Instruction/ maintenance manual of the product GP30 Miller Electric
Go to page of 19
1242 ARIZONA AVE. LARCHWOOD, IA 51241 1-800-570-82 05 GP30 LO ADER P ARTS and INSTRUCTIONS O WNER’S MANU AL.
TO PREVENT POSSIBLE ROLLOVER, OBSERV E T HE FOLLOWING SAFETY PR ECAUTIONS ♦ Carry loads as low as poss ible ♦ Drive tractor slowly when turning, operating on hills or inclines, or traversing un- e.
T ABLE OF CONTENTS • Composite Bearing Information • Mounting Loader on T ractor • Dismounting Loader • Quick-attach Instructions • Parts Schematics • Cylinder Packing Detail • Loader S pecifications • W arranty SERIAL No.
COMPOSITE BEARING INFORMA TION FIGURE A . Your GP/GL-Series loader is equipp ed with composite, greaseless bearings at all (12) pivot points. These high-quality bearings should not be confused with plastic bushings, sintered bushin gs, or meta l-backed bearings.
MOUNTING LOADER STEP 1 For a new loader installation, the mountings must be installed on th e tractor first. Refer to the typical mounting kit shown in Figure 1. A detailed schematic of your specific kit is available—just call 1-800-570-8205 if the schematic was not included with yo ur new loader.
DISMOUNTING LOADER STEP 1 DRIVE THE TRACTOR ON TO FLAT CONCRETE and place the loader in the position shown in Fig 1. STEP 2 Remove the stand legs fro m their stored position and place them in their dismount positio n. Slide th e in- ner tubes down to the extended position and secu re them with the 3/4” pins.
QUICK-A TT A CH INSTRUCTIONS UNCOUPLING 1. Raise sliding latches as show n in Figure 1. 2. Rotate QT pins out of the lower notches, ra ise, an d then rotate them into the upper notche s of the sliding latc hes as shown in Figure 2. 3. Slide the sliding latches do w n as shown in Fi gure 3.
1 8 15 19 29 10 15 19 16 14 17 30 36 27 28 13 12 35 3 26 18 2 11 9 31 32 29 34 33 29 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 MF30 MAINFRAME, GL30/GP30 1 2 QT30 QUICK ATTACH FRAME 1 3C Y - 0 5 9 CYLIND.
ITEM NO. PART NUMBER DESCRIPTION with bearings/QTY. 20 BR-2500K-3750 COMPOSITE BEARING, 2.00 BORE, 3.75 LONG 2 21 PS-2000-45 Pin Seal (MRW), 2.0 ID x 2.5 OD x 5/16 Thick 8 22 BR-2000K-1500 COMPOSITE BEARING, 1.50 BORE, 1.50 LONG 2 23 BR-2500K-3125 COMPOSITE BEARING, 2.
ITEM NO. PART NUMBER DESCRIPTION Pin Up Latch Up/QTY. 1 QT02-01L SLIDING LATCH ASSY, QT, LH 1 2 QT02-01R SLIDING LATCH ASSY, QT, RH 1 3 QT02-14 RETAINING PIN ASSEMBLY, QT 2 4 QT30-W WELDED QT FRAME 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 4 HW-NS-06-A NUT, 3/8-16 UNC, CL, ZN 4 5 HW-SP-01 SPRING, QT HANDLE 4 6 HW-WS-06-A WASHER, 3/8, FLAT, ZN 4 DWG.
DWG. NO. SHEET REV. DATE GL30/GP30 HOSES & PIPING OF 1 A 1/1 3/2005 HP30 1 SCHE MATIC WEIGHT: 23.706 ITEM NO. PART NUMBER DESCRIPTION with pipes/QTY.
ITEM NO. PART NUMBER DESCRIPTION with aux kit/QTY. 24 HP30P-GU AUXILLARY FEEDLINE, UPPER 1 25 HP30P-GL AUXILLARY FEEDLINE, LOWER 1 26 SF-2706-LN-10-08 BULKHEAD CONNECTOR, -10 JIC to 1/2 NPT 2 27 PC06X.
3 2 1 7 8 6 7 5 4 9 7 8 7 6 ITEM NO. PART NUMBER DESCRIPTION Stand Legs/QTY. 1 SL30-TL TOP TUBE ASSY, LEFT 1 2 SL30-BL BOTTOM TUBE ASSY, STAND LEG (LH) 1 3 SL30-HL STAND LEG HANDLE, LEFT 1 4 SL30-TR T.
ITEM NO. PART NUMBER DESCRIPTION QTY. 1 CY-059T TUBE ASSEMBLY, GP/GL25-30 BUCKET 1 2 CY-059D ROD ASSY, GL/GP30 BUCKET 1 3 CP-GL-3017-S GLAND, 3017, SHORT-TAIL 1 4 CP-PS-3017-U PISTON, 3017 U-CUP 1 5 HW-NS-16-A NUT, 1-14 UNF, TOP LOCK, PLAI N 1 6 CP-KT-3017-U P-KIT, 3.
3 4 2 5 1 7 NOTES: 1 . BEAR ING AND SEALS SOLD SE PARATELY. 2. PACKING KIT SHOWN IN PART LIST, BUT NOT SHOWN IN DRAWING. 3. EAR LY CYLIN DER S (1 2/04-2/05) WERE 1 " SHOR TER AN D HAD 1 " LESS STROKE . SEE NOTE 1 8 8 DWG. NO. SHEET DATE LIFT CYLINDER, GP30, LH OF 1 1/ 28/2005 CY -060 -L 1 SCH EMATI C ALL DIMENSIONS IN INC HES 85.
ITEM NO. PART NUMBER DESCRIPTION QTY. 1 CY-058D ROD ASSEMBLY, GL/GP30 LIFT 1 2 HW-NS-16-A NUT, 1-14 UNF, TOP LOCK, PLAIN 1 3 CY-060-RT TUBE ASSEMBLY, GP30 LIFT, RH 1 4 CP-GL-3520-L GLAND, 3520 LONG-TAIL 1 5 CP-PS-3520-U PISTON, 3520 U-CUP 1 6 CP-KT-3520-U P-KIT, 3.
ROD WIPER PISTON GLA ND SEA L, U-CUP, LARGE SEAL, U-CU P, SM ALL O-RING, SMA LL O-RING, LARGE B/U WA SHER SNAP RI NG SCHE MATIC DWG. NO. SHEET REV. DATE PACKING CONFIGURAT ION, U-CUP OF 1 A 1/1 3/2005.
14’−8" 13’−6" 2’−11" 34° 44° 11’−10" 8" 100" TYPICAL GP30 SPECIFICA TIONS SPECIFICATIONS AND PERFORMANCE NUM BERS ARE FOR REFERENCE ONLY WEIGHT S: Loader (less bucket and mounts) : 2090 lbs. 8 FT Bucket : 800 lbs.
WARRANTY Dec 2004 ALL PRODUCTS MANUFACTURED BY MI LLER LOADERS, INCOPRORATED ( MLI ) EXCEPT THE CHROME-PLATED PIVOT PINS USED ON GR EASELESS LOADERS, ARE GUARENTEED TO THE ORIGINAL PURCHASER FOR A PER.
An important point after buying a device Miller Electric GP30 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miller Electric GP30 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miller Electric GP30 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miller Electric GP30 you will learn all the available features of the product, as well as information on its operation. The information that you get Miller Electric GP30 will certainly help you make a decision on the purchase.
If you already are a holder of Miller Electric GP30, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miller Electric GP30.
However, one of the most important roles played by the user manual is to help in solving problems with Miller Electric GP30. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miller Electric GP30 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
