and install hardware just rem oved. Tighten hardware at r ear of discharge chute first, then sides. Discharge Chute Crank Asse mbly 1.
GB - 10 1. Auger Clutch Bail 2. Handlebar 3. Discharge Chute Crank 4. Handlebar Wing Knob 5. Sp ark Pl ug Acc ess C over 6. Discharge Chute Handle 7. Exhaust 8. Discharge Chute Deflector 9. Auger Housing 10. Auger 1 1. Ignition Switch 12. Fuel Level Indicat or 13.
GB - 1 1 CONTROLS AND FEATURES See figure 6 for controls and features locations. Ignition Sw itch Ignition switch is operated by a removable key that has two positions. 1. STOP 2. RUN Auger Clutch Bail Squeeze auger clutch bail against handlebar to engage auger.
GB - 12 Discharge Chute De flector AL WA YS position discharge chute deflector at a safe angle before starting engine. DO NOT throw snow any higher than necessary . Pull chute deflector handle u pward to throw snow lower . P ush chut e deflector handle downward to throw s now higher .
GB - 13 STOPPING IN AN EMERGENCY Immediately release au ger clutch bail t o stop unit in an emergency . S top engine, remove key and wait for all rotating parts to stop before leaving operator ’s position. ST ARTING AND SHUTTING OFF IMPORT ANT : Allow unit and en gine to adjust to the outdoor t emperature before clearing snow .
GB - 14 Tips f o r Op e r a t i o n Snow is best removed as soon as possible after a snow fall. T o clear an area, run unit in an overlapping series of paths. F or large ar eas, start in the middle and throw snow to each side, so s now is not cleared more than once.
GB - 15 SERV ICE PO SI T ION Place unit on a flat level surface. DRIVE BELT REPLACEME NT Remove (Fi gure 8) 1. Remov e cowl. 2. Disconnec t extension spring on idler arm/brake. 3. Remove auger drive pulley . 4. Remove old belt. Inst all (Figure 8) 1. Install new belt on drive pulley and idlers.
GB - 16 DISCHARGE CHUTE DEFLECTOR ADJUSTMENT If discharge chute def lector does not s tay in position while throwing snow , adjust chute by tightening fasteners (figur e 10). DRIVE BELT ADJUSTMENT Adjust Auger Control Cab le (Figure 1 1) 1. Meas ure bail spring length with auger clutch bail DISENGAGED.
GB - 17 3. Loosen belt finger and rotate until there is 1/32 – 1/16 in. (0.8 – 1.6 m m) gap between belt finger and drive belt. 4. Tighten belt finger . 5. Rechec k gap bet ween belt finger and drive belt. Adjust belt f inger until there is 1/32 – 1/16 in.
GB - 18 SHORT T ERM IMPORT ANT : NEVER spray unit with high pressure wa ter or st ore unit outdoors. Run with attachment clutch engag ed a few minutes after each use to free unit of any loose or melting snow . Inspect unit for v isible signs of wear, breakage or damag e.
GB - 19 T R OUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine wi ll not crank/ st art 1. Key not in RUN positi on. 2. Fuel tank empty . 3. Clogged fuel filter . 4. Faulty electric starter or wire connections. 1. T urn key to RUN position. 2. Fill fuel t ank.
GB - 20 SPE CIFICATIONS Model Num ber 938017 938018 Description SS522EC SS722E C Engine - T ecumseh (Two-Cycle) TH139SA TH139SP Engine Power – hp (kW) at Maximum RPM 5 (3.73) 7 (5.22) Fast Idle S peed – RPM (min -1 ) 3950 ± 150 Displacement – in.
.
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® MOWE R | BYNORM ® | EVERRIDE ® | GREAT DA NE ® Snow_2008 22 Three-Y ear Limi ted Sno-Thro ® Wa r r a n t y Ariens Company (Ariens).
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® | BYNORM ® | EVERRIDE ® | GREA T DANE ® Snow_2008 23 Limitations • Batteries are w arranted only for a peri od of 12 m onths after date of purcha se, on a p rorat ed basis. For the first 90 da ys of the war ranty peri od, a defective battery will be replaced free of charge.
Ariens Company 655 West Ryan St reet Brillion, W I 541 10-1072 920-756-2141 Fax 920-756-2407 www .ariens.com.
An important point after buying a device Ariens 938018 - SS722EC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ariens 938018 - SS722EC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ariens 938018 - SS722EC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ariens 938018 - SS722EC you will learn all the available features of the product, as well as information on its operation. The information that you get Ariens 938018 - SS722EC will certainly help you make a decision on the purchase.
If you already are a holder of Ariens 938018 - SS722EC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ariens 938018 - SS722EC.
However, one of the most important roles played by the user manual is to help in solving problems with Ariens 938018 - SS722EC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ariens 938018 - SS722EC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
