Instruction/ maintenance manual of the product BKS 450 Metabo
Go to page of 12
Model No. 1001 3305 Stock-no. 115 107 8059 Assembly/Operating Instructions Site Saw BKS 400/BKS 450.
Contents 1.0 Scope of Application 2.0 Specifications 3.0 User Responsibility 4.0 Standard Accessories 5.0 Optional Accessories 6.0 Assembly 7.0 Mitre Fence Assembly 8.0 Installation 9.0 Operation/Settings 10.0 Cutting 11.0 Saw Dust Collection (optional accessory) 12.
Note Within the U.K., this machine falls under the Woodworking Machinery Regulations 1974, under which certain operations, e.g. grooving, rebatting, tenoning and moulding are prohibited without special guards. For your own safety it is recommended to follow the instructions given in the Health and Safety at Work booklet No.
Place both support struts onto the table, set square with the slot of the table insert and bolt to the table. Use 10 each countersunk screw M6x16, hex. nut M6 Install the guard support bracket without fully tightening the screws. Use 2 each countersunk screw M6x16, hex.
Attach mitre scale to segment using 3 each tapping screw 3.9x9.5 washer 4.3 Place mitre fence segment onto carrier and screw fitting bolt through segment into glide piece. Hardware: fitting bolt SW 19x42 spring washer 12 plastic glide piece with threaded bush.
Place carriage bolt M10x30 from underneath through carrier and slot of fence segment. Install washer Ø 10.5 and ratched lever M10 female. Install 0 ° (90 ° ) setting screw into mitre fence carrier.
8.4 Switch/Motor Protection/Motor Brake The magnetic switch does not engage if not connected to power mains. It disengages in the event of a power failure (no-volt release). When the power is restored the machine has to be started again. The built-in motor protection relay switches the motor off in case it becomes too hot.
Set rip fence to required width of cut. Distance from blade is shown on the rip fence scale. Loosen scale fixing screw to adjust rip fence scale to give exact reading of width of cut. Make trial cut to verify setting. Lock rip fence in position by pushing the cam-lock lever down.
10.1 Ripping/Through Sawing 10.0 Cutting Have riving knife and blade guard in place - danger of injury. Set blade guard to thickness of work- piece. Set rip fence to desired width of cut and lock in position. D - Push mitre and work forward to feed into blade E - When cut is completed pull back both mitre fence and work 10.
10.3 Cutting Wedges A - Place work firmly into wedge cutting jig and set to desired angle. - Start machine B - Push mitre fence forward to feed work into blade.
.
U4BA_ M1.FM Achtung! Diese Seite ersetzen durch „ More of metabo- tools “ Attention! Please replace this page by „ More of metabo - tools “.
An important point after buying a device Metabo BKS 450 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metabo BKS 450 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metabo BKS 450 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metabo BKS 450 you will learn all the available features of the product, as well as information on its operation. The information that you get Metabo BKS 450 will certainly help you make a decision on the purchase.
If you already are a holder of Metabo BKS 450, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metabo BKS 450.
However, one of the most important roles played by the user manual is to help in solving problems with Metabo BKS 450. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metabo BKS 450 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
