Instruction/ maintenance manual of the product M.-Nr. 09 416 500 Miele
Go to page of 76
Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time.
Description of the appliance .........................................5 Appliance overview .................................................5 Control panel ......................................................6 Warning and Safety instructions .......
Operation .......................................................3 5 Detergent ........................................................3 5 Adding detergent ..................................................3 6 Switching on ............................
Maintenance .....................................................6 2 Cleaning the water inlet filter .........................................6 2 Cleaning the drain pump and non-return valve ...........................6 3 Programme chart .............
Appliance overview a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Filter combinat.
Control panel a Check/Refill indicators b Time display c Delay start button , with indicator light d Turbo button with indicator light e Programmes f Programme selector button g On/Off button K with i.
This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time.
Safety with children ~ Children under 8 years of age must be kept away from the appliance unless they are constantly supervised. ~ Children 8 years and older may only use the dishwasher if they have been shown how to use it in a safe way and understand the hazards involved.
Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Under no circumstances should you use a damaged appliance. It could be dangerous. ~ The dishwasher must only be plugged into the electricity supply via a suitable switched socket.
~ Before connecting the appliance, check that the connection data on the data plate (voltage and frequency) match the mains electricity supply. If in any doubt, consult a qualified electrician. ~ The electrical safety of this appliance can only be guaranteed if correctly earthed.
~ The plastic housing of the water connection contains an electrical component. The housing must not be dipped in water. ~ There are electrical wires in the water inlet hose.
~ Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician, otherwise any subsequent damage will not be covered by the guarantee.
Correct installation ~ The dishwasher must be installed and connected in compliance with the diagram supplied. ~ Take care, both before and during installation of the dishwasher, not to cut yourself on the metal parts. Danger of injury. Wear protective gloves.
Correct use ~ Do not use solvents in the dishwasher. Danger of explosion. ~ Do not inhale or ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing.
~ Do not fill the rinse aid reservoir with powder or liquid detergent. This will cause serious damage to the reservoir. ~ Do not fill the salt reservoir with powder or liquid dishwasher detergent.
Accessories ~ Only use genuine Miele original spare parts and accessories with this dishwasher. Using spare parts or accessories from other manufacturers will invalidate the guarantee, and Miele cannot accept liability. Disposal of your old dishwasher ~ Make the door lock inoperative so that children cannot accidentally shut themselves in.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Energy saving dishwashing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your water supply is suitable, this dishwasher can be connected to a hot water supply for further economies.
To open the door ^ Pull the handle. If the door is opened during operation all functions are automatically interrupted. To close the door ^ Push the baskets right in.
Water softener In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in the build-up of calcium deposits on crockery and in the dishwasher. Mains water with a hardness level higher than 0.7 mmol/l (4° d – German scale) needs to be softened.
Programming the water hardness level ^ Switch the dishwasher off with the On/Off button K , if it is switched on. ^ Press and hold the programme selector button X . ^ Switch the dishwasher on using the On/Off button K , and hold the programme selector button X in until the lower right hand programme indicator lights up.
Before using the appliance for the first time, you require: – approx. 2 litres of water, – approx. 2 kg dishwasher salt*, – domestic dishwasher detergent*, – rinse aid* formulated for domestic dishwashers. Every dishwasher is tested at the factory.
^ Remove the lower basket and unscrew the salt reservoir cap. Water or saline solution will run out of the reservoir when the cap is removed. It should therefore only be removed in order to refill the salt reservoir. ^ Fill the reservoir with approx. 2 litres of water (first use only).
Switching off the refill indicators If you only ever use combination products containing salt and rinse aid in your dishwasher, you can disable both of these indicators if you wish.
Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically.
^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid reservoir during a programme. ^ Wipe up any spilled rinse aid.
Setting the rinse aid dosage The rinse aid dosage can be set from approx. 0-6 ml. It is set to a recommended setting of approx. 3 ml at the factory. If the Adust Sensor wash function has been activated, the amount of rinse aid dispensed in the Sensor wash programme can be higher than that set.
Note Remove coarse food residues from crockery. There is no need to rinse items under running water. , Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher.
Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher.
Upper basket , For safety reasons, do not operate the dishwasher without the upper and lower baskets in place. ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc. Shallow pans or casserole dishes can also be placed in the upper basket.
Adjusting the upper basket In order to gain more space for taller pieces of crockery in the lower or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low.
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Glasses, cups and small items such as saucers can also be placed in the lower basket.
Cutlery Cutlery tray (depending on model) ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Cutlery basket (depending on model) The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier.
Detergent , Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Active ingredients Modern detergents contain various active ingredients, the most important of which are: – Phosphates to prevent calcification. – Alkalis to aid removal of dried on soiling.
Failure to dispense the recommended amount of detergent may impair cleaning results. , Avoid inhalation of powder detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing.
For information Compartment I holds max. 10 ml, Compartment II holds max. 50 ml. There are markings in compartment II to assist with dispensing: 20, 30.
Switching on ^ Open the stopcock, if it is closed. ^ Open the door. ^ Make sure the spray arms are not obstructed. ^ Switch the dishwasher on with the On/Off button K . The On/Off indicator light K and one of the programme indicator lights will come on.
Time display The duration of the programme selected appears in hours and minutes in the display before the programme begins. During the programme, the time left until the end of the programme is displayed. The time displayed may vary with the same programme.
At the end of the programme ^ Open the door slightly to check that the programme has finished. 0 appears in the time display when the programme has finished. If the programme indicator light is still flashing, the programme has not yet finished. Close the door again to allow the programme to finish.
Interrupting a programme A programme is interrupted as soon as the door is opened. If the door is closed again, the programme will continue after a few seconds from the point it was at before the door was opened. , Water in the dishwasher may be hot. Danger of scalding.
Turbo The Turbo function is used to reduce the duration of programmes in which this function is available. In order to achieve optimum cleaning results, consumption rates are increased when Turbo has been selected. ^ Open the door. ^ Switch the dishwasher on with the On/Off button K .
^ Open the door. ^ Switch the dishwasher on using the On/Off button K . The On/Off indicator light K will come on. ^ Select the programme required with the programme selector button. ^ Press the , button. The last Delay start time used will appear in the display.
Buzzer A buzzer sounds at the end of the programme or if there is a fault. You will hear the buzzer at the end of a programme. It will sound four times in intervals with a noticeable pause in between. In the event of a fault, the buzzer will sound four times in intervals with only a very short pause in between.
Adjust Sensor wash You can adjust the Sensor wash programme so that it will remove stubborn soiling in a lightly soiled load. ^ Open the door. ^ Switch the dishwasher off using the On/Off button K . ^ Press the programme selector button X in, and whilst holding it in switch the dishwasher on using the On/Off button K .
Memory You can use the Memory function to save the last programme selected. Instead of the ECO programme, the last programme selected will appear in the display when the dishwasher is switched off and back on again at the end of a programme. ^ Open the door.
Optimise standby To save energy, the dishwasher will switch to Standby mode a few minutes after the last time a button has been pressed or a few minutes after the end of the programme. The indicator lights and the time display will go out and only the On/Off indictator light K will flash slowly.
Factory default If you have altered any settings from the factory default, you can re-set them back to the factory default settings as follows: ^ Open the door. ^ Switch the dishwasher off using the On/Off button K . ^ Press the programme selector button X in, and whilst holding it in switch the dishwasher on using the On/Off button K .
Check your dishwasher regularly (approx. ever y4-6 months). This way faults and problems can be avoided. , The external surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the external surfaces.
Cleaning the control panel and door front , Remove any soiling immediately. If this is not done, it might become impossible to remove and could cause the external surfaces to alter or discolour. ^ The control panel should only be wiped with a damp cloth.
Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. , This dishwasher must not be used without all the filters in place.
To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b . ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet.
Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one).
With the help of the following guide, minor faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department. , Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations.
Problem Possible cause Remedy The buzzer is sounding. All the Programme indicators flash when the door is open. Fault code FXX shows in the display. There may be a technical fault. Switch the dishwasher off using the On/Off button K . After a few seconds: – Switch the dishwasher back on.
Water inlet/drain fault Problem Possible cause Remedy The dishwasher stops working shortly after the start of the programme. The buzzer sounds. The Inlet/drain check light 2 / 2 flashes when the door is opened. The stopcock is closed. – Open the stopcock fully.
General problems Problem Possible cause Remedy The indicators and time display are dark. Only the On/Off indicator K is flashing slowly. The indicators and the time display have switched off automatically to save energy (Standby mode). Press the On/Off button K .
Noises Problem Possible cause Remedy Knocking noise in the wash cabinet. A spray arm is knocking against an item in a basket. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet.
Unsatisfactory washing result Problem Possible cause Remedy The dishes are not clean. The dishes were not loaded correctly. See notes in "Loading the dishwasher". The programme was not powerful enough. Select a more intensive programme. See Programme chart.
Problem Possible cause Remedy Dishes, cutlery and glasses are not dry or are flecked. The amount of rinse aid may be insufficient, or the rinse aid reservoir empty. Replenish the reservoir, increase the dosage or change the brand of rinse aid (see "Before using for the first time, Rinse aid").
Problem Possible cause Remedy Glassware has a brown or blue tinge, and film cannot be wiped off. This may be caused by the detergent. Change your detergent. Glassware is dull and discoloured; film cannot be wiped off. The glasses are not dishwasher-proof.
Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet. , The plastic housing of the water connection contains an electrical component.
Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug.
Crockery Food deposits Action required Mixed, everyday crockery All normal food deposits This needs an adaptable programme... Shorter duration... Heat-sensitive glasses and plastic Fresh, easily remov.
Programme Detergent Compartment I 2) Compartment II 2) Sensor wash – 25 ml or 1 tab + Turbo Sensor wash gentle – 20 ml or 1 tab Light soiling 50°C – 25 ml or 1 tab 3) + Turbo ECO – 25 ml or 1 tab Pots & pans 75°C 10 ml 25 ml or 1 tab + Turbo 2) see "Detergent" 3) In some cases, tabs may not dissolve completely.
Programme Programme sequence Pre-wash Main wash °C Interim rinse Final rinse °C Drying 12 Sensor wash Variable programme sequence, sensor controlled adjustment according to the amount of crockery an.
Consumption 2) Duration 2) Energy Water Cold water connection (15 °C) kWh Hot water connection (55 °C) kWh Litres Cold water connection (15 °C) h:min Hot water connection (55 °C) h:min 1.10 3) -1.60 4) 0.70 3) -1.00 4) 13.0 3) -22.0 4) 1:35-2:34 1:23-2:21 1.
Repairs In the event of any faults that you cannot remedy yourself, please contact: – Your Miele dealer, or – the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, from the Miele Spare Parts Department or via the Internet at www.miele-shop.com (some may be supplied as standard, depending on model).
Electrical connection U.K. , All electrical work must be carried out by a suitably qualified and competent person, in accordance with current local and national safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
The Miele waterproof anti-leak system Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply , Water in the dishwasher must not be used as drinking water.
Drainage – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm.
Dishwasher model Standard XXL Height 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm 59.8 cm Width of building-in recess 60 cm 60 cm Depth 57 cm 57 cm Weight Max.
74.
75.
Alteration rights reserved/ G4280/G4285 / 2712 M.-Nr. 09 416 500 / 00.
An important point after buying a device Miele M.-Nr. 09 416 500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele M.-Nr. 09 416 500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele M.-Nr. 09 416 500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele M.-Nr. 09 416 500 you will learn all the available features of the product, as well as information on its operation. The information that you get Miele M.-Nr. 09 416 500 will certainly help you make a decision on the purchase.
If you already are a holder of Miele M.-Nr. 09 416 500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele M.-Nr. 09 416 500.
However, one of the most important roles played by the user manual is to help in solving problems with Miele M.-Nr. 09 416 500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele M.-Nr. 09 416 500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
