Instruction/ maintenance manual of the product K36 0005R Milnor
Go to page of 21
Published Manual Number/ECN: H28 0010/2001074N • Publishing System: TPAS • Access date: 2/14/01 • Document ECN's: Latest Available Kit Instruction— K28 0010 K36 0005 K36 0005R PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.
Please Read A bout the Manual Identif y ing Information on the Cover The front cover d isplay s pert inent id entify ing in form ation fo r this m anual.
1.
MSSM020 4AE/833 2BV (1 of 1) È V-BELT TENSION ADJUSTMENTS FOR 30" AND 36" B-TYPE MACHINES AND 42" Q-TYPE MACHINES This instruction i s to be used for adjus ting the belt tension on the.
MSSM0301AE/9126B V È V-BELT TENSION ADJUSTMENTS This instruction is to be used for adjusting the belt tension on the following machine models: A belt tension testing device (Milnor ® part number 30T001) and a straight edge are required when using these instructions.
MSSM0301AE/9126BV (1 of 1) È V-BELT TENSION ADJUSTMENTS This instruction is to be used for adjusting the belt tension on the following machine models: A belt tension testing device (Milnor ® part number 30T001) and a straight edge are required when using these instructions.
M S S M A40 5 A E / 873 7 B V È V-BELT TENSION ADJUSTMENTS FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS This instruction is to be used for adjusting the belt tension on the followi.
MS SMA405 AE/ 8737 BV (1 of 2) È V-BELT TENSION ADJUSTMENTS FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS This instruction is to be used for adjusting the belt tension on the follow.
Ë Tensioning Banded Belts Ï 48032BHE, BTG , BTH 48 036QHE, QTG, QT Belt Deflect. (inches) Initial Tension (l bs.) (r ef.) Initial Tension (lbs.) (re f.) Belt Deflect (in.) Initial Tension (lbs. ) (re f.) Initial Tension (lbs. ) (re f.) WASH/ 2 SPEED WASH 9/32 6.
Ë Tensioning Banded Belts Ï 48032BHE, BTG , BTH 48 036QHE, QTG, QT Belt Deflect. (inches) Initial Tension (l bs.) (r ef.) Initial Tension (lbs.) (re f.) Belt Deflect (in.) Initial Tension (lbs. ) (re f.) Initial Tension (lbs. ) (re f.) WASH/ 2 SPEED WASH 9/32 6.
9.
M S S M 030 3 A E / 845 1 B V È MAIN BEARING AND SEAL REPLACEMENT FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard ® , dye machines , et c.
MSSM 0303 AE/8451 BV (1 of 5) È MAIN BEARING AND SEAL REPLACEMENT FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard ® , dye machines , et c.
inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support.
inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support.
Ê Replacing the Bearing Housing, Seal Sleeve, and Seals (Front or Rear) 1 . With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make cer- tain they are unblocked.
Ê Replacing the Bearing Housing, Seal Sleeve, and Seals (Front or Rear) 1 . With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make cer- tain they are unblocked.
Ê Measuring Unmounted Clearance and Setting Bearing (Front or Rear) The bearings used on Milnor ® washer and dye extractors are the very best anti-friction devices available for these applicati ons. However, the anti-frict ional characteristi cs of the bearings will be reduced if they ar e not proper- ly inst alled.
Ê Measuring Unmounted Clearance and Setting Bearing (Front or Rear) The bearings used on Milnor ® washer and dye extractors are the very best anti-friction devices available for these applicati ons. However, the anti-frict ional characteristi cs of the bearings will be reduced if they ar e not proper- ly inst alled.
Ê Tightening Bearing(s) (Front and/or Rear) 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and lock- nut(s).
Ê Tightening Bearing(s) (Front and/or Rear) 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and lock- nut(s).
An important point after buying a device Milnor K36 0005R (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Milnor K36 0005R yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Milnor K36 0005R - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Milnor K36 0005R you will learn all the available features of the product, as well as information on its operation. The information that you get Milnor K36 0005R will certainly help you make a decision on the purchase.
If you already are a holder of Milnor K36 0005R, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Milnor K36 0005R.
However, one of the most important roles played by the user manual is to help in solving problems with Milnor K36 0005R. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Milnor K36 0005R along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
