Instruction/ maintenance manual of the product F 1911 Vi Miele
Go to page of 80
Operating and Installation Instructions Freezer with Ice Maker F 1801 Vi, F 1811 Vi F 1901 Vi, F 1911 Vi To prevent accidents and appliance damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS .................................4 Guide to the freezer ................................................8 Before use ......................................................1 0 Turning the appliance On/Off .................
Caring for the environment .........................................4 6 Installation ......................................................4 7 Installation site ....................................................4 7 Stainless steel panels ...........
When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual.
Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the door closed until the appliance is completely installed and secured per installation instructions. ~ This appliance must be installed and connected in compliance with the installation instructions.
~ Persons who lack physical, sensory or mental abilities, or experience with the machine should not use it without supervision or instruction by a responsible person. ~ To reduce the risk of injury, do not allow children to play in, on or near the appliance, especially in the door hinge area.
Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable. ~ Take off the door. ~ Leave the shelves in place so that children may not easily climb inside. ~ Consult with your municipal policy on recycling.
a Door shelves (height adjustable) b Shelves (height adjustable) c Ice cube maker d Ice cube container e Control panel f Main switch to turn the appliance On/Off g Freezer baskets h Water filter Guide.
Control panel a Access button " p " b Temperature display X colder; Y warmer Allows you to set the desired temperature in the freezer c On/Off sensor button for the SuperCool function d On/O.
Before using for the first time ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. If the appliance was transported to the installation site horizontally, leave the appliance standing upright for approx.
Using the settings This appliance is operated with the use of touch keys activated by a finger. – An available button will appear white. – A selected button will appear yellow. ^ Touch the access button " p "s oi t turns yellow. On the control panel you will see additional sensor buttons to operate the appliance.
Turning the button sound On/Off If you prefer the buttons to be silent when touched the button sound can be turned off. ^ Touch the access button " p "s oi t turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button " p " again so it turns white.
Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions need to be taken: ^ Shut off the water supply lin.
The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door. The alarm system is always operational, it does not need to be switched on.
Setting the temperature ^ Touch the access button " p "s oi t turns yellow. ^ Use the X and Y buttons next to the temperature display to set the temperature warmer or colder. Tap the X and Y sensor buttons to raise/lower the temperature 1°, or hold it down to move through the temperature range more quickly.
Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ Touch the access button " p "s oi t turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button " p " again so it turns white.
Freezing food Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food. Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long.
Defrosting Frozen food can be defrosted in different ways: – in a microwave oven, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep the other food cold), – in a steam oven. Poultry It is especially important to observe proper hygiene when defrosting poultry.
Freezing tips – The following are examples of foods suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, pastry/dough, leftovers, and a range of pre-cooked meals.
When the SuperCool function is activated, the appliance is cooled as cold as possible (to a factory-preset temperature). SuperCool The SuperCool function is ideal for freezing large quantities of unfrozen food. Ideally the function should be switched o n4-6 hours before the food is placed in the freezer.
For the automatic ice cube maker to operate, it must be connected to the household water supply. See "Plumbing". Turning on the ice cube maker ^ Make sure that the ice cube container is under the ice cube maker, as far as possible. Ice cubes will not be produced unless the container is completely closed.
The freezer defrosts automatically. The moisture generated in the appliance collects in the evaporator. It is automatically defrosted and dissipated by the condenser periodically. This automatic defrosting system enables the freezer to remain permanently ice-free, while ensuring that the food stored in the freezer stays frozen.
Moving the shelves The shelves can be adjusted according to the height of the food. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Pull the shelf forward. ^ Move the shelf to the desired height, then insert the (rear) hooks into place.
Ice cube container The ice cube container is set on telescopic tracks, and can be removed for loading, unloading and cleaning. ^ Slide the container forward until resistance is felt. ^ On both sides of the container, pull the latches (see arrow) upward and lift the container out of the freezer.
To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance. Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents.
Before cleaning ^ Use the main switch to turn the appliance off completely. The main switch is located on the right side underneath the control panel. ^ Unplug the power cord. ^ Remove any food from the appliance and store it in a cool place. ^ Take out any removable parts, e.
Ventilation slits ^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. Door seals Do not use any oils or grease on the door seals. This may cause the seals to deteriorate and become porous over time.
Changing the light bulb The lighting automatically switches off after the door has been open for approx. 5 minutes. This is not a fault. After the bulb has cooled for a short time it will turn on again. If the light does not come on when the door is opened briefly, the light bulb should be changed.
Side lighting ^ Turn the light cover counterclockwise and pull out. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold with a soft cloth. ^ Pull the defective light bulb from the socket. ^ Place the new bulb in the socket.
The Appliance is supplied with an active charcoal filter which improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water. Additional water filters are available from Miele. It is important to change the water filter regularly.
Exchanging the water filter Note: Air trapped in the system may cause water and the filter cartridge to eject forcefully. Use caution when removing. ^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1 . ^ Pull the used filter cartridge out of the appliance, 2 .
^ After the filter change the filter indicator in the display still flashes. The change must be be confirmed in the electronic. Confirming the filter change ^ Press and hold the filter change sensor button. ^ At the same time place a finger on the access button.
Water filter 33 State of California Department of Public Health Water Treatment Device Certificate Number Date Issued: March 10, 2006 T rad e mark /M od e l D e s i g nat i on R e p l ac e m e nt E l .
Water filter 34 To a capacity of 739.68 gallons (2800 liters). * Based on the use of Cryptosporium parvum oocysts Performance Data Sheet For Filter Model 07134220 System tested and certified by NSF In.
This product F 1801 Vi, F 1811 Vi (KIMSDF30US) / F 1901 Vi, F 1911 Vi (KIMSDF36US) is tested and certified by WQA against ORD0902 for California "lead free" compliance.
With the aid of the following guide minor problems can be corrected without a ser - vice call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty.
General problems Issue Possible fault Solution Water is flowing out of the appliance. Close the shut-off valve immediately. Check whether the water pipe in the appliance is defective. Contact Miele Technical Service. Check whether the water pressure is too low.
Alarm / Indicator warnings Issue Possible fault Solution The alarm is going off. The appliance door(s) have been open for longer than 5 minutes. Close the door. The alarm is ringing and the "alarm" indicator is flashing. The door is not closed.
Problems with the ice maker Issue Possible fault Solution The ice cube maker will not switch on. The appliance is not plugged in. Check that the appliance is connected to the power supply.
Problems with the ice maker Issue Possible fault Solution The ice cubes are small. Other domestic appliances that use water are in operation. Avoid using such items as a dishwasher, washing machine or shower at the same time. Check whether the water filter needs changing.
Problems with the ice maker Issue Possible fault Solution The ice maker is not producing enough ice or the ice cubes are misshapen. Check the water pressure. The water pressure must be between 25 and 120 psi (1.72-8.25 bar). Contact a plumber. Check that the freezer temperature is too high.
The appliance is making noises. Issue Possible fault Solution Brrrrr... Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on. These noises are not a fault. The noise of the compressor and the coolant circulating in the system is unavoidable.
In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
44.
Installation instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use.
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc.
Have the appliance installed by a qualified technician, according to the enclosed installation instructions. WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the door closed until the appliance is completely installed and secured as per the installation instructions.
Base A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements. The approx. weight of a fully loaded machine is: F 18X1 Vi .
Stainless steel panels Stainless steel door panels and toe-kick covers are available from Miele. Custom door panels This appliance is compatible with all styles and designs of kitchen cabinetry. The total weight of the decorative panel(s) must not exceed the following: F 18X1 Vi .
Installation with partition using the "Merging Kit" The minimum thickness of the partition is 5 / 8 " (16 mm). If there is a partition with a thickness from 5 / 8 " (16 mm) to 6 5 .
Front panel gap kit (optional accessory) Two adjacent doors can be attached instead of one large door. To connect these doors on the rear, a metal strip can be purchased as an optional accessory. Contact Miele. When attaching the metal strip to the furniture doors, observe the maximum length of the screws and the position of the drill holes.
Door dimensions (open 115°) ABC D F 18X1 Vi 32 5 / 8 " (829 mm) Door front max. 1 1/2" (38 mm) Door handle* 14 5 / 16 " (363 mm) F 19X1 Vi 38 11 / 16 " (982 mm) Door front max. 1 1/2" (38 mm) Door handle* 16 7 / 8 " (428 mm) *The dimensions of the door fronts and handles will vary according to each individual kitchen.
Niche dimensions Niche width (A) F 18X1 Vi 30" (762 mm) F 19X1 Vi 36" (915 mm) Dimensions 53.
Power supply and water connection A F 18X1 Vi 15" (381 mm) F 19X1 Vi 18" (458 mm) Door front dimensions AB F 18X1 Vi 79 1 / 8 " 2029 mm 29 3 / 4 " 756 mm F 19X1 Vi 79 1 / 8 " 2029 mm 35 3 / 4 " 908 mm 4" - 5 3/16" (102 - 132 mm) Dimensions 54 1.
Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation.
Aligning the housing unit The housing unit must be carefully aligned using a spirit level before installing the appliance. The unit corners must be at right angles, as otherwise the furniture door will not align correctly with the 4 corners of the appliance.
^ Do not remove the installation supports from the appliance door. They will be used later in the installation niche. There are transportation safety devices inside the appliance to protect the shelves and storage compartments until installation is complete.
^ Push the module into the slot until it locks into place. ^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light e will come on. The indicator light will display different colors one after the other; any control light at the end indicates that the module was correctly installed.
Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are marked alphabetically. The bag needed for each step will be marked with its respective letter.
^ Drill pilot holes: – 1 / 8 "( 3m m )f o r5x6 0m m wood screws – 1 / 16 "( 2m m )f o r4x1 5m m wood screws ^ Tightly secure the anti-tip brackets in the niche. Be certain that the screws penetrate through the flooring and into the wall plate a minimum of 3 / 4 " (19 mm).
Securing an alternative anti-tip device If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. If possible, always screw the wooden beam to existing studs.
Sliding the appliance into the installation niche If a side-by-side installation is desired, connect the two appliances together. See the Installation Manual included with the "Merging Kit". ^ Unscrew the plinth. ^ To protect the corners of the installation space, attach the supplied edge protector a on both sides with adhesive tape.
Aligning the appliance ^ Align the appliance with the custom front. The installation aids e on the appliance door have been designed for custom door thicknesses of 3/4" (19 mm) and 1 1/2" (38 mm). The height-adjustable feet at the front and rear can all be adjusted from the front: – Front feet: Adjust with a rachet 5/16" (8 mm) f .
Attaching the appliance to the installation niche ^ Screw the attachment plate lugs h to the overhead furniture/fixtures. If there is no way to attach the top of the appliance, it can be attached to the sides of the installation niche. ^ Pull out the plate side lugs i .
For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Take the peg from the "Side-by-side Merging Kit" and insert it halfway into the filler strip rail on the left-side appliance.
Preparing the custom door ^ Open the appliance door. ^ Unscrew the installation supports n from the appliance door. ^ Loosen the remaining screws from the strips o on each side of the door, then remove. ^ Set aside the screws and side strips o - you will need them again later.
^ Mark the distance X on the back-side of the custom door. ^ Also calculate and mark the center of the custom door Y . ^ Remove the mounting frame from the appliance door and position it according to the markings on the custom door. ^ Pre-drill the holes.
Attaching and aligning the custom door front ^ Open the door and hang the custom door with the mounting frame over the threaded bolts p . ^ Put the side strips o back into place and screw them completely down on both sides of the appliance door. Bag E contains spare screws for this purpose.
Attaching the fixing brackets (Only for appliances using the "Front panel gap kit".) The fixing brackets are used to secure the custom door front to the bottom of the appliance door. ^ Open the appliance door all the way. ^ Slightly loosen the screw (1.
^ Insert the cover strip into the space between the appliance and the side panel. For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only. ^ Attach the light switch cover. Attaching the toe-kick cover The maximum height of the toe-kick cover is 4" from the top of the floor.
Mounting the air separator The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ If necessary, shorten the three parts of the air separator.
All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. The water quality must conform to country requirements for drinking water. – The appliance is only suitable for connection to the cold water supply.
Preparing the water connection The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water.
Connecting the water supply When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit. When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage.
, Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem.
Accessing the RemoteVision control panel ^ Touch the access button " p "s oi t turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button " p " again so it turns white. Only the access button " p " is visible.
MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network.
79.
Alteration rights reserved / 3712 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
An important point after buying a device Miele F 1911 Vi (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele F 1911 Vi yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele F 1911 Vi - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele F 1911 Vi you will learn all the available features of the product, as well as information on its operation. The information that you get Miele F 1911 Vi will certainly help you make a decision on the purchase.
If you already are a holder of Miele F 1911 Vi, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele F 1911 Vi.
However, one of the most important roles played by the user manual is to help in solving problems with Miele F 1911 Vi. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele F 1911 Vi along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
