Instruction/ maintenance manual of the product T 9820 Miele
Go to page of 36
Operating Instructions for the T 9820 Gas Dryer To prevent accidents and machine damage read these instructions before installation or use. M.-Nr. 07 268 170 en - US, CA.
2.
3 , W ARNING For y our safety the inf ormation in this manual must be f ollo wed to minimize the risk of fire or explosion or to pre vent pr operty damage , personal injury or death. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 First use . . . . . . . . . . .
, WARNING - To reduce the risk of fire, electric shock or injury to persons when using your appliance follow basic precautions, including the following: The T9820 gas dryer is only approved for use in the USA and Canada. It is not approved for use in Mexico.
~ Allow the dryer to complete each stage of the program selected, including the cooling down phase. This will ensure that the items being removed are not too hot to handle. ~ Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in these Operating instructions.
~ Product failure due to improper installation is not covered under the Warranty. ~ Gas dryers are not approved for mobile home installation. ~ Check regularly on the exhaust parts (e.g. wall vent duct, louvered wall vent, bends, etc.) if enough air gets through.
a Program buttons To select a drying program b Options buttons Special features to enhance a drying program c Check Filter/Vent indicator Indicates to clean the filter or vent d Status indicator Shows the current cycle of the drying program e Start/Stop button Starts and stops a program, or if pressed and held in cancels a program.
Metal components of the dryer's gas burner have a protective coating which may give off a slight odor the first time the appliance is turned on. The smell will dissipate after a short time and does not indicate a faulty connection or appliance defect.
Clean the drum interior before the first use. Fabric care labels Before drying, check fabric care labels for special drying instructions. q = Drying with a normal temperature r = Drying with a low temperature s = Do not dry in a tumble dryer Drying tips – Observe the maximum loads, see the "Program Guide".
1. Sort the laundry ^ Sort the laundry by desired dryness, fabric, size and similar residual moisture after spinning to assure even drying results. , Do not dry items that may melt or ignite in the dryer such as plastics or rubber. They could melt and damage the laundry.
2.2. With laundry basket Reduce the load size to ½ of a normal load. Use the laundry basket to dry or air e.g. sport shoes. The laundry basket is designed in such a way that it does not turn with the drum and avoids strain on the drying item. ^ Hang the laundry basket in the opening.
2.3. Close the door , To prevent fabric damage, check that laundry will not be caught in the closed door. The lint filter must always be inserted in the door opening. ^ Close the door with a firm swing and push it closed. 3. Select a program ^ Press the button of the desired program.
4. Select an option ^ Press any button. The combination "Turbo/Gentle" is not possible. Turbo Heat resistant items (with fabric care symbol q ) will be dried at a high temperature. – Laundry will be dried faster. Gentle Items sensitive to high temperatures (with fabric care symbol r ) will be dried at a low temperature.
5. Start the program During the program selection the "Start/Stop" indicator flashes meaning that the program can be started. ^ Press the "Start/Stop" button. The "Start/Stop" indicator lights. The "Status" indicator of the reached drying degree lights.
6. Program end - Unload the laundry The "Anti-crease/End" indicator will light at the end of the program and the buzzer will sound if it was selected.
Quick Guide Remove this guide for easy reference To prevent accidents and machine damage read these instructions before installation or use..
1. Prepare and sort the laundry ^ Check for damages and foreign objects. ^ Close zippers, hooks and eyelets. ^ Tie up belts and apron ties. 2. Load the laundry ^ Open the door. Without the laundry basket ^ Load the laundry loosely in the drum. , To prevent fabric damage, check that laundry will not be caught in the closed door.
3. Select a program ^ Press the desired program button. 4. Select an option ^ Select an option button, if desired. The combination "Turbo/Gentle" is not possible. 5. Starting a program ^ Press the "Start/Stop" button. 6. Program end - Unload the laundry The Anti-crease/End indicator lights.
Short program guide Extra Dry Multi-layer, mixed loads of sturdy cottons, e.g. towels, bath robes. The "Extra dry" program should not be selected for jersey materials. Items may shrink. Options: Turbo or Gentle, Buzzer Normal Single and multilayered cotton and linen laundry e.
Extra Dry Items Multi-layered, mixed loads of sturdy cottons, e.g. towels, bath robes. Note The "Extra dry" program should not be selected for jersey materials. Items may shrink. Options Turbo or Gentle, Buzzer Normal Items Single and multilayered cotton and linen laundry e.
Woolens Items Woolen fabrics Note – Reduce the load size to 1/3 of a normal load. – Woolen items will be fluffed for a short time, but not completely dried.
, Repairs to electrical and gas appliances must only be carried out by a qualified and trained person in accordance with local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work.
The laundry is not dry enough. Possible fault Solution The load contained too many dissimilar items (size and fabrics.) – Continue drying using the "Warm air" program. – Select a suitable program. The laundry is still wet. The program runs too long.
Fault indicators The "Check Filter/Vent" indicator lights. Possible fault Solution The dryer does not work at its optimum or not efficiently. The lint filter might be clogged with lint or detergent residues. – Usually cleaning the lint filter fixes the problem.
The program is canceled. The Anti-crease/End indicator lights. The buzzer sounds. Possible fault Solution This is not a fault. The electronic has detected that there is no laundry in the drum and cancels the program. Single items or already dried laundry can also cause a program stop.
Repairs In the event of a fault which you cannot fix yourself, please contact the service number on the back of this manual. When contacting Technical Service, please quote the model and serial number of your appliance. These can be found on the data plate.
24.
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use..
Cleaning the lint filter The lint is collected by the lint filter in the door opening. The lint filter must be cleaned after every program. ^ Clean the lint filter whenever the "Check Filter/Vent" indicator comes on. ^ Pull out the lint filter.
Cleaning the exterior and the control panel , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the dryer.
Changing the light bulb To reduce the risk of electric shock, disconnect the appliance from the power supply by unplugging or tripping the circuit breaker. ^ Open the door. The lighting is in the drum opening in the upper right-hand corner. ^ Remove the screw.
Disposal of the packing materials The packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. To prevent suffocation, ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
30.
31.
All rights reserved / 2108 For the most updated manual please see the Miele web site. M.-Nr. 07 268 170 / 01.
An important point after buying a device Miele T 9820 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele T 9820 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele T 9820 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele T 9820 you will learn all the available features of the product, as well as information on its operation. The information that you get Miele T 9820 will certainly help you make a decision on the purchase.
If you already are a holder of Miele T 9820, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele T 9820.
However, one of the most important roles played by the user manual is to help in solving problems with Miele T 9820. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele T 9820 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
