Instruction/ maintenance manual of the product 2200RT MGE UPS Systems
Go to page of 28
www.mgeups.com Pulsar EX 2200RT / 3200R T EXB 2200/3200 RT Installation and User Manual MGE UPS SYSTEMS,INC..
SA VE THESE INSTRUCTIONS. This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Thank you for selecting an MGE UPS SYSTEMS, Inc. product to protect your electrical equipment. The Pulsar EX RT range has been designed with the utmost care.
3400753300/AE - Page 3 CAUTION: Safety of persons ◗ The UPS has its own internal power source (the battery). Consequently , the power outlets may be energized even if the UPS is disconnected from the AC-power source. ◗ Dangerous voltage levels are present within the UPS.
Page 4 - 3400753300/AE Using this document How to use this document Icon Usage Information may be found primarily by consulting: ◗ The contents, ◗ The index. In the illustrations on the following pages, the symbols below are used: LED off. LED on.
3400753300/AE - Page 5 1. Presentation 1.1 System configurations ....................................................................................................... ......... 7 Rack setup ...........................................................
Page 6 - 3400753300/AE 4. Maintenance 4.1 T roubleshooting .......................................................................................................................... 20 4.2 Replacement of the battery modules ...........................
P U L S A R w w w. m g e u p s . c o m 1 0 0 % 8 0 % 5 0 % 2 0 % t e s t % 1 2 % B Y P A S S E X 3400753300/AE - Page 7 Tower setup Rack setup 1.1 System configurations 1. Presentation w w w . m g e u p s . co m P U L S A R 3.75 inches (2U) 25.75 inches (EX 2200RT) 26.
Page 8 - 3400753300/AE 4 6 12 11 10 9 8 7 1 3 2 4 12 11 10 9 8 7 5 3 2 1 15 14 15 14 13 12 Pulsar EXB 2200/3200 RT Pulsar EX 3200RT Pulsar EX 2200RT 11 10 8 9 7 6 5 4 3 2 1 Slot for communication-card option. RS232 communication port. USB communication port.
3400753300/AE - Page 9 27 26 25 24 23 22 21 20 19 18 17 16 (*) : ◗ flashing LED + buzzer: battery fault (battery must be replaced). ◗ flashing LED + long buzzer (once per hour): theoretical end of battery life (replacement recommended).
Page 10 - 3400753300/AE 34 34 36 35 36 35 30 32 31 30 32 31 RS232 communication cable. USB communication cable. T elescopic rails for mounting in 19" bay with mounting hardware. CD-ROM with the Solution-Pac and UPS Driver software. Product documentation.
3400753300/AE - Page 11 3 3 7 Stop-Notch Snap from inside of rails 2 6 4 5 5 2 1 CAUTION: Do not lean or place objects on top of unit at any time. Hazard of dismounting and disconnection can occur with units. NOTE: (For step 5) it is possible to adjust the position of the front fixing bracket.
Page 12 - 3400753300/AE Install the two supports for the upright position using provided hardware in the package. (see item 32 on page 10). Pull out the MGE Logo and Model plates, then rotate them as shown. 2. Installation 2.3 Installation in tower position P U L S A R P U L S A R www.
3400753300/AE - Page 13 1 Slot for the communication card option. It is not necessary to shut down the UPS to install the communication card: 1. Remove the slot 1 cover secured by two screws. 2. Insert the card in the slot. 3. Secure the card with the two screws.
Page 14 - 3400753300/AE 5 4 4 7 1. Connect the input power cord 7 to the AC-power wall-receptacle. 2. Connect the protected equipment to the UPS. It is advised to connect priority loads to the outlets and/or power cord 4 and any non-priority loads to the two programmable outlets 5 (If the UPS is connected to a computer running MGE UPS SYSTEMS, Inc.
3400753300/AE - Page 15 27 26 25 18 17 16 24 20 19 21 22 23 27 26 25 18 17 16 Description of LED indicator status 20 and 21 for programmable outlets 1 and 2: ◗ OFF: the outlets are not supplied with power . ◗ Flashing: status change in progress. ◗ ON: the outlets are supplied with power .
Page 16 - 3400753300/AE 22 17 17 The UPS goes to sleep mode at the end of the battery backup time, until complete shutdown, due to tripping of the battery-protection function against deep discharge.
3400753300/AE - Page 17 "ON / OFF conditions" tab Options Once a day Once a month No test From 0% to 100% of the remaining battery backup time Disabled Default setting Every weeks 20% remain.
Page 18 - 3400753300/AE 16 Press button 16 (return to the OFF position). The connected equipment is no longer supplied with power . 3.5 UPS shutdown "Bypass" tab "Output" tab Optio.
3400753300/AE - Page 19 38 37 12 1. Check that the UPS is shut off and disconnected from the AC power source. 2. Remove the RPO connector 12 by undoing the screws 37 . 3. Connect an insulated dry contact (NC, 60 V DC, 30 V AC max., 20 mA max., cable size 0.
Indication Diagnostic Correction LED 27 flashes and UPS overload. Overload is too long or too high. ◗ Check the power drawn by the the buzzer beeps. ◗ If AC power is present and within tolerances, the equipment and disconnect any UPS goes to bypass mode (supply directly by the non-priority devices.
3400753300/AE - Page 21 Indication Signification Correction The outlets are not supplied One of the protection circuit breakers 6 for the ◗ Check that there is not a short- with power , even though outlets (on the back of the UPS) is open. circuit on the outlets.
C D P U L S A R 1 0 0% 8 0% 5 0% 2 0 % t e st % 1 2 % B Y PA SS E X B A w w w . m ge u p s. c o m P U L S A R 1 0 0% 8 0 % 50 % 2 0 % t es t % 1 2 % B Y P A S S E X Page 22 - 3400753300/AE C - Remove the left part of the front panel. D - Disconnect the connector .
3400753300/AE - Page 23 G - Remove the two battery modules and proceed with replacement. Reinstallation of the battery module s To reinstall the battery modules perform this procedure in reverse order e.
Page 24 - 3400753300/AE This product has been designed to respect the environment: It does not contain CFC's or HCFC's. UPS recycling at the end of service life: MGE UPS SYSTEMS, Inc.
Output power rating AC-input ◗ V oltage ◗ Frequency ◗ Power factor Output specification ◗ V oltage ◗ Frequency ◗ Harmonic distortion ◗ Overload capability Battery (sealed lead-acid, main.
Page 26 - 3400753300/AE Authorized voltage range for Upper and lower voltage thresholds within which the UPS can operate on the automatic transfer to bypass if fault or bypass in the event of a UPS fault or overload.
3400753300/AE - Page 27 O ON LINE mode ..................................................................9 Overload ................................................................9-18-20 P Personalization .............................................
For service call: 1 800 523-0142 Internet: www .mgeups.com T H E U N I N T E R R U P T I B L E P O W E R P R O V I D E R 3400753300-AE 1660 Scenic Avenue Costa Mesa, CA 92626, USA Main Number: 714 557-1636 MGE UPS SYSTEMS, INC.
An important point after buying a device MGE UPS Systems 2200RT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought MGE UPS Systems 2200RT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data MGE UPS Systems 2200RT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, MGE UPS Systems 2200RT you will learn all the available features of the product, as well as information on its operation. The information that you get MGE UPS Systems 2200RT will certainly help you make a decision on the purchase.
If you already are a holder of MGE UPS Systems 2200RT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime MGE UPS Systems 2200RT.
However, one of the most important roles played by the user manual is to help in solving problems with MGE UPS Systems 2200RT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device MGE UPS Systems 2200RT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
