Instruction/ maintenance manual of the product 3300 Mitel
Go to page of 22
7/4/2004 Page 1 of 22 Mitel PBX interface with Conferencing Server Configuration Notes Note: This document section is maintained by Mitel Networks When referring to any information in this document please also check the Additions & Correction section on the last page for up dates.
7/4/2004 Page 2 of 22 Mitel PBX interface with Conferencing Server Configuration Notes Mitel PBX interface with Confere ncing Server Configuration Notes ........................ 1 Introduction ..........................................................
7/4/2004 Page 3 of 22 Introduction This document describes the configuration of Mitel Networks PBX’s to correctly interface to the Interactive Group Communication System by VCon. For more information on the configuration o f the IGC, please refer to Mitel 3300 - RemoteAbility IGC Integration Specifications V1 .
7/4/2004 Page 4 of 22 ANI/DNIS/ISDN Number Delivery Yes Link Descriptor Assignment Number: 4 Address for Message Control: A BER - Maintenance Limit, 10** - n: 4 BER - Service Limit, 10** - n: 3 Data C.
7/4/2004 Page 5 of 22 MSDN - DPNSS - DASSII Trunk Circuit Descriptor Number Card Type Dual Seizure Priority Far End Connection Signalling Protocol 4 UNIVERSAL T1 Incoming Local Office MSDN - DPNSS Tru.
7/4/2004 Page 6 of 22 • Attach VCon IGC server T1 link to NSU, DSU or Embedded PRI card o Configure hardware for Line Termination through jumpers or D IP switch – please refer to the Technician’.
7/4/2004 Page 7 of 22 ANI/DNIS/ISDN Number Delivery Yes Link Descriptor Assignment Number: 4 Address for Message Control: BER - Maintenance Limit, 10** - n: 4 BER - Service Limit, 10** - n: 3 Data Cal.
7/4/2004 Page 8 of 22 Digital E and M Trunk Circuit Descriptor Assignment Number: 4 Call Collision Han dling: AT&T AT&T Call Collision Handling: Backoff Ignore Far End Disconnect: No Release A.
7/4/2004 Page 9 of 22 D igital Trunk Assignment Cabinet: 6 Shelf: 1 Slot: 1 Circuit: 1 Card Type: UNIVERSAL T1 Trunk Number: 6101 Trunk Service Number: 4 DTS Service Number: Circuit Descriptor Number:.
7/4/2004 Page 10 of 22 2 6102 3 6103 4 6104 5 6105 6 6106 7 6107 8 6108 9 6109 10 6110.
7/4/2004 Page 11 of 22 Create Digit Modification Assignment - in this example, we are using Digit Modification number 4 , and there are no digits to absorb or to insert Digit Modification Assignment D.
7/4/2004 Page 12 of 22 SX200 with ISDN • Attach VCon IGC server to PRI card with straight through cable o Configure hardware for Line Termination. Please refer to SX200 Technician ’s Handbook for more information.
7/4/2004 Page 13 of 22 Example of T1 PRI Programming on SX200 Refer to SX200 EL/ML Technicians Handbook , Programming a PRI, for System Configuration, Class of Service Options and System Options/System Timers. Form 13 Assign T1 E&M circuit descriptor to the ISDN trunk.
7/4/2004 Page 14 of 22.
7/4/2004 Page 15 of 22.
7/4/2004 Page 16 of 22 Define the incoming ISDN trunk as a Dial In trunk in form 15.
7/4/2004 Page 17 of 22 Assign the ISDN trunks to a trunk group in Form 16.
7/4/2004 Page 18 of 22 Select a T1 Link Descriptor for the ISDN trunks in form 42.
7/4/2004 Page 19 of 22.
7/4/2004 Page 20 of 22 Assign the ISDN link descriptor to slot 6 a nd/or slot 8 on the PRI card bay, Form 43 Form 44, Network Sync - To be determined by qualified Technician SX200 with T1/D4 • Attach VCon IGC server to SX200 with cross over cable. • Program trunks for T1/D4 .
7/4/2004 Page 21 of 22 T1 Crossover cable wiring Specifications [RJ45 Connector] Supplied with RemoteAbility system. Connector A Pin Connector B Pin 1 4 2 5 4 1 5 2.
7/4/2004 Page 22 of 22 Addition & Corrections The change I had to make was with the ANI/DNIS insertion in digit mod with T1/D4 trunks : The doc says above to insert **6135922122** The correct form.
An important point after buying a device Mitel 3300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Mitel 3300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Mitel 3300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Mitel 3300 you will learn all the available features of the product, as well as information on its operation. The information that you get Mitel 3300 will certainly help you make a decision on the purchase.
If you already are a holder of Mitel 3300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Mitel 3300.
However, one of the most important roles played by the user manual is to help in solving problems with Mitel 3300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Mitel 3300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
