Instruction/ maintenance manual of the product LC2000 Microsoft
Go to page of 22
Micr osoft Small Business Server 2000 Installation Guide fo r HP NetServers E60, E800, LC2000, and HP Server tc3100, and tc4100 NOT ICE: The inform ation in this document w as last update d for the HP NetServer Navigator CD-ROM ver sion M.04.05. If y ou don't hav e the M.
Tip #3. Upgrading Small Business Server 2000 from Uniprocessor HAL to Multiprocessor HAL Tip #4. Small Business Serv er 2000 Driver Signat ures Tip #5. Upgrading D5013B NIC Drivers for Small Business Server 2000 Tip #6. Installation Fails to B oot after First Reboot Tip #7.
· One or more hard drives. · Latest system BIOS update. (http://www.hp.com) · Two or more clients for t e sting purpose. (Optional) · HP Driver's diskette if installing devices that have no drive rs included in the Small Business Server 2000 CD-ROM.
Computer Name: ______________________ Admin Password: _____________________ Date Time Zone: ______________________ Workgroup or Domain Name: ______________ Registration Key: ____________________________ Installation Methods There are s everal ways of installing Small Busi ness Server 2000.
Manual Installation Creating the Driver s Diskette Before y ou be gin, use one of the followin g two methods that can be used to creat e the drivers diskette.
· If you want to start the setup by booting di rectly off the Small Business Server 2000 CD (supported for all NetServers), pro ceed to th e following section "Installing Small Business Server 2000." Creat ing Setup Diskettes If you opt for starting the Small Business Server 2000 installation from Setup Diskettes, do the following: 1.
NOTE: If the boot device driver is not included on the Small Business Server 2000 CD- ROM, for exampl e the "HP NetRA ID-4M", then do t he following steps aft er pressing F6 a) Press S to select additional hardware. b) Select Other and press Enter .
15. Note: If you see a dialog box titled "Digital Signature Not Found". Please click "Yes" to continue the installati on and read Tip #4 in the trouble shooting section of this guide . 16. Click Next at the reg ional Settings scre en.
2. Click Prop e rti es . This brings up the "System Properties" panel. 3. Click the Hardw are tab. 4. Click the Device Manag er… button. 5.
1. Click Start | Programs | Administrative Tools | Computer Managemen t . 2. If necessary click the + sign next to Storage to open this folder. 3. Double click Disk Management . 4. The "Write signa ture and Upgrade" wizard will start if you ha ve new hard drives with no signatures on them.
10. Open a command prompt window to verif y th e TC P/IP configuration. Enter the command: ipconfig /a ll You should get a display showing the conf iguration information y ou entered above. 11. Test the link by entering the following at the comm and prompt: ping computername Where com puternam e is the server name.
7. Click Next . The system will take a few minutes with the hour clock on th e display before moving to next screen. 8. Click Next at the "Net BIOS Domai n Name" dialo g box to accept d efault " Domain NetB IOS name:" 9.
Tip #1. Up grading f rom SBS 4.0 t o Small Busi ness Server 2 000 It is possible to upgrade from any edition of NT 4. 0 including Terminal Server to Small Business Server 2000. Please refe r to the readme.doc on th e Small Business Server 2000 CD and the Small Business Server 2000 Setup Guide for in formation on how to perform the upgrades.
5. Click "Display a list of known drivers for this device", and then click "Sho w all hardware of this device cl ass". 6. Click the appropr iate computer t y pe (one that matches your curr ent t ype , except for multiple CPUs), click Next , and then click Fin is h .
5. At the prompt "What do y o u want the wizard to do?", select the "Sea rch for a suitable driver for my device" radio button, and click Next . 6. Select the appropriate me dia checkbox and click nex t. 7. Select the "Install one of the othe r drivers" check box and click Nex t.
2. Networking disab led. Includes networks services and drivers. 3. Directory se rvices restore mode. Brings system up with director y servi ces disabled with the intent of recovering activ e directory. Safe mode boot is guided by the registry key hklmCurrentControlSetControl Safe Boot w ith the use of the Minimal and Network subkeys.
8. Type exit when done troubleshooting. Installing RC 1. Insert Small Business Server 2000 CD-ROM. If CD-ROM auto-start is enabled, click exit to close the applet. 2. Open a command prompt and type D:I386WINNT32 /CMDCONS and press Enter . (Where D: is the CD-ROM drive le tter.
Answer: Table 6, provid ed in the appendix of this document provides a list of Disk Arra y BIOS/Firmware versions used to test with Small Business Server 2000.
E60 Yes Yes Yes E800 Yes Yes Yes LC2000 Yes Yes Yes tc3100 Yes Yes Yes tc4100 Yes Yes Yes Table #2 List of embedded SCSI chip set for each NetServ er. (Note: See "Table #6" fo r a list of te.
* The driver is not provided b y Hewlett-Packard. Users should use the dri ver bundled with Windows NT CD-ROM. Note: Video adapters wit h 1M can be upgraded to 2M.
III (1.2- 1.4 GHz) tc4100 N/A Dual Pentium III (1.2- 1.4 GHz) 4G ATIRage XL PCI TBD Yes TBD Table #6A This table provides a list of Disk Array Adap ters tested with Sm all Business Server 2000. Adapter P/N BIOS Firmware Win 2K Support Max Boot Drive Si ze (1) NetRaid-4M D9161A V2.
tc3100 No No No No Yes Yes No tc4100 No No No No Yes Yes Yes Table #6C List of NeRAID-4M, 2M and 1M adapters supported with Small Business Server 2000.
An important point after buying a device Microsoft LC2000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Microsoft LC2000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Microsoft LC2000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Microsoft LC2000 you will learn all the available features of the product, as well as information on its operation. The information that you get Microsoft LC2000 will certainly help you make a decision on the purchase.
If you already are a holder of Microsoft LC2000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Microsoft LC2000.
However, one of the most important roles played by the user manual is to help in solving problems with Microsoft LC2000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Microsoft LC2000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
