Instruction/ maintenance manual of the product Automobile Parts Metra Electronics
Go to page of 16
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORA TION 1-800-221-0932 axxessinterf ace.com INST ALLA TION INSTRUCTIONS FOR PART ASWCST ALK The ASWCST ALK is the newest addition to the Axxess steering wheel control solution, allowing you to add steering wheel control options to your vehicle.
T OOLS REQUIRED FOR INST ALLA TION •Cutting T ool •T ape •Crimping T ool •Connectors (I.E. butt-connectors, bell caps, ECT…) • Female Spade Connectors IGNITION TERMINALS WIRE CUTTER M3.5 M2.6 M3 M5 M4 ISO 6 2.5 1.5 *Impor tant: Please chec k steering shroud before drilling to mak e sure you hav e enough depth.
ASWCST ALK ASSEMBL Y 1. Remove and drill a 3/8 hole in the steering wheel shroud. 2. Select desired length rod and thread a 3/8 hex nut on to the shorter threaded section. 3. Run the four wires from the ASWCST ALK through the rod of choice and screw it into the ASWCST ALK 4.
Wiring Of ASWCST ALK And Interface 1. Connect the BLACK wires of the ASWCST ALK and the BLACK wire of the interface to ground. Y ou may use the same ground point that is used for the radio. 2. Connect the GREEN/ORANGE and BLACK/GREEN wires of the ASWCST ALK to the corresponding wires on the interface.
Programming the ASWCST ALK * If this is the rst time the ASWCST ALK is being installed: 1. T urn the ignition on; the led will start ashing rapidly which means the interface is looking for the ASWCST ALK and the radio. Go to step 3. OR * If the ASWCST ALK was installed before: 1.
4. The ASWCST ALK is now congured for the right side. T roubleshooting the Auto Detect Mode So you tried the auto detect feature and at the end the led did not stay on solid red, it started ashing, or the steering wheel controls did not function properly .
• Long ashes represent the wire(s) that are connected to the interface • 3rd led ash is the Green/Orange wire on the interface • 5th led ash is the Black/Green wire on the interface If .
1. V olume up 2. V olume down 3. Seek up 4. Seek down 5. Mode (source) 1. V olume up 2. V olume down 3. Seek up 4. Seek down 5. Mode (source) Remapping the ASWCST ALK Let’s say you have the ASWCST ALK programmed to your radio and you want to change the button assignment for the steering wheel controls.
NOTES: • The interface must have detected the ASWCST ALK and radio it is attached to before you can remap any buttons. • Y ou can only start the remapping of the steering wheel controls process within the rst 20 seconds of turning the ignition key on.
5. Source/Mode 6. Mute 7. Preset Up 8. Preset Down 9. Power 10. Band 1 1. Play/Enter 12. PTT (Push T o T alk) 13. On Hook 14. Off Hook 15. Fan Up 16. Fan Down 17. T emp Up 18. T emp Down * Note: Remember not all radios will have all these commands. Please refer to the radios’ owners manual for specic commands recognized by the radio.
After the 18th button is programmed or skipped the led will go out and the remapping is completed. If for any reason after remapping the steering wheel controls you want to go back to the original steering wheel control settings, follow the step in “IF the ASWCST ALK was installed before”.
programmed Kenwood. 5) Here is the chart to show how many presses of the V olume Up button is needed for which radio you are trying to program: 1st led ash is for Eclipse 2nd led ash is for Kenw.
NO TES.
NO TES.
NO TES.
REV . 8/22/1 1 1-800-221-0932 axxessinterf ace.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORA TION INST ALLA TION INSTRUCTIONS FOR PART ASWCST ALK K NO WLEDGE IS P OW ER E nhance your installation and fabrication skills by enrolling in the most re cognized and re spected mobile electronics school in our industry .
An important point after buying a device Metra Electronics Automobile Parts (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics Automobile Parts yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics Automobile Parts - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics Automobile Parts you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics Automobile Parts will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics Automobile Parts, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics Automobile Parts.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics Automobile Parts. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics Automobile Parts along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
