Instruction/ maintenance manual of the product 99-7503 Metra Electronics
Go to page of 16
INST ALLA TION INSTRUCTIONS FOR P ART 99-7503 Phillips Screwdriver I Small Flat Blade Screwdriver I Socke t Wrenc h 1-800-221-0932 www .metr aonline.com KIT FEA TURES © COPYRIGHT 2004 METRA ELECTRONI.
Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Electronic Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Manual Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Kit Assembly .
99-7503 1 Disconnect the negative batter y terminal to prevent an accidental short circuit. 1 Unscrew the shift knob counter clockwise to remove . (Figure A) 2 2003-2004 MAZD A 6 Unclip and remove the cup holder/parking brake co ver and shifter cover as one unit.
99-7503 D A SH DISA SSEMBL Y 2003-2004 MAZD A 6 Electronic Climate Control Unsnap and remove radio/climate control panel including climate con- trol vents at the top . (Figure E) Remove (4) Phillips screws securing vents to radio/climate control panel to remove .
3 Disconnect the negative batter y terminal to prevent an accidental short circuit. 1 Unscrew the shift knob counter clockwise to remove . (Figure A) 2 Remove (2) Phillips screws from the bottom of the radio/climate control panel. (Figure C) 4 Pull the climate control knobs off and r emo ve (2) Phillips scr ews from behind knobs.
Open glove box, squeeze sides together and let open fully then remove (1) 10 MM bolt from the side of the radio brack et. (Figure E) 6 INSIDE GLOVE BOX E 4 99-7503 D A SH DISA SSEMBL Y 2003-2004 MAZD A 6 Manual Climate Control Unsnap and remove radio/climate control panel including climate con- trol vents at the top .
5 Remove (4) Phillips screws securing backlight dispersion bar and knob trim bezels. (Figure I) 10 Push the bottom edges of the knob trim bezels from the front side to the back and slide both pieces out as one unit.
6 99-7503 2003-2004 MAZD A 6 Electronic Climate Control KIT ASSEMBL Y A REAR VIEW OF ELECTRON IC C LIMATE C ONTROL B D C Clip the climate control knob outer trim ring panel into the 99-7503 housing . (Figure A) Align the screw holes in the climate control and the radio housing panel then push the climate control onto the radio housing panel.
Manual Climate Control 99-7503 KIT ASSEMBL Y 2003-2004 MAZD A 6 7 A ASSEMBLED B INSTALLED C D E Put the climate control knob outer trim panel and the backlight disper- sion bar together and clip into the radio housing panel as one unit. Note: Y ou may have to push down slightly on the middle of the unit to ease in positioning it into the kit.
8 Slide the DIN cage into the Radio Housing and secure b y bending the metal locking tabs down. (Figure A) 1 Mount the ISO Brack ets to the head unit with the screws supplied with the unit. (Figure A) 1 A A B Slide the aftermarket head unit into the DIN cage until secure .
9 FEL T T APE APPLICA TION 99-7503 Apply To Rear Of Both Sides Note: Due to differences in factor y tolerances you may need to apply the provided felt tape to the edge of the 99-7503 radio housing to relieve bac klight bleed through. 1. Looking at edge of radio housing apply felt tape to inner edge (tow ard back of kit).
10 DISPLA Y CUSTOMIZ A TION 99-7503 CLOCK SET DIMMER AMB 1. Press and hold the Clock button in the factory display until “Set T ext” is display ed, then release the button.
11 FINAL WIRING and A SSEMBL Y 1 2 3 4 5 6 Locate the factor y wiring harness in the dash. Use the supplied wire harnesses and make the connection as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.
12 NOTES 99-7503.
13 NOTES 99-7503.
INST997503 1-800-221-0932 www .metr aonline.com REV . 09/09/05 © COPYRIGHT 2004 METRA ELECTRONICS CORPORA TION INST99-7503.
An important point after buying a device Metra Electronics 99-7503 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics 99-7503 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics 99-7503 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics 99-7503 you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics 99-7503 will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics 99-7503, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics 99-7503.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics 99-7503. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics 99-7503 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
