Instruction/ maintenance manual of the product 932310 - 624 Ariens
Go to page of 26
Owner/Operator Man ual Models 932102 - 520 932103 - 624 932310 - 624 Sno-Thr o ® 03243800D 5/02 Supersedes 03243800,A, B, C Printed in USA ENGLISH FRANÇAIS ESP A Ñ OL T r ansfer model & serial number label from product registration here. Coller l ’ autocollant du mod è le et du num é ro de s é rie dans cet encadr é .
2 5/30/02 MODEL CERTIFICA TE OF CONFORMITY ISSUED BY THE MANUF ACTURER CERTIFICA T DE CONFORMIT É DU MOD È LE D É LIVR É P AR LE F ABRICANT MODELL-K ONFORMIT Ä TSBESCHEINIGUNG A USGESTELL T DURCH.
3 5/30/02 Stated Sound P ower Le vels are established f ollowing Anne x V “ Inter nal Control of Production ” of directive 2000/14/EC and assessment procedure EN-ISO 3744:1995.
4 ENGLISH 1. Attachment Clutch Bail 2. Chute Control Lev er (932102) Chute Crank (932103, 310) 3. Muf fl er Guard 4. Chute De fl ector 5. Discharge Chute 6. Housing 7. Throttle 8. Spark Plug and Wire 9. Oil Fill and Dipstick 10. Fuel T ank and Cap 11.
5 1 2 4 5 6 7 8 9 10 11 13 14 15 16 17 932102 OS2080 OS1911 Figure 1 1 2 3 4 5 6 7 8 9 10 12 13 16 17 14 15 11 OS1746 OS2071 932103 932310 18 19 17 18 19 3.
GB - 6 Controls and Features . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Operation . . . . . . . . . . . . . . . . . . . . . . .
GB - 7 DELIVERY Customer Note: If you ha ve purchased this product without complete assembly and instruction by your retailer , it is your responsibility to: 1.
GB - 8 SAFETY DECALS AND LOCATIONS AL WA YS replace missing or damaged Safety Decals. Refer to fi gure below f or Safety Decal locations. 1. D ANGER! 2. D ANGER! SAFETY 3. HO T SURF A CES! DANGER / PELIGRO ROT A TI NG PARTS Stop engine & remove ignition ke y before clearing.
GB - 9 ASSEMBLY SAF ETY RULES Read, understand, and follo w all safety practices in Owner/Operator Manual bef ore assembling. F ailure to follo w instructions could result in personal injury and/or damage to unit. AL WA YS remove k ey and/or wire from spark plug before assemb ly .
GB - 10 Rotating impeller can cause serious injur y . DO NO T unclog unit while engine is running. When leaving operator ’ s position for any reason, AL WA YS disengage auger, stop unit and engine, remov e ke y and allow mo ving par ts to stop . Before starting engine, disengage control(s).
GB - 11 MAINTENANCE AND SERVICE SAFETY RULES Before c leaning, removing clogs or making any inspections, repairs, etc.: disengage clutch(es), stop unit and engine, remove key , allow mo ving parts to stop. Allow hot parts to cool. Before tipping unit up onto housing, remo ve enough fuel so no spills will occur .
GB - 12 Discharge Chute (932102) 1. Grease discharge chute ring if not already greased (Figure 4b). 2. Remo ve mounting hardw are from top of engine. 3. Slide discharge chute o ver opening on housing and under the retaining clip . 4. Secure chute support brack et to studs on top of engine with mounting hardware just remov ed.
GB - 13 3. Ensure Z bend end of clutch cab le is connected to hole in tab on right side of clutch bail. Check A uger Gearcase Oil Check oil le vel in auger gearcase (see Maintenance Section). Fill Engine Crankcase IMPORT ANT : Engines are shipped without oil in crankcase.
GB - 14 Throttle The Throttle controls the engine speed. T o increase or decrease the engine speed, adjust to: 1.F ast (normal or warm star ts) 2.P ar t-Throttle 3.Slow (cold weather starts) 4."Stop" (engine is off) Recoil Starter Handle IMPORT ANT : DO NO T let handle snap back against star ter .
GB - 15 5. Insert key into ignition s witch and push into R UN position. DO NO T twist ke y after inser ting it. 6. Gr asp star ter handle and pull rope out slowly until it pulls harder . Let rope rewind slowly . 7. Pull rope with a r apid continuous full arm stroke .
GB - 16 Secure unit chassis to transport vehicle. NEVER secure from rods or linkages that could be damaged. DO NO T transpor t machine while engine is running. SERVICE P OSITION Place unit on a fl at lev el surf ace. Before tipping unit up onto housing, remov e enough fuel so no spills will occur .
GB - 17 T o ensure adequate lubr icant lev el: 1. Remo ve fi ller plug (Figure 5). Lubricant must be at least up to bottom of lubricant fi ller hole with unit resting on a lev el surface . 2. Add lubricant if required. Allow oil to drain to lev el of plug and replace plug.
GB - 18 ATTACHMENT DRIVE BELT REPLACEMENT Remove old attac hment drive belt: 1. Shut off engine , remov e key , disconnect spark plug wire and allow unit to cool completely . 2. Remo ve belt co ver (Figure 4a, 4b). 3. If equipped with chute cr ank, remove spring clip from chute crank and remov e chute crank.
GB - 19 ATTACHMENT CLUTCH / BRAKE ADJUSTMENT 1. Remo ve belt co ver . 2. Chec k belt alignment (Figure 9). Engine sheav e and attachment pulley must align v er tically . Also, belt must be centered in the idler pulley . T o move pulley or shea ve: a. Loosen set screw .
GB - 20 DISCHARGE CHUTE If Chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on spring (Figure 10). If the de fl ector cap does not remain set in position tighten nut on right side of cap until proper drag is obtained.
GB - 21 A UGER EDG E REPLACEMENT Over time the rubber edges of the auger will wear . Contact y our Ariens Dealer for replacement. IMPORT ANT : Replace rubber edges before metal auger begins to wear . NO TE: After replacement of auger rubber edges, adjust scraper b lade.
GB - 22 T o obtain a complete par ts manual, fi nd your model and serial number . Then go to www .ar iens.com or call 1-800-678-5443. Engine stops. 1. Out of fuel. 2. Mechanical jam in blower rake or impeller . 3. P olluted fuel supply . 4. F aulty spark plug.
GB - 23 SPECIFICATIONS Model Number 932102 932103 932310 Description 520 624 624 Engine - T ecumseh HSSK50- 67409T OHSK60- 71505D OHSK60- 71504D P ower Max - HP (Kw/min -1 ) 5 (3.73) 6 (4.47) F ast Idle Speed - RPM (min -1 ) 3600±150 Displacement - in (cc) 11.
GB - 24 3 Y ear Limited Sno-Thro W arranty Ariens Company warrants to the original purchaser that consumer products manufactured by Ariens Company will be free from def ects in material and workmanshi.
GB - 25 DURA-CLEAN ™ Au g e r Limited Lifetime W arranty Ariens Company hereby warr ants to the original purchaser that the r ubber components of the DURA-CLEAN ™ Auger man ufactured by Ariens Company will be free from defects in material and workmanship and will not wear out f or the life of the sno- thro , except as noted below .
Ariens Company 655 West Ryan Str eet P .O. Box 157 Brillion, WI 54110-0157 920-756-2141 Fax 920-756-2407 www .ariens.com.
An important point after buying a device Ariens 932310 - 624 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ariens 932310 - 624 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ariens 932310 - 624 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ariens 932310 - 624 you will learn all the available features of the product, as well as information on its operation. The information that you get Ariens 932310 - 624 will certainly help you make a decision on the purchase.
If you already are a holder of Ariens 932310 - 624, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ariens 932310 - 624.
However, one of the most important roles played by the user manual is to help in solving problems with Ariens 932310 - 624. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ariens 932310 - 624 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
