Instruction/ maintenance manual of the product R111-18 METRObility Optical Systems
Go to page of 16
Installation & User Guide Models: R1 1 1-12 / R1 1 1-13 / R1 1 1-15 / R1 1 1-16 / R1 1 1-18 / R1 1 1-1T R ADIANCE 10M BPS S INGLE I NTERF ACE L INE C ARDS PWR LK LK AT TP AT 10BASE PWR LK AT COL 1.
This publication is protected by the copyright laws of the United States and other countries, with all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, tra.
T able of Contents Radiance 10Mbps Single Interface Line Cards Installation & User Guide Overview ............................................................................................................... 4 Installation Guide ................
4 Overview The Radiance 10Mbps single interface line cards offer transpar ent integration of fiber optic connectivity or copper-to-coaxial integration in Ethernet networks. These innovative solutions provide full signal restoration— with low bit delay—ensuring accurate data transmission and guaranteeing maximum cable length support.
Radiance 10Mbps Single Interface Line Cards 5 Installation Guide Follow the simple steps outlined in this section to install and start using your Radiance 10Mbps single interface line card. NOTE: Electr ostatic dischar ge pr ecautions should be taken when handling any line car d.
6 Installation Guide R1 1 1-12 Only On the RJ-45 to BNC line card, a jumper is used to set either internal or external termination of the BNC port. See the diagram below to locate the jumper , labeled JP1. • Connect pins 1 and 2 to enable internal 50 Ω termination.
Radiance 10Mbps Single Interface Line Cards 7 3 Set the MDI-II/MDI-X Switch (twisted-pair ports only) T o eliminate the need for crossover cables, the Radiance line cards have an MDI- II to MDI- X slide switch for each twisted-pair port.
8 Installation Guide 4 • Grasp the card by the front panel as shown. • Insert the line card into a slot on the chassis making sure that the top and bottom edges of the board are aligned with the top and bottom card guides in the chassis. Do not force the board into the chassis unnecessarily .
Radiance 10Mbps Single Interface Line Cards 9 LK AT FL PWR AT LK 10 BASE RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10/100 RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10/100 LK AT FL R X PWR FD RX .
10 User Guide User Guide This section contains information about the operating features of the Radiance 10Mbps single interface line cards. LED Indicators The Radiance 10Mbps single interface line cards provide several LEDs for the visible verification of unit status and proper functionality .
Radiance 10Mbps Single Interface Line Cards 11 Link Loss Carry Forward (LLCF) * The Radiance 10Mbps single interface line cards incorporate an LLCF function for troubleshooting a remote connection. When LLCF is enabled, the FL and TP ports do not transmit a link signal until they receive a link signal from the opposite port.
12 User Guide T echnical Specifications Data Rate Data Rate ______________________ 10Mbps half duplex; 20Mbps full duplex Bit Delay __________________________________________________ < 5 bits Environmental Power ___________________________________ 5V @ 1.
Radiance 10Mbps Single Interface Line Cards 13 Multimode F/O Interface (R1 1 1-13, R1 11-15, R1 11-18) Connector __________________________________________ SC, ST or SMA W avelength _________________________________________________ 820nm RX Input Sensitivity ______________________________ -32.
14 User Guide Product Safety , EMC and Compliance Statements This equipment complies with the following requirements: •U L • CSA • EN60950 (safety) • FCC Part 15, Class A • EN55022 Class A (.
Radiance 10Mbps Single Interface Line Cards 15 W arranty and Servicing Three-Y ear W arranty for Radiance 10Mbps Single Interface Line Cards Metrobility Optical Systems, Inc.
Product Manuals The most recent version of this manual is available online at http://www .metrobility .com/support/manuals.htm Product Registration T o register your product, go to http://www .metrobility .com/support/registration.asp 25 Manchester Street, Merrimack, NH 03054 USA tel: 1.
An important point after buying a device METRObility Optical Systems R111-18 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought METRObility Optical Systems R111-18 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data METRObility Optical Systems R111-18 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, METRObility Optical Systems R111-18 you will learn all the available features of the product, as well as information on its operation. The information that you get METRObility Optical Systems R111-18 will certainly help you make a decision on the purchase.
If you already are a holder of METRObility Optical Systems R111-18, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime METRObility Optical Systems R111-18.
However, one of the most important roles played by the user manual is to help in solving problems with METRObility Optical Systems R111-18. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device METRObility Optical Systems R111-18 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
