Instruction/ maintenance manual of the product 920006 Ariens
Go to page of 34
Owner/Operator Manual Manuel Du Prop riétaire/Utilisa teur Models 920006 – Compact 24 920007 – Compact 20 920010 – Compact 24 Sno-Thro ® 03882500B 9/09 Printed in USA ENGLI SH FRANÇAIS.
GB - 2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 4 ASS EM BL Y . . . . . . . . . . . . . . . . . . . . . . . 8 CONTROLS and FEA TURES . . . . . . . . .1 1 OPERA TION . . . . . . . . . . . . . . . . . . . . . 12 MAINTENANCE . . . . . . .
GB - 3 • Record Unit M odel and Serial numbers here. • Record Engine Model and Serial numbers here. PRODUCT REGISTRATION The Ariens d ealer must register the product at the time of purchas e. Registering the product will help the company process warranty claims or contact you with the latest service information.
GB - 4 SAFETY ALERT S Look for these symbols to point out important safety precautions. They mean: Attention! Personal Safe ty Is Involved! Become Alert! Obey The Message! The safety alert symbols above an d signal words below are used on decals and in this manual.
GB - 5 1. W ARNING! 2. DANGER! 3. DANGER! SAFETY RULES Read, understand, and follow al l safety practices in Owner/Operator Manual before beginning assembly or operating. Failure to follow instructions could result in personal injury and/or d amage to unit.
GB - 6 DO NOT operate near drop-offs, di tches, or embankments. Unit can s uddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. Falling snow , fog, etc. can reduce vision and cause an accident . Operate unit only when there is good visibility and light.
GB - 7 Never leave a running unit unattended. AL WA YS shut off engine before l eaving unit. AL WA YS remove key to prevent unauthorized use. Never carry passengers. Check clutch and brake operation frequently . Adjust and service as required. All motion of drive wheels and auger/impeller must stop quickly when cont rol levers are released.
GB - 8 PACKAGE CONTENTS ASSEMBLY T ools Required : • Pliers • Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustabl e Wrench •T i r e G a u g e Unfold Handleba r (Figure 4) 1. Remove the lower and loosen the upper hardware on the handlebar assembly .
GB - 9 Inst all Discharge Chu te (Figure 5) 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardware from the bottom of the chute pedestal. 3. Install discharge chute over opening in the auger housing and secure pedestal to auger ho using with hardware removed in step 2.
GB - 10 Check T ire Press ure Check tire pressure and adjust to the pressure listed on tire sidewall. Check Auger Gear case Oil Check oil level in auger gearcase (see Check Auger Gearc ase on page 19). Check Engine Crankca se Oil IMPORT ANT : The engine is shipped with 5W-30 oil in crankcase.
GB - 11 1. Attachment Clutch Le ver 2. Speed Selector 3. Traction Drive Clutch Lever 4. Chute Crank 5. Muffler Guard 6. Discharge Chute Deflector 7. Discharge Chute 8. Impeller 9. Auger 10. Scraper Blade 1 1. Auger G earcas e 12. Clean-out T ool 13. Oil Fill and Dipstick 14.
GB - 12 CONTROLS AND FEA TURES See Figure 7 for all Controls and Features locations. Dual Handle Interlock When Attachment Clutch and th en T raction Drive Clutch are engaged, the Attachment Clutch will remain engaged (leve r down) if released. T o stop attachment, release T raction Drive Clutch and both clutches will disengage.
GB - 13 S peed Selector Position the Speed Selector in the appropriate speed notch to control forward and reverse t ravel. Forward: (6) Fastest (1) Slowest Reverse: (1) Slow (2) Fast IMPORT ANT : DO NOT change motion from forward to revers e with clutch engaged.
GB - 14 Recoil St arter Handle When pulled, handle will turn engine over . IMPORT ANT : DO NOT let handle snap back against starter . See St arting and S hut Off on page 1 6. Snow Clean-Out T ool (Figure 9) T o clear the discharg e chute: 1. Shut off the engine.
GB - 15 Scraper Blade The scraper blade allows the back of t he housing to keep better contact wit h the surface being c leared. It also prevents damage to the hous ing from normal use . IMPORT ANT : DO NOT allow Scraper Blade to wear too far or Auger/Impeller housing will become damaged.
GB - 16 5. Fill fuel t ank to within 1/2 in. (1.2 cm) below bottom of filler neck with unleaded gasoline. 6. Replace Fuel Cap and tighten. 7. AL WA YS clean up any spilled fuel. PRE- ST A RT 1. Frozen Impeller IMPORT ANT : Before starting engine, check impeller to be s ure it is not frozen.
GB - 17 9. Repeat steps 7 and 8 until engine start s. (If engine does not start, ref er to TROUBLESHOOTING on page 30.) 10. Adjust choke as need ed. 1 1. Set thr ottle to P art T hrot tle or Slow position for adaptation to out s ide temperature or travel.
GB - 18 Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency . Should engine service be required, contact an Ariens dealer or an auth orized engine manufacturer's service center .
GB - 19 CHECK CLUTCH OPERATION Auger / impe ller must stop within 5 seconds when attachment clutch/impeller brake lever is released. Wheels must st op quickly when traction drive clutch lever is released.
GB - 20 SCRAPER BLADE IMPORT ANT : Damage to auger/impeller housing will result if blade wears down too far. Scraper blade is adjustable to compensate for wear . T o adjust sc raper blade: 1. Tip unit back onto handlebar , support housing and loosen nuts retaining blade 2.
GB - 21 SHEAR BOLTS IMPORT ANT : Use only Ariens shear bolts for replacement. Use of any other type of s hear bolt may result in severe damage to unit and may void the warranty . Occasionally a foreign object may enter the auger/impeller housing and jam the auger , breaking shear bolts which secure the auger to the shaft (Figure 15).
GB - 22 SP EED SELECT OR ADJUSTMENT T o adjust (Figure 1 8): 1. Disconnect adjustment pivot pin from speed select or arm. Save ha rdware for reinstallati on. 2. Place the speed selector on dash panel in the fastest forward speed position. 3. Turn the speed selector arm straight down towards the ground as far as it will go.
GB - 23 7. Remove hex bolts securing housing to frame (two on each side). Tip housing and frame apart on pivot pin. 8. Remove attachment drive belt from attachment pulley (hold brak e away from belt). Replac e Atta chment Driv e Belt 1. Place new belt onto attachment pulley .
GB - 24 T RACTION DRIVE BELT REPLACEMENT NOTE: Housing and frame must be tipped apart and attachment drive belt removed from engine sheave in order to change traction drive belt (Figures 19, 20, 21 and 24) 1. Remove attachment drive belt (S ee Remove Attachment Drive Belt on page 22).
GB - 25 2. Loosen jam nut on cable adjustment barrel, and then turn the adjustment barrel down to shorten cable and remove all c able slack. See F igure 24. 3. With the at tachment clutch disengaged, check that the attachment idler arm lightly touches the frame.
GB - 26 Adjust th e Atta chment Clutch Cable S pring Extension 1. Check the attachment clutch cable spring extension. Measure the length o f the attachment clutch cable spring with the clutch lever disengaged. Then measure the attachment clutch spring with the clutch lever engaged.
GB - 27 Check Belt Finge r Clear a nce (Figure 29) 1. With c lutch lever engaged, the belt finger located opposit e the belt idler must be less than 1/8 in. (3,2 mm ) from belt, but not touching the belt . T o adjust belt finger , loosen the bolt s and move the finger to the proper position.
GB - 28 FRICTIO N DISC R EPLAC EMENT Remove Friction Disc (Figu re 31 and Figure 32): 1. Shut off engine, remove key , disconn ect spark plug wire and allow unit to cool completely . 2. Place the unit into the service position on a level surface. 3. Remove lockpins from wheel axles and remove wheels.
GB - 29 SHORT T E RM IMPORT ANT : NEVER spray unit with high pressure wa ter or store unit outdoors . Run with attachment clutch engag ed a few minutes after each use to free unit of any loose or melting snow . Close fuel shut-off valve. Inspect unit for v isible signs of wear , breakage or damag e.
GB - 30 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine wi ll not crank/ start. 1. Fuel tank is empty . 2. Fuel shut-off valve closed. 3. Build up of dirt and residue around governor/carburetor . 4. Key Switch not in run position. 5. Electric starter not functioning.
GB - 31 SPECIFICA TIONS Model Nu mber 920006 920007 920010 Description Compact 24 Compact 20 Compact 24 Engin e Briggs & S tratton 900 Series Briggs & Stratton 900 Series Subaru SX17 Gross T orque* - ft-lbs (N-m) 9.0 (12.2) 9.0 (12.2) TBD Displacement - in.
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® MOWE R | BYNORM ® | EVERRIDE ® | GREA T DANE ® Snow_200 8 32 Three-Y ear Limi ted Sno-Thro ® Wa r r a n t y Ariens Company (Ariens.
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NAT IONAL ® | BYNORM ® | EVE RRIDE ® | GREA T DANE ® Snow_2008 33 Limitations • Batteries are war ranted only f or a period of 12 month s after dat e of purcha se, on a pro rated basis. For the first 90 da ys of the warra nty period, a defe ctive battery will be re placed free of charge.
Ariens Company 655 West Ryan St reet Brillion, W I 541 10-1 072 920-756-2141 www .ariens.com.
An important point after buying a device Ariens 920006 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ariens 920006 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ariens 920006 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ariens 920006 you will learn all the available features of the product, as well as information on its operation. The information that you get Ariens 920006 will certainly help you make a decision on the purchase.
If you already are a holder of Ariens 920006, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ariens 920006.
However, one of the most important roles played by the user manual is to help in solving problems with Ariens 920006. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ariens 920006 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
