Instruction/ maintenance manual of the product 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC Ariens
Go to page of 22
Owner/Operator Man ual Models 938017 - SS5 22EC 938018 - SS7 22EC 938019 - SS5 22 9381 17 - SS 522EC Sno-Thro 00447600 7/05 Printed in USA T ransfe r model & serial number label from product registration here. Coller l’autocollant du modèle et du numéro de série dans cet encadré.
GB - 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Controls & Feat ur es . . . . . . . . . . . . . . . . . 9 Oper a t ion . . . . . . . . . . . . . . . . . . . .
GB - 3 DISCLAI MER Ariens reserves the right to d iscontinue, make changes to, and add improvements upon its product s at any time without public notice or obligation. The des criptions and specifications contained in this manual wer e in effect at printing.
GB - 4 REQUIRED OPERATOR T RAINING Original purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by som eone other than original purchaser; loaned, r ented or sold, AL WA YS provide this manual and any needed safety training before operation.
GB - 5 SAFETY RULES Read, understand, and follow all safety practices in Ow ner/Operator Manual b efore beginning assembly or operating. Failure to follow instructions could result in personal injury and/or damage t o unit. AL WA YS remove key and/or wire from spark plug before assem bly , maintenance or service.
GB - 6 Fumes from engine exhaust can cause injury or death. DO NOT r un engine in an enclo sed area. Always provide good ventilation. AL WA YS disengage attachment, stop unit and engine, remov e key and allow moving parts to st op before leaving operator ’s position.
GB - 7 Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner . Always place containers on the gr ound away from your vehicle before filling. When practical, remov e gas-powered equipment from the truck or trailer and refuel it on the ground.
GB - 8 Discha rge Chute As sembly 1. Remove bolt and nut from rear of discharge chute (figure 4). 2. T ip discharge chute up and inst all hardware just rem oved. Tighten hardware at r ear of discharge chute firs t, then sides. Discharge Chute Crank Assembly (938017, 0 18, 1 17) 1.
GB - 9 1. Auger Clutch Bail 2. Handlebar 3. Discharge Chute Crank (938017, 018, 11 7 ) 4. Handleba r Wing Knob 5. Spark Plug Access Cover 6. Discharge Chute Handle 7. Exhaust 8. Discharge Chute Deflector 9. Auger Housing 10. Auger 1 1. Ignition Switch 12.
GB - 10 CONTROLS AND FEATURES See figure 6 for controls and features locations. Ignition Sw itch Ignition switch is operated by a removable key that has two positions. 1. STOP 2. RUN Auger Clutch Bail Squeeze auger clutch bail against handlebar to engage auger.
GB - 1 1 IMPORT ANT : DO NOT force a frozen discharge chute. St art engine and run for 3-5 minutes to thaw . If still froz en, t ak e to a warm place until controls are free. Discharge Chute De flector AL WA YS position discharge chute deflector at a safe angle before starting engine.
GB - 12 STOPPING IN AN EMERGENCY Immediately release au ger clutch bail to s top unit in an emergency . S top engine, remove key and wait for all rotating parts to stop before leaving operator ’s position. ST A RTING AND SHUTTING OFF IMPORT ANT : Allow unit and engine to adjust to the outdoor t emperature before clearing snow .
GB - 13 Tips f o r O p er a t i on Snow is best removed as soon as possible after a snow fall. T o clear an area, run unit in an overlapping series of paths. F or large ar eas, start in the middle and throw snow to each side, so s now is not cleared more than once.
GB - 14 SERV ICE PO SI T ION Place unit on a flat level surface. DRIVE BELT REPLACEME NT Remove (Fi gure 8 ) 1. Remove cowl. 2. Disconnect extension spring on idler arm/brake. 3. Remove auger drive pulley . 4. Remove old belt. Inst all (Figure 8) 1. Install new belt on drive pulley and idler s.
GB - 15 DISCHARGE CHUTE DEFLECTOR ADJUSTMENT If discharge chute def lector does not s tay in position while throwing snow , adjust chute by tightening fasteners (f igure 10). DRIVE BELT ADJUSTMENT Adjust Auger Control Cab le (Figure 1 1) 1. Measure bail spring length with auger clutch bail DISENGAGED.
GB - 16 3. Loosen belt finger and rot ate until there is 1/32 – 1/16 in. (0.8 – 1.6 m m) gap between belt finger and drive belt. 4. T ighten belt finger . 5. Recheck gap bet ween belt finger and drive belt. Adjust belt f inger until there is 1/32 – 1/16 in.
GB - 17 SHORT T ERM IMPORT ANT : NEVER spray unit with high-pressure water or store u nit outdoors. Run with attachment clutch engag ed a few minutes after each use to free unit of any loose or melting snow . Inspect unit for v isible signs of wear, breakage or damag e.
GB - 18 T ROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine wi ll not crank/ star t 1. Key not i n RUN position. 2. Fuel tank empty . 3. Clogged fuel f ilter . 4. Faulty electric starter or wire connections. 1. T u rn key to RUN po sition. 2. Fill f uel tank.
GB - 19 SPECIFI CATIONS Mod e l Numb er 938017 938018 938019 938 1 17 Description SS52 2EC SS722EC SS522 SS522EC Engine - T ecumseh (Two-Cycle) TH139SA TH139SP TH139SA TH139SA Power Max – HP (Kw/m in -1 ) 5 (3.73) 7 (5.22) 5 (3.73) Fast Idle Speed – RPM (min -1 ) 3950 ± 150 Displacemen t – in.
Ariens Com pany • 6 55 W . Ry an St, P .O. Bo x 157 • Brillion, WI 541 10-0 157• (920) 756-2141 • www.ariens.com AL W2-6 2905 Ariens Limited Warranti es 2-Year L imited Lawn an d Garden Consum.
Ariens Com pany • 6 55 W . Ry an St, P .O. Bo x 157 • Brillion, WI 541 10-0 157• (920) 756-2141 • www.ariens.com AL W 2-62 905 Exceptions, L imitations, Ex clusions These warran tie s are subj.
Ariens Company 655 West Ryan Street P .O. Box 157 Brillion, WI 541 10-0157 920-756-2141 Fax 920-756-2407 www .ariens.com.
An important point after buying a device Ariens 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ariens 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ariens 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ariens 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC you will learn all the available features of the product, as well as information on its operation. The information that you get Ariens 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC will certainly help you make a decision on the purchase.
If you already are a holder of Ariens 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ariens 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC.
However, one of the most important roles played by the user manual is to help in solving problems with Ariens 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ariens 938017 - SS522EC, 938018 - SS722EC, 938019 - SS522, 938117 - SS522EC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
