Instruction/ maintenance manual of the product CS 1122 Miele
Go to page of 40
Operating and Installation Instructions Ceramic Combiset CS 1112 CS 1122 To prevent accidents and appliance damage, read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS .................................3 Description of the combiset .........................................7 CS 1112 ..........................................................7 CS 1122 .......................................
WARNING- When using your gas appliance follow basic precautions, including the following: This gas combiset conforms to all uniform safety codes and regulations.
Technical safety ~ Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Be sure your appliance is properly installed and grounded by a qualified technician.
~ Be sure that the power cord does not come in contact with any "hot spots" after installation. Safety ~ DO NOT TOUCH THE COOKING AREA OR THE VICINITY AROUND THE COOKING AREA - During operation, the cooking area and its surroundings will get hot and can cause burns.
~ Make certain that the power cords of small appliances do not come in contact with the appliance. The insulation of the cable could become damaged. Danger of electric shock! ~ Be careful not to drop anything on the ceramic surface of the combiset. Even lightweight objects may cause damage.
CS 1112 a Variable burner : C 4" or 7" (100 mm or 180 mm) - Power: 700 W or 1800 W b Standard burner : C 5 11 / 16 " (145 mm) - Power: 1200 W c Burner indicators d Display Control knobs.
CS 1122 a Extended burner C 7" or 7" x 10 7 / 16 " (180 mm or 180 mm x 265 mm) - Power: 1500 W / 2400 W b Standard burner C 5 11 / 16 " (145 mm) - Power: 1200 W c Burner indicators.
Clean the combiset ^ Remove any protective coverings or stickers. ^ Before using for the first time, clean the appliance with a damp cloth and dry with a soft cloth. Do not use liquid dish soap to clean the combiset, this may cause permanent blue discolorations.
One-ring burners use one heating strip, and two-ring burners and grill zones use two heating strips. Depending on the model, the heating strips may be separated by a certain distance.
Turning a burner On/Off ^ To turn a burner on , press the control knob down and turn it clockwise a to the desired setting. ^ To turn a burner off , turn the control knob counterclockwise b to "0". Do not turn a burner on without pressing the control knob down, and do not turn the knob past "12" or n to reach "0".
Residual Heat Indicator When a cooking zone is switched on, the On/Off indicator will light followed by the residual heat indicator. When the cooking zone is switched off, the On/Off indicator goes out. The residual heat indicator will turn off once the cooking zone is safe to the touch.
Settings Use for Power level* Melt butter, chocolate, etc. Dissolving gelatine Prepare yogurt 1-2 Warming small quantities of food/liquid Keeping delicate dishes warm Cooking rice, Thawing frozen vegetables 1-3 Warming liquid or half-set foods Thickening sauces, e.
Overheat protection Each cooking zone is equipped with a temperature limiter. This feature automatically turns off the heating element before the glass ceramic becomes too hot. Once the ceramic surface has cooled to a safe temperature the heating element will automatically turn back on.
Following these tips will allow you to make the most of your ceramic combiset. The cooking surface The ceramic combiset is made of an extremely hard and durable material. The surface is scratch resistant, not scratch proof. Avoid using cookware with ridged bottoms.
Copper bottom and aluminum pans may leave a residue on the combiset in the form of metallic lines. This is normal. These lines can be removed using a non-abrasive ceramic combiset cleaner or a shielded scraper blade. Be sure to clean the combiset after each use.
Do not use a steam cleaner to clean this appliance. Steam could penetrate electrical components and cause a short circuit. Pressurized steam could cause permanent damage to the surface. Do not use any sharp pointed objects which could damage the seal between the ceramic surface, the surrounding frame and the countertop.
Ceramic surfaces ^ Wipe off any soiling using a damp cloth. Stubborn soiling is best removed with a shielded scraper blade. ^ Apply a ceramic cleaner (available from Miele) using a soft cloth or paper towel.
, Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. What if the appliance does not heat up after it is turned on? Possible fault Solution The circuit breaker has tripped.
In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance.
MieleCare (USA only) MieleCare , our Extended Service Contract program; gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts.
22.
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and appliance damage read these instructions before installation or use.
Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. The minimum distances given in these Installation Instructions must be observed in order to ensure safe operation. Failure to do so increases the risk of fire.
Safety distances above the appliance The minimum safety distance given by the hood manufacturer must be maintained between the combiset and the hood above it.
Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations, while maintaining the required safety distances shown.
Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out and the covering, since high temperatures can damage these materials.
Installation dimensions CS 1112 a Spring clips b Appliance front c Installation height d Power supply box with connection cable ,L=7 8 3/4" (2000 mm) e Rating label Installation 28.
Installation dimensions CS 1122 a Spring clips b Appliance front c Installation height d Power supply box with connection cable ,L=7 8 3/4" (2000 mm) e Rating label Installation 29.
Cut out ^ Make the countertop cut-out for the desired number of appliances according to the dimensions drawings. Remember to maintain a minimum safety distance from the back wall , as well as from any tall unit or side wall to the left or right of the combiset.
Installation of multiple appliances When installing more than one combiset appliance, a support bar b must be installed between the appliances. Countertop cut-out two appliances For the installation of two appliances the width of the countertop cut-out D is the sum of A and C.
Sample calculations for a countertop cut-out for three appliances A appliance width minus 5/16" (8 mm) B appliance width C appliance width minus 5/16" (8 mm) D Countertop cut-out 11" (2.
a Spring clips b Support bars c Space between support bar and countertop d Cover The illustration represents the attachment of spring clips a and support bars b for 3 appliances. An additional support bar is required for each additional appliance. The position for attachment of an additional support bar depends on the width of appliance B .
Attach the spring clips and support bars Wood or solid surface countertops ^ Place the supplied spring clips a and the support bars b at the marked positions as shown above, by laying them on the upper edge of the cut-out and then securing them with the 1 / 8 " x 1" (3.
Granite countertop The screws are not needed for granite countertops. ^ Position and attach the spring clips a and support bars b with strong, double-sided tape c . ^ Coat the side and lower edges of the spring clips between a and b with silicone. ^ Fill the space e between the support bars b and the countertop with silicone.
Installing the appliance(s) ^ Feed the power cord down through the cut-out. ^ Place the front edge of the appliance into the cut-out. ^ With a hand on each side of the appliance press down evenly on the edges until it clicks into position.
Sealing The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. If the appliance is sealed into position, the countertop or appliance could be damaged if it needs to be removed for maintenance or service.
, CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the main power or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards.
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of an old appliance Old appliances contain materials that can be recycled.
Alteration rights reserved / 3911 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
An important point after buying a device Miele CS 1122 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele CS 1122 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele CS 1122 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele CS 1122 you will learn all the available features of the product, as well as information on its operation. The information that you get Miele CS 1122 will certainly help you make a decision on the purchase.
If you already are a holder of Miele CS 1122, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele CS 1122.
However, one of the most important roles played by the user manual is to help in solving problems with Miele CS 1122. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele CS 1122 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
