Instruction/ maintenance manual of the product 926042 Ariens
Go to page of 26
Quick St art Guide Pr o - T r ack 28 (92604 2 s /n 75000 & up) • Step 1: Unfold Handlebar • Step 2: Install D is char ge Chute • Step 3: Install C hute Contr ol Assembly • Step 4: Install .
St ep One: Unf old Handlebar 1. Remove the lower and loosen the upper hardw are on the handlebar assembly . 2. Loosen the hard war e on the shift rod. 3. Put the speed selector lever in the second reverse position. 4. Rotate the handlebar into operating position.
St ep T wo: Inst all Discharg e C hute 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardw are from auger housi ng. 3. Install discharge chute over opening in the auger housing. Finger tighten the mounting hardwar e removed above.
St ep Three: Ins tall Chute Con trol Assembly 1. Remove the gear cover from top of chute pedesta l. 2. Release the lock teeth on the gear assembly with your finger and rotate the discharge chute so it points straight ahead. NOTE : Make sure alignment markers are lined up when discharg e chute is pointing straight ahead .
St ep Three: Ins tall Chute Con trol Assembly Cont. 3. Remove the rubber gromm et from the control panel. 4. Make sure the chute control cable is routed betw een the lower handlebar and the bottom of the control panel, insert contro l assembly into slot in control panel from below and install assembly into nylon bushing in control panel.
St ep Four: Inst all Discharg e Chute R od NOTE : T o ensure the discharge chute follows its full range of travel , make sure the control lever is centered i n the slot and pointing straight up before i nstalling the chute rod.
St ep F our: Ins t all Dischar ge Chut e Rod Con t. 4. Hook the chute contro l cable onto the chute rod . IMPORT ANT : The chute control cable hook will prevent the cable from contacting the engine or muf fl er guard. Make sure the cable stays connected whi le unit is in operation.
St ep Five: Inst all R e mote Deflect or Control Cable 1. Connect the barr el cable end to the chute defl ect or cable anchor before clipping t he cable to the discharge chute cable bracket . 2. Route deflector r emote cable along the lef t side of the chute pedestal.
St ep Six: Check Functio n of Dual Handle In t erlock Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever . Attachment clutch s hould remain engaged until traction clutch lev er is released, then both clutches must disengage.
St ep Sev en: Check T r ack T ension Check tracking of unit with the dif ferential locked, and tension of tracks (see T rack T ension Adjustment in Owners Manual.
St ep Eight: Adjus t Skid Shoes IMPORT ANT : Skid shoes should be adjus ted as conditions require. Allow 1/8 in. (3mm) between scraper blade and hard smooth surfac es. Allow 7/8 in. (22 mm) betw een scraper blade and uneven or grav el surfaces . (S ee Skid Shoes in O wners Manual) .
Check oil level in auger gearcase (see Check Auger Gearcase in Owner s Manual). St ep Nine: Check Aug er Gear case Oil.
IMPORT ANT : T he engine is shipped with oil in crankcase. Refer t o Engine Manual for detailed instructions. St ep T en: Check Engine Cr ank case Oil.
Fill fuel tank. DO NO T OVERFILL! See FILLING FUEL T ANK in Owners Manual. St ep Elev en: Fill Eng ine F uel T ank.
St ep T w elv e: St arting the Engine.
St arting Engine / St ep A: Thr ottle Move the throttle control lever to the fast position. Operate the engine with the thrott le control lever in the fast position.
St arting Engine / Step B : Fuel V alv e T urn the fuel shut - of f valve to the ON position..
St arting Engine / Step C : Ke y Insert the key and turn to the ON/ST AR T position..
St arting Engine / Step D : Chok e T urn the choke control knob to the choke position. NOTE: Choke is usually unnecessary when restarting a warm engine.
St arting Engine / Step E : Prime Push the primer two times. Be sure to cover vent hole on primer bulb. NOTE: Priming is usually unnecessary when restarting a warm engine.
St arting Engine / Step F : (Manual St art) Firmly hold the starter cord handle. Pull the starter cord han dle slowly u nt i l re s is tance is felt, then pull rapidly . NOTE : If the engine does not start a fter repeated attempts , go to BRIGGSandSTRA TTON.
St arting Engine / St ep F : (Electric St art) First conn ect the extension cord to th e power cord rec eptacle and then into a wall receptacle. If an additional ext ension cord is requir ed, make sure it is a 3 - wire grounded extens ion cord.
St arting Engine / St ep G: (Electric St art) Depress the push button. After you start the engine, first disconnect the extension cord from the wall receptacle and then from the power cord receptacle.
St arting Engine / Step H: W arm up Allow the engine to warm up for several minutes. Then, slowly move the choke control knob to the run position..
St ep Thirt een: St opping the Engine T urn the key t o the off position or move throttle control lever to slow and then to the stop position (completely right). Remove the key . Keep away from reach of children. After engine stops, turn the fuel s hut - of f valve to the closed (vertical) position.
Additional R esour ces • R ef er t o Owner s Manua l and Engin e Manual • Cont act Ariens Com pan y www .ariens.c om Phone: 920 -756-4688 E- mail: inf o@ariens.c om • F or issues concerning engine, pl ease con tact Brig g s and Str at t on www .
An important point after buying a device Ariens 926042 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ariens 926042 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ariens 926042 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ariens 926042 you will learn all the available features of the product, as well as information on its operation. The information that you get Ariens 926042 will certainly help you make a decision on the purchase.
If you already are a holder of Ariens 926042, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ariens 926042.
However, one of the most important roles played by the user manual is to help in solving problems with Ariens 926042. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ariens 926042 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
