Instruction/ maintenance manual of the product CS1312 Miele
Go to page of 44
Operating and installation instructions Open barbeque grill CS 1312 CS 1322 To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
Guide to the appliance .............................................4 CS 1312 ..........................................................4 CS 1322 ..........................................................5 Accessories supplied ........................
Installation of several appliances ....................................3 2 Fixing the spring clamps and spacer bars ............................3 4 Installing the appliance(s) ..........................................3 6 General installation tips ...
CS 1312 a Grill rack b Front heating element c Rear heating element d Lava rock container e Drain tap f Symbols to indicate which heating element the control is for g Display Controls for the heating .
CS 1322 a Grill racks b Front heating element c Rear heating element d Lava rock container e Drain tap f Symbols to indicate which heating element the control is for g Display Controls for the heating.
Accessories supplied Additional accessories can be ordered at extra cost. See "Optional accessories" for further details on ordering. Lava rocks Tongs Brush Guide to the appliance 6.
This appliance complies with all current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time.
Safety with children ~ This appliance is only intended for use by adults who have read these instructions. It is not a toy! To avoid the risk of injury, keep children well away and do not allow them to play with it or use the controls. They will not understand the potential dangers posed by it.
Technical safety ~ Before installation, check the appliance for visible signs of damage. Under no circumstances should you use a damaged appliance. It could be dangerous. ~ The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system.
~ This appliance may be connected via a fused plug and switched socket. If you wish to connect it to an fused spur connection unit, or if the appliance is supplied without a plug, it must be installed and connected by a suitably qualified and competent person in strict accordance with current local and national safety regulations.
~ Do not use the appliance as a resting place for anything else. When the appliance is switched on either deliberately or by mistake, or when there is residual heat present, there is the risk of metal objects heating up, with a danger of burning. Depending on the material, other objects left on the appliance could also melt or catch fire.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service" section of this booklet.
Grill chart The times given in the table serve as a guide, based on a pre-heated grill at settings 9 to 12. The grilling time required will depend on the type of food, its texture and thickness as well as personal taste.
Food Time in minutes Vegetables Aubergines 6 - 8 Jacket potatoes, pre-cooked 10 - 20 Vegetarian kebabs 5 - 6 Corn on the cob, pre-cooked 5 - 8 Peppers, cut into strips 2 - 3 Tomato halves 2 - 4 Fruit .
To prepare the grill The grill can be used with or without the lava rocks. Without the lava rocks the rising steam keeps the food being grilled moist. Grilling with the lava rocks creates a particularly intensive aroma. ^ Check that the drain tap is closed.
Grilling When grilling, keep an eye on the level of water in the trough. If necessary, add more water. When grilling or keeping food warm, do not use grill pans, griddles, saucepans or similar on the open grill, and never cover the rack(s) (e.g. with aluminium foil).
Overheating protection A safety cut-out automatically switches the appliance off if the water level drops too low. ^ Add some cold water. As soon as the appliance has cooled down, the heating elements switch back on again and you can continue grilling.
, Do not use a steam cleaning appliance to clean this appliance. The steam could reach the electrical components and cause a short circuit. Clean the appliance regularly, preferably after each use. Allow the appliance to cool down to a safe temperature before cleaning.
Stainless steel The ceramic and stainless steel hob cleaner is suitable for cleaning stainless steel surfaces (see "Optional accessories"). To help prevent resoiling, we recommend a stainless steel conditioner (see "Optional accessories").
Grill trough Clean the grill trough after each use. ^ After grilling, allow the water in the trough to cool down before draining it. ^ Place a container large enough to take the contents of the trough under the drain. ^ Open the drain tap under the grill by turning it anti-clockwise a .
Installation work and repairs to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). Repairs and other work by unqualified persons could be dangerous.
Miele offers a range of useful accessories designed for your appliance. These can be ordered via the internet at www.miele-shop.com, or from Miele (see back cover for contact details) or from your Miele dealer.
Cleaning and care products Ceramic and stainless steel hob cleaner 250 ml Removes heavy soiling, limescale deposits and light discolouration Stainless steel conditioning agent 250 ml Removes water marks, flecks and finger prints. Helps keep the appliance looking good for longer.
Fit the wall units and extractor hood before fitting the barbecue grill to avoid damaging the surface. ~ The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort.
Safety distance above the grill A minimum safety distance must be maintained between the hob and the cooker hood above it. See the cooker hood manufacturer’s operating and installation instructions for details.
Safety distances to the sides of the grill Ideally the grill should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall at one side. On the other side, however, no unit or divider should stand higher than the built-in appliance (see illustrations).
Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.
CS 1312 a Spring clamps b Front c Casing depth d Casing depth plus depth of mains connection box with mains connection cable, L = 2,000 mm e Drain tap Appliance and building-in dimensions 29.
CS 1322 a Spring clamps b Front c Casing depth d Casing depth plus depth of mains connection box with mains connection cable, L = 2,000 mm e Drain tap Appliance and building-in dimensions 30.
^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall , as well as from any tall unit or side wall to the right or left of the appliance(s). See "Safety instructions for installation".
When installing two or more appliances next to each other a spacer bar b must be used between each one. See "Fixing the spring clamps and spacer bars". Worktop cut-out - two appliances Worktop cut-out - three appliances To calculate the cut-out width (D) required: Add up the widths of each appliance (e.
a Spring clamps b Spacer bars c Gap between spacer bar and worktop d Sealing strip The illustration shows a worktop cut-out with spring clamps a and spacer bars b for 3 appliances.
Wooden worktops ^ Position the spring clamps supplied a and spacer bars b on the top edge of the cut-out in the positions marked. ^ Secure the spring clamps and spacer bars with the 3.
Granite and marble worktops The screws are not required for granite or marble worktops. ^ Position and secure the spring clamps a and spacer bars b using strong, double-sided adhesive tape c . ^ Apply silcone to the side edges and the lower edges of the spring clamps a and spacer bars b .
^ Feed the connection cable down through the cut-out. ^ Starting at the front, position the appliance in the worktop cut-out. ^ Using both hands, press down evenly on the sides of the appliance until it clicks into position. When doing this make sure that the seal under the appliance sits flush with the worktop on all sides.
Do not use any sealant unless expressly instructed to do so. The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop. Do not use sealant between the frame of the top part of the appliance and the worktop.
All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK).
Important The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system, which complies with local and national regulations.
In the event of any faults which you cannot remedy yourself, or if the appliance is under guarantee, please contact: – Your Miele dealer, or – the Miele Customer Contact Centre (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
41.
42.
43.
Alteration rights reserved/ 2110 M.-Nr. 07 180 420 / 09.
An important point after buying a device Miele CS1312 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele CS1312 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele CS1312 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele CS1312 you will learn all the available features of the product, as well as information on its operation. The information that you get Miele CS1312 will certainly help you make a decision on the purchase.
If you already are a holder of Miele CS1312, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele CS1312.
However, one of the most important roles played by the user manual is to help in solving problems with Miele CS1312. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele CS1312 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
