Instruction/ maintenance manual of the product T 4222 C Miele
Go to page of 44
Operating instructions f or condenser tumb le dr y er T 4222 C T o avoid the risk of accidents or damage to the machine it is essential to read these operating instructions before it is installed or used for the first time.
W arning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Caring for the en vironment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Disposal of the packing material .
Prob lem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Check and fault indicator lamps .
T o avoid the risk of accidents and damage to the machine please read these instructions carefully befor e using it for the first time. They contain important infor mation on its safety , use and maintenance. Keep these operating instructions in a safe place and ensure that new users are familiar with the content.
If the connection cable is faulty it must only be replaced by a Miele approved service technician to pr otect the user from danger . In the event of a fault or for cleaning purposes, the machine is on.
Always close the door after use. This way you will avoid the danger of: – children climbing onto or into the dryer or hiding things in it. – pets or other small animals climbing into it. Do not let anyone sit or lean on the door , as this can cause the machine to tip up.
Disposal of the packing material The transport and protective packing has been selected from materials which are envir onmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
a Programme selector The programme selector can be turned clockwise or anti-clockwise. b Programme sequence and c heck lamps c Start button Press the Start button to start a programme. The Start indicator lamp will flash as soon as a programme can be started.
W ash care labels Before drying check the drying symbol on the wash care label. Significance of symbols: q Dry at nor mal temperature r Dry at low temperature s Do not tumble dry If no symbol is featu.
Programmes Fabric type Special notes CO TTONS Drying levels maximum load: 5 kg (1) Normal+ Single and multi-layered fabrics, e.g. mixed load of cotton fabrics (e.g. towelling, jerseywear). - Normal (2) Load of similar cotton fabrics (jersey wear , flannelette sheets, towelling).
Programmes Fabric type Special notes MINIMUM IRON Drying levels maximum load: 2.5 kg (1) Normal+ Minimum iron items which are made of synthetic or blended fabrics (e.g. pullovers, dresses, tr ousers) which are not dried adequately in the Normal programme.
Programme Fabric type Special notes Special care programmes W oollens hand care maximum load: 2 kg (1) Woollen fabrics T o refr esh and fluff up woollen garments quickly . Remove garments immediately at the end of the programme. Do not r epeat. Woollen fabrics ar e not dried completely by this programme.
A Prepare the laundry ^ As far as possible, sort laundr y for: - the type of fibre or weave, - the degree of dryness requir ed, - similar size of items, - the moisture content after spinning. This will help towards achieving an even drying result. Fasten duvet covers etc.
C Select a programme ^ T ur n the programme selector to the requir ed programme. See "Consumption data" chart for programme durations. Low temperature ^ For drying par ticularly delicate fabrics (care symbol r ) e.g. acrylics turn the programme selector to the Low temperature position.
Selecting a different pr ogramme As long as the cooling down phase or the anti-crease phase has not been reached it is possible to change a programme after it has started by turning the programme selector to a differ ent programme position. Interrupting a programme ^ Switch the machine off with the I-On/0-Off button.
Emptying the condensed water container The condensed water will be collected in the condensed water container unless the machine has been fitted with a drain hose (see installation). The condensed water container should be emptied after every drying cycle or as soon as the Empty out container indicator lamp comes on.
Cleaning the fluff filters The fluff which is cr eated by the drying process is collected by the fluf f filters in the door and the door opening. Clean the filters after each drying programme. Cleaning them whilst dry ^ Open the door and pull the fluff filter out of the door as illustrated.
Cleaning them with water If there is a gr eat deal of compacted fluff on any of the filters, they can be removed and cleaned under hot running water . ^ T o remove the fluf f filter from the door holder see previous page. ^ T o remove the filters in the door opening, grip the holder and push upwards in the dir ection of the arrow to remove it.
Cleaning the condenser unit Detergent residue, hair and fine fluf f from the dryer can get through the fluf f filters and block the condenser unit. Dust from the r oom in which the dryer is installed can also get into the condenser unit and cause a blockage.
^ Pull the condenser unit out of its housing by the handle. Checking the condenser unit ^ Hold the condenser unit up to the light as shown . ^ Check to see if there is any fluf f inside it. The arrows in the illustration above indicate where to look. If you cannot see any fluff: ^ Replace the condenser unit (see following page).
^ Then flush the unit through fr om the front. ^ Check the condenser unit again for any visible fluff and if necessary flush it through again until it has all gone. ^ Remove any soiling still visible inside the housing unit. ^ Also make sure the rubber seals ar e clean.
With the help of the following notes minor faults in the perfor mance of the machine, some of which may result fr om incorrect operation, can be put right without contacting the Service Department.
Prob lem P ossible cause Remedy There is a build up of fluff. Fluff is principally the r esult of friction when garments are being worn and washed. Machine drying hardly causes any fluf f to form and has been established by resear ch institutes to have no effect on the lifetime of fabric.
Prob lem P ossible cause Remedy The drying process goes on too long or even s witches off . Important : Before attempting to remedy one of the following causes, switch the dryer off and switch on again to start the programme again. V entilation to and from the dryer may be insufficient (e.
Prob lem P ossible cause Remedy The condenser unit service panel will not shut. The inner cover of the condenser unit has not been locked properly and/or the condenser unit has not been positioned correctly . – Ensure that the condenser unit is positioned correctly and lock the cover .
Prob lem P ossible cause Remedy The programme has stopped, the Anti- crease/Finish lamp has come on in the sequence display and the buzzer is sounding. This is not a fault. The electronic unit has recognised that ther e is no laundry in the drum and cancelled the programme.
T o change the interior drum lamp ^ Open the door . Before changing the lamp, disconnect the machine from the mains power supply . Y ou will find the interior lamp cover at the top of the drum aperture. ^ Insert the opener under the side edge of the cover as illustrated.
After sales service Repairs In the event of any faults which you cannot remedy yourself, please contact – your Miele Dealer or – The Miele Service Department (see back cover for address).
Front vie w a Mains connection cable b Condensed water container c Control panel d Door e Service panel for condenser unit f Four height-adjustable screw feet g External drainage options (e.
Installation site , Make sure the dryer door can be opened without hindrance after installation. T ransporting the machine to its installation site When moving the machine you can hold it by the lid where it pr otrudes to the rear of the dryer .
Aligning the machine The machine must be perfectly level to ensure safe and pr oper operation. ^ The screw feet can be adjusted to compensate for any unevenness in the floor . , The ventilation gaps in the plinth must not be covered over as this would prevent a suf ficient intake of air .
External condensed water outlet When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer . The condensed water can also be drained off dir ectly if the machine is installed near a sink, drain outlet etc.
Connection to a sink drain outlet The drain hose can be connected directly to a sink drain outlet. ^ Remove the following from the back of the dryer at the bottom: Adapter 1 and hose clip 3 behind it. ^ Fit adapter 1 to the sink drain outlet using nut 2 .
Electrical connection U .K. All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the appliance until after installation work has been carried out.
Programme Capacity Final spin speed (in a domestic washing machine) Electricity consump- tion Drying time incl. cooling down time kg rpm kWh Minutes CO TT ONS Normal + 5.0 1200 1400 1600 1800 2.80 2.65 2.40 2.35 77 74 67 66 Normal (1) 5.0 800 (70 % residual moisture) 3.
Height 85 cm (adjustable +0.7/- 0.7 cm) Height without lid 82 cm Width 59.5 cm Depth 58 cm Depth with door open 106 cm Weight 54 kg Drum volume 100 litres Maximum capacity 5 kg dry weight Capacity of condensed water container approx. 3.5 litr es Length of connection cable 1.
Progr ammable functions f or changing standard settings 37.
Increased drying level in the CO TT ONS programmes The machine is designed to dry using as little energy as possible. However , if you require the laundry to be drier , it is possible to reduce the final moisture level in the COTTONS programmes. Note that pr ogramme durations will be longer if this option is activated.
Increased drying level in the MINIMUM IRON pr ogrammes The machine is designed to dry using as little energy as possible. However , if you require the laundry to be drier , it is possible to reduce the final moisture level in the MINIMUM IRON programmes.
Buzzer An audible tone sounds repeatedly at the end of a programme. The buzzer is activated as standard ex- works. It can be deactivated if wished. The buzzer will sound if there is a fault, even if it has been deactivated. Follow steps A to G to programme and store in memory .
41.
42.
43.
M.-Nr . 06 067 730 / 01 e n-G B Alteration rights reserved/3804.
An important point after buying a device Miele T 4222 C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele T 4222 C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele T 4222 C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele T 4222 C you will learn all the available features of the product, as well as information on its operation. The information that you get Miele T 4222 C will certainly help you make a decision on the purchase.
If you already are a holder of Miele T 4222 C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele T 4222 C.
However, one of the most important roles played by the user manual is to help in solving problems with Miele T 4222 C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele T 4222 C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
