Instruction/ maintenance manual of the product 921032 Ariens
Go to page of 27
Quick St art Guide Delux e 30 (921 032 s/n 101 & up) • Step 1: Assemble Handlebars • Step 2: Connect Headlight Wire Harness • Step 3: Install Discharge Chute • Step 4: Install Discharge Ch.
Step On e: Assemble Handlebar s (Unf old Lower Handlebar) IMPORT A NT : Be sure to block wheels or secure unit so it does not move during assembly . 1. Rotate lower handlebar out from unit so low er handlebar mounting holes align w ith mounting holes on the unit f rame.
Step On e: Assemble Handlebar s (A t tach Upper Hand lebar Assembly) 1. Attach upper handlebar assembly to lower handlebar using two sets of the handleb ar hardware. One set to att ach each side of the handlebar s. NOTE: DO NOT tighten hardw are. Allow upper handlebar assembly to hang from the lower handlebar s for the nex t st ep.
Step On e: Assemble Handlebar s (A t tach Con tr ol Cables) 1. Hook spring end of attachme nt c ontrol cable to the clutch arm. 2. Hook spring end of the traction c ontrol cable to the cable eyelet on back of frame. NOTE: Make sure cable remains in groove of pulley .
Step On e: Assemble Handlebar s (Unf old Upper Handlebar) Assembly) 1. Rotate handlebar into operating position. NOTE: Be careful not to damage cable spring hooks when rotating handlebar upward. 2. Install the remaining handlebar hardware attaching the upper handlebar as sembly to the low er handlebar .
Step T wo: Connect Headligh t Wir e Harness NOTE: The headlight w ire harness comes attached to the upper handlebar as sembly . 1. Route the wire harness along the interior of the right side handlebar . 2. Connect to the engine elec trical plug. 3. Press cable anc hor into mounting hole in the frame near the engine electrical plug.
Step Thr ee: Ins t all Discharg e Chut e 1. Grease underside of discharge chute ring (if not already greased). 2. Remov e mounting hardware from auger housing. 3. Install discharge c hute over opening in the auger housing. Finger tighten the mounting hardware remov ed above.
Step F our: Ins t all Discharg e Chut e Cr ank 1. Remov e the gear cov er from top of chute pedest al. 2. Insert the short end of the c hute crank into the hole in the front of the control panel. NOTE: Be careful not to damage ny lon bushing when attaching crank to the dash.
Step Fiv e: Inst all Remot e Deflect or Con trol Cable NOTE: Connect the barrel cable end to the chute deflector cable anchor before clipping the cable to the discharge chute cable bracket. 1. Route deflector remote cable along the left side of the chute pedestal.
Step Six: Ins t all Skid Shoes 1. Remove hardware from skid shoes. 2. Install hardware through blower housing and skid shoe as shown. 3. Adjust skid shoes, see Skid Shoes in Owners Manual.
St ep Sev en: Check Function of Dual Handle In terlock Without the en gine running , press dow n (engage ) both clu tch levers. Relea se attachment clutch lever . Attachment clu tch should remain engage d until traction clutch lever is released , then both clutches must d isenga ge.
St ep Eigh t: Check Tir e Pr essur e Check tire pressu re and adjust to the pressure listed on tire sidew all..
Check oil le vel in auger gearcase (see Check Auger Gearcase in Ow ners Manual). St ep Nine: Check Aug er Gear case Oil.
IMPORT A NT : The engin e is shipped with 5W-30 oil in crankcase. Refer to engine manual for detailed instructions. St ep T en: Check Engine Cr ank case Oil (Ariens AX).
Fill fuel tank. DO N OT OVERFILL! See FILLING FUEL T ANK in Ow ners Manual. St ep T welv e: Fill Engine Fuel T ank (Ariens AX).
St ep Thirt een: St arting the Engine (Arie ns AX).
St arting Engine / Step A: Chok e T urn throttle al l the way up. T urn choke ON..
St arting Engine / Step B: R ock er Swit ch Push rocker switch to RUN position..
St arting Engine / Step C: Fuel Shut Off V alv e T urn fuel petcock to ON position..
St arting Engine / Step D: K ey Install Safety K ey Switch. Insert ignition key into slot but DO NOT turn the key . Be sure ignit ion key snaps into place.
St arting Engine / Step E: Prime Prime sy stem: 3 primes maxi mum. DO NOT over prime system. Make sure to cover the v ent hole on primer bulb before the primer bulb is compressed. Hold the primer bulb in the compressed pos ition for one full second each time you press it.
St arting Engine / Step F: (Manual St art) Grasp rope handle. Pull slowly until resistance is felt, then pull rope firmly and quickly to start engine and avoid kickback.
St arting Engine / Step F: (Electric St art) Use a 3-wire ex tension cord and plug cord into starter motor adaptor first. Then plug cord into wall receptacle. Use appropriately siz ed extension cord (10A WG or larger) to prevent damage to electric starter .
St arting Engine / Step G: (Electric St art) Press and hold starter button. Note : Do not hol d the electric starter button down for more than 5 seconds.
St arting Engine / Step H: W arm up Allow the engine to warm up for 1- 2 minutes, move the choke control to the CHOKE OFF position..
St ep F ourt een: St opping the Engine (Ariens AX) Under normal condition s: 1. T urn throttle dow n. 2. Push rocke r sw itch to STOP position. 3. Pull safety key OUT . T o s top engine in a n emergency , fli p the Rocker Sw itch to the ST OP p osition, OR Pull Safety Key from Engine.
Additional R eso ur ces • R ef er to O wner s Manual and Engine Manual • Con t ac t Ariens Compan y www .ariens.com Phone: 920- 756 - 4688 E-mail: inf o@ariens.
An important point after buying a device Ariens 921032 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ariens 921032 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ariens 921032 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ariens 921032 you will learn all the available features of the product, as well as information on its operation. The information that you get Ariens 921032 will certainly help you make a decision on the purchase.
If you already are a holder of Ariens 921032, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ariens 921032.
However, one of the most important roles played by the user manual is to help in solving problems with Ariens 921032. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ariens 921032 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
