Instruction/ maintenance manual of the product 05 714 400 Miele
Go to page of 64
Operating instructions f or dishw ashers It is essential to read the operating and installation instructions before installing, commissioning or using the machine, to avoid the risk of accidents or damage to the machine.
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Appliance overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Control panel . .
Operating the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Adding detergent .
Appliance overvie w 1 Upper spray arm (not visible) 2 Cutlery tray (depending on model) 3 Upper basket 4 W ater feed for middle spray arm 5 Middle spray arm 6 Lower spray arm 7 Four height adjustable .
Control panel 13 "On/Off" button 14 Programme sequence display 15 "Start" button 16 Programme selector 17 Check/Refill indicators 18 Child safety lock 19 Door release Guide to the .
This appliance conforms to current safety requir ements. Inappropriate use can however lead to personal injury and damage to property . Read the operating instructions carefully befor e starting to use this appliance. This way you will prevent the risk of accidents and damage to the appliance.
This equipment is not designed for maritime use or for use in mobile installations such as caravans, aircraft etc. However it may be suitable for such usage subject to a risk assess - ment of the installation being carried out by a suitably qualified engineer .
T ake care on dishwashers with a visible heater element (depending on model) Do not touch the heating element during or directly after the end of a programme. It will be hot. Danger of burning! Some plastic items could melt or catch fire if they wer e to come into contact with the heating element.
The Miele W aterproof System of fers protection fr om water damage, pro - vided the following conditions are met: – The dishwasher is correctly installed and plumbed in. – The dishwasher is properly main - tained and parts are replaced wher e it can be seen that this is necessary .
Disposal of the packing material The transport and protective packing has been selected from materials which are envir onmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
Before using the appliance f or the first time y ou require: – approx. 2 litr es of water , – approx. 2 kg dishwasher r eactivation salt, – domestic dishwasher detergent, – rinse aid formulated for domestic dishwashers. Every dishwasher is tested at the factory .
T o open the door ^ Press the r elease catch inside the door grip and pull forward. If the door is opened during operation all functions are automatically inter- rupted. T o c lose the door ^ Push the baskets right in, lift the door and push until it clicks into position.
W ater softener In order to achieve good cleaning r e - sults, the dishwasher needs to operate with soft water . Hard water results in the build-up of calcium deposits on crock - ery and in the dishwasher . Mains water with a hardness level higher than 0.
Programming the water har dness level ^ Switch the dishwasher off using the "On/Off" button. ^ T ur n the programme selector to the "Stop" position. ^ Press the "Start" button in and whilst holding it in switch the dishwasher on using the "On/Off" button.
^ Press the "Start" button. The "Start" indicator light will come on. ^ T ur n the programme selector to the "Stop" position. ^ Switch the dishwasher off using the "On/Off" button. The water hardness level is now stor ed in memory .
Filling the salt reservoir If the water in your area is very soft and constantly lower than 0.7 mmol/l (4 °d) you do not need to add dish - washer salt. The water softener must, however , still be programmed to corr espond to the water hardness level in your area.
Salt indicator The salt indicator light comes on to no - tify you that the reservoir is empty . ^ The reservoir should then be r efilled with dishwasher salt for reactivation. (See: Filling the salt reservoir). After the reservoir has been filled, the water softener is automatically reacti- vated the next time the dishwasher is run.
Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase. Rinse aid is poured into the storage r es - ervoir and the amount set is dispensed automatically .
^ Add rinse aid only until it is visible on the surface of the filter in the opening. The rinse aid reservoir holds appr ox. 130 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water would en- ter the rinse aid reservoir during a programme.
Setting the rinse aid dosage The dosage selector has settings from 1-6. It is set to "3" (3 ml) at the factory . Approx. 3 ml of rinse aid ar e then used per programme. This is a r ecom- mended setting. If spots appear on crockery and glass- ware: ^ Use a higher setting.
Note ^ Remove coarse food residues fr om crockery . There is no need to rinse items under running water . , Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher . Ash does not dissolve and is distributed in the wash cabinet.
Upper basket For small, lightweight, delicate items such as cups, saucers, glasses, des- sert bowls, etc. as well as plastic items which are heat r esistant.
Adjusting the upper basket In order to gain mor e space for taller pieces of crockery in the bottom or up - per basket, the upper basket can be adjusted on three levels with 2 cm be - tween each level. The upper basket can also be set at an angle with one side high and the other side low .
Lower basket For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place thin, delicate glassware in the lower basket. Delicate glassware can only be washed in the bottom of the dishwasher in a special lower bas - ket with a glassware insert.
Bottle holder The bottle holder , e.g. for milk and baby bottles, can be fitted in the lower basket in the area marked white in the illustra- tion. However , do not place a bottle holder in the corners. Water will not be able to access the bottles properly , and cleaning results will be impair ed.
Cutlery Dishwashers with a cutlery basket ^ Unsorted cutler y should be placed in the cutlery basket with the handles facing downwards to ensur e optimum spray water access. , However , to avoid the risk of in - jury cutler y with sharp points should be placed with the handles up - wards.
Spoon inserts for the cutlery basket Use the inserts supplied when washing heavily soiled spoons, e.g. tablespoons and serving spoons. The inserts separate the spoons to al - low a space between them so that they can be more easily accessed by water .
Dishwashers with a cutlery tra y (SC) For best results cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.This makes unloading much easier . Place the blades of knives and the prongs of forks between the holders. Spoons, on the other hand, should be placed with the handles between the holders.
Items not suitable f or dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher -proof and wooden handles may come loose after being washed in a dish - washer .
Detergent , Only use detergents formulated for domestic dishwashers. Do not use washing up liquid. ^ Y ou can use conventional powder de - tergent, tablets or liquid dishwasher detergent. Refer to the dosing instructions given by the manufacturer on the packag - ing.
Adding deter gent , Avoid inhalation of powder de - tergents and do not ingest dish - washer detergent! Dishwasher de - tergents contain irritant or corrosive ingredients. They can cause burning in the nose, mouth and throat if swal - lowed, or inhibit breathing.
Programme selection Choose your programme accor ding to the type of load and how dirty it is. In most cases this will be a Universal programme or a Universal plus programme. These programmes ar e ideally suited to everyday mixed loads with var ying de - grees of soiling.
Switching on ^ Make sure the spray arms are not ob- structed. ^ Close the door . ^ Open the stopcock, if it is closed. ^ Press the "On/Of f" button (13). The "Start" indicator light (15) will flash. Starting a programme ^ When selecting a programme, r efer to the programme chart at the end of the operating instructions.
At the end of a programme A programme has finished when the "End" indicator light comes on in the programme sequence display (14). The dishwasher can now be opened and unloaded (see "Unloading the dish - washer"). , Do not touch the heating ele - ment during or directly after the end of a programme.
Interrupting a programme A programme is interrupted as soon as the door is opened. If the door is closed again, the programme will continue fr om the point it was at before the door was opened. , W ater in the dishwasher may be hot. Danger of scalding! Only open the door if absolutely necessary and exercise extreme caution when doing so.
Drying heat In all programmes the drying process is assisted by the heating element. Drying heat is set as activated at the factory . Switching the heating elements off dur - ing drying will save approx. 0.1 kWh in electricity . The dishes are then dried with residual heat.
Unloading the dishwasher ^ Dishes tend to break and chip mor e easily when they are hot. Allow the dishes to cool until they are comfortable enough to handle before unloading them. ^ If you open the door fully after switch - ing off, the dishes will cool much faster .
Check your dishwasher regularly (approx. every 4 - 6 months). This way faults and problems can be avoided. Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabin.
T o clean the underside of the filter , the flap must be opened: ^ Pull back the yellow clip to do this. ^ Rinse all parts under running water , using a nylon brush if necessary . ^ Then close the flap so that the clip engages. Important: After cleaning make sure that the clip has pr operly engaged.
Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (appr ox. every 4 - 6 months). ^ Switch the dishwasher off befor e - hand. Remove the spray arms as follows: ^ T ake out the cutlery tray (if your dish - washer is fitted with one).
Cleaning the wash cabinet The wash cabinet is largely self-clean - ing, provided that the corr ect amount of detergent is always used. If, however , there are limescale or grease deposits in the cabinet these can be removed with a pr oprietary dishwasher cleaner .
Wood door fr ont panels: ^ Door fronts made fr om wood should only be cleaned using a damp cham - ois leather and then dried with a soft cloth. , Do not use any cleaning agents containing ammonia or thinners.
With the aid of the following guide, minor problems can be easily corr ected with - out calling in a Miele service technician, saving you both time and money . Y ou should, however , note the following: , Repairs should only be carried out by a suitably qualified and trained per - son in accordance with local and national safety r egulations.
Prob lem P ossible cause Remedy The indicator light "In - let/Drain" lights up and flashes alternately The stopcock is closed. Open the stopcock fully . The water inlet filter is blocked. Before r ectifying the prob - lem you must: – T ur n the programme selector to the "Stop" position.
Prob lem P ossible cause Remedy The indicator light "In - let/Drain" is flashing and the programme does not continue. Before r ectifying the prob - lem you must: – T ur n the programme selector to the "Stop" position. – Switch the dishwasher off using the "On/Of f" button.
Prob lem P ossible cause Remedy The "End" and "Start" indicator lights flash si - multaneousl y at the end of a programme There may be a technical fault. – T ur n the programme selector to the "Stop" position. – Switch the dishwasher off using the "On/Of f" button.
Prob lem P ossible cause Remedy Knocking noise in the wash cabinet The spray arm is knocking against an item in the bas - ket. Interrupt the programme, rearrange items which ar e obstructing the spray arm. Rattling noise Items of crockery are in - secure in the wash cabi - net.
Prob lem P ossible cause Remedy The dishes are not clean The dishes wer e not loaded correctly . Dishes were placed inside other pieces, water could not access all surfaces. See notes in "Loading the dishwasher". The outlet of the water in - take pipe for the middle spray arm was covered.
Prob lem P ossible cause Remedy Dishes, cutlery and glasses are not dry or are flecked The rinse aid amount may be insufficient or the rinse aid reservoir empty . Increase the dosage or replenish the r eservoir , see "Before using for the first time".
Prob lem P ossible cause Remedy Glassware is dull and discoloured; film can - not be wiped off Glassware is not dishwasherproof. The sur - faces are af fected.
Prob lem P ossible cause Remedy The detergent lid cannot be closed pr operly . Clogged detergent resi - due is blocking the catch. Remove the residue. Detergent residue is left in the dispenser at the end of a programme The dispenser was still damp when detergent was added.
Cleaning the water inlet filter A filter is incorporated in the screw con - nection of the valve on the water inlet hose. The filter must be cleaned when dirty , otherwise insufficient water flows into the wash cabinet. , The plastic housing of the water connection contains an electrical component.
Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however , easy to clean. W atch out for glass or bone splinters which could cause injury .
^ Lift up the non-return valve and rinse well under running water . ^ Remove all foreign objects fr om the non-return valve. The drain pump is situated under the non-return valve (see arrow). ^ Remove all foreign objects fr om the drain pump (watch out for glass or bone splinters which are particularly difficult to detect and could cause in- jury).
Should you still have any difficulties, please contact: – Y our Miele Dealer or – The Miele Service Department (see back cover for address). ^ Please quote the model type and number of your appliance. This information is given on the data plate at the top of the door .
T o make the most of your dishwasher If you w ould like … you will need to or der … ... to wash bottles, e. g. milk or baby bottles … . a bottle holder … . to wash long-stemmed glassware … . a glasswar e insert for the upper basket … . to wash additional items of cut - lery … .
T est standard: EN 50242 Standard pr ogramme Economy for comparison tests (energy label): Note: The Universal Plus 55 ° pr ogramme for normal soiling has increased wash and drying results with shorter running times and increased energy r equirements.
Dishwashers with cutlery tra y Upper basket Cutlery tray Lower basket Comparison tests 58.
Should you ever need to move the dish - washer , e.g. when moving house, note the following: – Empty the dishwasher , – Secure any loose parts, e. g. hoses, mains cable, cutlery baskets, lower basket – T ranspor t the dishwasher in the up - right position.
Programme When to use Detergent Compartment II (W ash cycle) Intensive 75 ° for normally soiled pots, pans, dishes etc with dried on soiling; for very heavy soiling, add 20% more detergent to compart.
Programme sequence Consumption Duration Energy kWh W ater h:min Pre- wash 12 Main wash Interim rinse Final rinse Drying Cold water con - nection (15 °C) Hot water con - nection (55 °C) Litres Cold water con - nection (15 °C) Hot water con - nection (55 °C) X 75 ° XX 75 ° X 1.
Height freestanding 84,7 cm (adjustable +4.0 cm) Height built-in 81.7 cm (adjustable +5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) Width 59.8 cm Width of building in recess 60 cm Depth: 60 cm (Freestanding) 57 cm (Built-in) Depth with door open 118.
63.
M.-Nr . 05 714 400 / V Alteration rights reserved/ (G636/G638/G639 Plus) / 2902 This paper consists of cellulose which has been bleached without the use of chlorine.
An important point after buying a device Miele 05 714 400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele 05 714 400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele 05 714 400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele 05 714 400 you will learn all the available features of the product, as well as information on its operation. The information that you get Miele 05 714 400 will certainly help you make a decision on the purchase.
If you already are a holder of Miele 05 714 400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele 05 714 400.
However, one of the most important roles played by the user manual is to help in solving problems with Miele 05 714 400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele 05 714 400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
