Instruction/ maintenance manual of the product G 1022 SCi Miele
Go to page of 68
Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time.
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Appliance overview .................................................5 Control panel ....................................................
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Detergent ........................................................3 2 Adding detergent .........................................
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Repairs .......
Appliance overview a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Filter combinat.
Control panel a Programmes b Time display c Extra options with indicator lights d Programme sequence indicators e On/Off button K f Check/Refill indicators g Start/Stop button with indicator light h D.
This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time.
Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Under no circumstances should you use a damaged appliance. A damaged appliance could be dangerous. ~ The dishwasher must only be plugged into the electricity supply via a suitable switched socket.
~ This appliance may only be installed in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer. ~ The plastic housing of the water connection contains an electrical component.
Installation ~ The dishwasher must be installed and connected in compliance with the installation diagram supplied. ~ The dishwasher must be correctly aligned to ensure problem-free operation.
~ Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener. Make sure you have picked up the correct packet of dishwasher salt before filling .
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your water supply is suitable, this dishwasher can be connected to hot water for further economies.
To open the door ^ Press the release catch inside the door grip upwards and pull the door open. If the door is opened during operation all functions are automatically interrupted. To close the door ^ Push the baskets right in. ^ Then lift the door upwards and push until it clicks into position.
Water softener In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in the build-up of calcium deposits on crockery and in the dishwasher. Mains water with a hardness level higher than 0.7 mmol/l (4 °d – German scale) needs to be softened.
To programme the water hardness level Each time a button is pressed, one of the indicator lights will flash and light up in the control panel. However, only the indicator lights mentioned in the following programming process stages are significant. The programming procedure can be cancelled at any time by pressing the On/Off button K .
°d German scale mmol/l °f Value displayed 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37-45 46-60 61-70 0.2 0.4 0.5 0.7 0.9 1.1 1.3 1.4 1.6 1.8 2.0 2.2 2.3 2.5 2.7 2.9 3.1 3.2 3.4 3.6 3.8 4.0 4.
Miele branded products are available from the Miele Spare Parts Department or via the internet at www.miele-shop.com. Before using the appliance for the first time you require: – Approx. 2 litre of water, – Approx. 2 kg dishwasher salt, – Domestic dishwasher detergent, – Rinse aid formulated for domestic dishwashers.
^ Remove the lower basket and unscrew the salt reservoir cap. Only open the salt reservoir when you want to fill it with dishwasher salt as water or salt solution will run out of the reservoir when the cap is removed. ^ Fill the reservoir with approx.
Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically.
^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid reservoir during a programme. ^ Wipe up any spilled rinse aid.
Setting the rinse aid dosage You can adjust the rinse aid dosage for best results. The rinse aid dosage can be set from approx. 0-6 ml. It is set to a recommended setting of approx.
Note Remove coarse food residues from crockery. There is no need to rinse items under running water. , Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher.
Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher.
Upper basket , For safety reasons, do not operate the dishwasher without the upper and lower baskets in place. ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc. Shallow pans or casserole dishes can also be placed in the upper basket.
Universal support (depending on model) This support is designed to hold tall glasses and glasses with stems securely. ^ Lower the support and lean tall glasses against it.
Adjusting the upper basket In order to gain more space for taller pieces of crockery in the bottom or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low.
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place delicate glassware in the lower basket. Dishwashers with cutlery tray Dishwashers with cutlery basket Hinged spikes The spikes are used for washing plates and saucers.
Removable spiked insert You can remove the spiked insert to make more room for larger items of crockery, e.g. a large, flat pot, or another type of insert. To remove the insert a ^ Pull it upwards by the handle as shown. To replace the insert b ^ Fit the insert into the lower basket with the hooks going under the long cross-piece as illustrated.
Cutlery Cutlery tray (depending on model) ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Cutlery basket (depending on model) ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. ^ Place small spoons in the individual slots to either side of the cutlery basket.
Detergent , Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Miele branded dishwasher cleaning products are available from the Miele Spare Parts Department or via the Internet at www.
, Avoid inhalation of powder detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled.
Switching on ^ Make sure the spray arms are not obstructed. ^ Close the door. ^ Open the stopcock, if it is closed. ^ Switch the dishwasher on with the On/Off button K . The Start/Stop indicator light flashes and the indicator light comes on next to the last programme selected.
Time display The duration of the programme selected appears in hours and minutes in the Time display before the programme begins. During the programme the time left until the end of the programme is displayed. The time displayed may vary with the same programme.
Unloading the dishwasher Dishes tend to break and chip more easily when they are hot. Allow the dishes to cool until they are comfortable enough to handle before unloading them. If you open the door fully after switching off, the dishes will cool much faster.
Extra options The "Extras" button is used for selecting the "Turbo" and "Combi tabs" options. ^ Switch the dishwasher on with the On/Off button K . The Start/Stop indicator light will flash. ^ Press the "Extras" button repeatedly until the indicator light for the option you want comes on.
Delay start The start time of a programme can be delayed, e.g. to benefit from economy rates of electricity. A delay start time of between 30 minutes and 24 hours can be selected. With a delay start time of between 30 minutes and 9 hours 30 minutes, the time is set in 30 minute increments.
The time starts counting down until the programme start time: in 1 hour steps for delay start periods of over 10 hours, and in minutes for delay start periods of under 10 hours. At the end of the delay period, the programme selected begins automatically.
Factory default setting If you have altered any settings from the factory default, you can re-set them back to the factory default settings as follows: ^ Switch the dishwasher off with the On/Off button K . ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K .
Adjust Sensor wash You can adjust the Sensor wash programme so that it will remove stubborn soiling in a lightly soiled load. ^ Switch the dishwasher off with the On/Off button K . ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K .
Check your dishwasher regularly (approx. ever y4-6 months). This way faults and problems can be avoided. Miele branded cleaning and conditioning products are available from the Miele Spare Parts Department or via the Internet at www.miele-shop.com. , The external surfaces of the dishwasher are susceptible to scratching.
Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. , The dishwasher must not be used without all the filters in place.
To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b . ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet.
Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one).
With the aid of the following guide, faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Miele Service Department. , Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations.
Problem Possible cause Remedy The Wash/Rinse, Drying and End indicator lights flash simultaneously. Fault code FXX shows in the display. There may be a technical fault. – Clean the water inlet filter and clean the drain pump and non-return flap as described in "Maintenance".
The dishwasher does not fill/drain. Problem Possible cause Remedy The Inlet/Drain check indicator flashes. The stopcock is closed. Open the stopcock fully. The dishwasher stops during a programme. The Inlet/Drain check indicator flashes. Fault code FXX shows in the display.
General problems Problem Possible cause Remedy The display is dark. The time display switches off automatically in Standby Mode to save energy. Press any button to come out of Standby mode. Detergent residue is left in the dispenser at the end of a programme.
Noises Problem Possible cause Remedy Knocking noise in the wash cabinet. A spray arm is knocking against an item in a basket. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet.
Unsatisfactory washing result Problem Possible cause Remedy The dishes are not clean. The dishes were not loaded correctly. See notes in "Loading the dishwasher" The programme was not powerful enough. Select a more intensive programme. See "Programme chart".
Problem Possible cause Remedy Dishes, cutlery and glasses are not dry or are flecked. The amount of rinse aid may be insufficient, or the rinse aid reservoir empty. Replenish the reservoir, increase the dosage or change the brand of rinse aid. See "Before using for the first time".
Problem Possible cause Remedy Glassware has a brown or blue tinge, and film cannot be wiped off. This may be caused by the detergent. Change your detergent. Glassware is dull and discoloured; film cannot be wiped off. The glassware is not dishwasher-proof.
Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet. , The plastic housing of the water connection contains an electrical component.
Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug.
Crockery Food deposits Action required Mixed, everyday crockery All normal food deposits This needs an adaptable programme... Shorter duration... Heat-sensitive glasses and plastic Fresh, easily removed food deposits This needs a short programme... Mixed crockery This needs a gentle programme with glass care.
Programme Detergent Compartment I 2) Compartment II 2) Sensor wash – 25 ml or 1 tab + Turbo option Quick wash 40°C – 25 ml or 1 tab 3) Sensor wash gentle – 25 ml or 1 tab Light soiling 50°C .
Programme Programme sequence Pre-wash Main wash °C Interim rinse Final rinse °C Drying 12 Sensor wash Variable programme sequence, sensor controlled adjustment according to the amount of crockery an.
Consumption 1) Duration 1) Energy Water Cold water connection (15 °C) kWh Hot water connection (55 °C) kWh Litres Cold water connection (15 °C) h:min Hot water connection (55 °C) h:min 1.10-1.60 0.70-1.00 13-22 1:35-2:34 1:23-2:21 0.70 0.22 13 0:38 0:30 0.
Repairs In the event of any faults that you cannot remedy yourself, please contact: – Your Miele dealer, or – the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, the Spare Parts Department or online at www.
Electrical connection U.K. , All electrical work must be carried out by a suitably qualified and competent person, in accordance with current local and national safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
The Miele waterproof anti-leak system Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply , Water in the dishwasher must not be used as drinking water.
Drainage – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm.
Dishwasher model G 1XXX G 2XXX Height freestanding 84.5 cm (adjustable +3.5 cm) - Height built-in 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm 59.
66.
67.
Alteration rights reserved/ G1222/G1232/G2222/G2232 / 0410 M.-Nr. 07 502 150 / 01.
An important point after buying a device Miele G 1022 SCi (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele G 1022 SCi yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele G 1022 SCi - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele G 1022 SCi you will learn all the available features of the product, as well as information on its operation. The information that you get Miele G 1022 SCi will certainly help you make a decision on the purchase.
If you already are a holder of Miele G 1022 SCi, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele G 1022 SCi.
However, one of the most important roles played by the user manual is to help in solving problems with Miele G 1022 SCi. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele G 1022 SCi along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
