Instruction/ maintenance manual of the product 1999 Mountaineer Mercury
Go to page of 248
Before driving Introduction 2 Instrumentation 4 Controls and features 19 Seating and safety restraints 113 Starting and driving Starting 136 Driving 140 Roadside emergencies 166 Servicing Maintenance and care 187 Capacities and specifications 228 Customer assistance 236 Reporting safety defects 248 Index 249 All rights reserved.
ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’ s Guide carefully .
km/h RPM x 1000 0 1 2 3 4 5 6 H C F E OFF 0 20 10 30 40 50 60 70 80 90 110 200 000000 ooo o 100 20 40 60 80 100 120 140 160 180 UNLEADED FUEL ONLY H H L RSM SET ACC COAST OFF ON SRS Headlamp control (pg. 20) Instrument panel dimmer switch (pg. 21) T ilt steering wheel lever (pg.
OFF REW 1 FF 2 SIDE 1-2 3 FM 1 VOL – PUSH ON AM FM BASS TREB BAL FADE AUTO SET CLK SEEK TUNE DISCS SCAN 4 DOLBY SYSTEM EJ T APE CD COMP 5 SHUFFLE 6 PUSH OD ON/OFF OFF ON R. WIPE • A/C • MAX A/C Rear window defroster control (pg. 31) Rear window/washer control (pg.
W ARNING LIGHTS AND CHIMES Check engine Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly installing and securely tightening the gas cap.
Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter . Brake system warning Momentarily illuminates when the ignition is turned to the ON position and the engine is off.
High beams Illuminates when the high beam headlamps are turned on. Anti-theft system (if equipped) Refer to SecuriLock y passive anti-theft system in the Controls and features chapter . Charging system Illuminates when the ignition is turned to the ON position and the engine is off.
Four wheel drive high (if equipped) This light momentarily illuminates when the ignition is turned to ON. Illuminates when four -wheel drive high is engaged. If the light continues to flash have the system serviced. Door ajar Illuminates when the ignition is in the ON or ST ART position and any door is open.
pressed, the brake is applied or the ignition is turned to the OFF position. Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter .
Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating.
Odometer Registers the total kilometers (miles) of the vehicle. T rip odometer Registers the kilometers (miles) of individual journeys. T o reset, depress the control. T achometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’ s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system.
Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty , there is a small amount of reserve fuel in the tank.
Selectable features English/metric display Press to toggle the message center display between metric or English units. Fuel range Press once to display the approximate kilometers (miles) left to drive before the fuel tank is empty . Press again to display the distance driven since this function was last manually reset.
Fuel economy Press to display your vehicle’ s average fuel economy in liters/100 km or (miles/gallons). Reset Press the reset control to reset the current feature being displayed. W arnings, distance driven, average fuel economy , fuel used and personalized oil reset percentage are the only features that respond to reset.
The engine oil life left has two phases. The first display will indicate the oil change status (OK, SOON, REQUIRED). The second display will indicate the percentage of oil life remaining. The display OIL TEMP SIGNAL ERROR indicates a problem with the system.
OIL LIFE RESET TO 100%. (If you have established a personalized oil reset percentage, the display will show that percentage instead of 100%.) This reset procedure should be performed only after an oil change to ensure accurate oil life indications.
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Foglamp control (if equipped) T urn on the low-beam headlamps and press the foglamp control to activate the foglamps.
Flash to pass Pull toward you to activate and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full down position to turn off.
T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
• (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode.
• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Turning the EA TC off Press OFF . Automatic operation Press AUTOMA TIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window . The EA TC system will either heat or cool to achieve the selected temperature.
T o control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window .
• Rotate the thumbwheel up for higher fan speed or down for lower fan speed. • Press the steering wheel fan speed control up for higher fan speed or down for lower fan speed. The display will show to indicate manual fan operation. T o return to automatic fan operation, press AUTOMA TIC.
• PNL • FLR-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode.
The EA TC display window will indicate REAR F AN OFF . The rear console fan will remain off until REAR F AN OFF is pressed again. Operating tips • In humid weather , select DEF before driving. This will prevent your windshield from fogging. After a few minutes, select any desired position.
Rear console climate controls (if equipped) Depending on the equipment package of your vehicle, the rear console may be equipped with rear console audio/climate controls. The instrument panel climate controls must be on in order for the rear console climate controls to work.
Select for air to flow through these vents: REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • The small LED will illuminate when the rear defroster is activated.
4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for more information. REVERSE SENSING SYSTEM (IF EQUIPPED) The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the reverse gear is selected.
The reverse sensing system detects obstacles within approximately 1.8 meters (5.9 ft.) of the rear bumper with a decreased coverage area at the outer corners of the bumper . As you move closer to the obstacle, the rate of the tone increases. When the distance to the obstacle is less than 20.
T o help avoid personal injury , please read and understand the limitations on the reverse sensing system described above. Reverse sensing is only an assist for some (generally large and fixed) objects. It is the drivers responsibility for ensuring that their path is clear when operating the vehicle.
V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there).
Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. T ape select • T o enter tape mode while in radio mode, press the T APE AMS control.
T o activate the feature, momentarily depress the T APE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection). The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape.
Press the control to activate (and deactivate) Dolby t noise reduction. The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Setting the clock T o set the hour , press and hold the CLK control and press: • to decrease hours and • to increase hours.
• to decrease minutes and • to increase minutes. AM/FM Stereo / Single CD Radio V olume/power control Press the control to turn the audio system on or off.
T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes.
• Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band.
Radio station memory preset The radio is equipped with four or six station memory preset controls. These controls can be used to select up to four or six preset AM stations and eight or twelve FM stations (four to six in FM1 and four to six in FM2). Setting memory preset stations 1.
Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. CD select • T o begin CD play (if CD[s] are loaded), press the CD control.
Setting the clock T o set the hour , press and hold the CLK control and press: • to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press: • to decrease minutes and • to increase minutes.
Premium AM/FM Stereo/Cassette/Single CD/Premium Sound V olume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control.
If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD modes.
Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer . (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the remaining discs.
Seek function for CD or CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning. • Press to seek forward to the next track of the current disc.
Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
T o deactivate autoset and return to your audio system’ s manually set memory stations, press the AUTO control again. Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the BASS control then press: • to decrease the bass output and • to increase the bass output.
• to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the F ADE control then press: • to shift the sound to the front and • to shift the sound to the rear .
Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the T APE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control rewinds the CD within the current track.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level.
T o set the minute, press and hold the CLK control and press TUNE: • to decrease minutes and • to increase minutes. If your vehicle has a separate clock module, (other than the digital radio display), the CLK button will not function in the above manner .
Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Rear seat controls (if equipped) The Personal Audio System, a feature of the optional Pre.
T o activate the Personal Audio System, press the speaker/headphone control. Press the MODE control to change audio sources (for headphone mode only). Use the SEEK, VOLUME and MEMORY controls to make adjustments to the playing media. Adjusting the volume Press the + control to increase volume.
Turning the speakers on and of f Press to turn all speakers on or off. Using headphones Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. The rear speakers will cut out once the speaker on/off control is pressed.
Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function • In radio mode, press to find the next listenable station down the frequency band.
MACH T Audio System with AM/FM Stereo/Cassette/Single CD Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off.
T urn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there).
Seek function in tape mode • Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. Seek function for CD changer (if equipped) • Press to seek to the previous track of the current disc.
Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control.
Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the BASS control then press: • to decrease bass output and • to increase bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output.
Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the F ADE control then press: • to shift sound to the front and • to shift sound to the rear .
Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the T APE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level.
T o set the minute, press the clock/RDS control until SELECT MIN is displayed and press: • to decrease minutes and • to increase minutes. Radio Data System (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations.
RDS traffic announcement • Press the RDS control until TRAFFIC is displayed. • Use the SELECT control to select ON or OFF . W ith the feature ON, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data).
• Use the SEL control to select the program type. W ith the feature on, use the SEEK or AUTOSET or SCAN control to find the desired program type from the following selections: • Classic • Countr.
Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Rear seat controls (if equipped) The Personal Audio System, a feature of the optional Pre.
Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to T urning speakers on and off.
The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers. Press the control again to deactivate the headphones. Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped).
• In CD mode (if equipped), use the SEEK function to access the next or previous selection. CD changer (if equipped) The CD changer is located in one of the following locations: • in the trunk • in the center console • under the driver’ s seat 1.
If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder .
The CD magazine may be inserted or ejected with the radio power off. ONL Y use the magazine supplied with the CD changer , other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty .
Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation. Cassette and cassette player care • Use only cassettes that are 90 minutes long or less.
• Station overload. W eak signals are sometimes captured by stronger signals when you pass a broadcast tower . A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed.
SPEED CONTROL T o turn speed control on • Press ON. V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on.
T o set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Y ou can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. T o set a lower set speed • Press and hold CST/COAST . Release the control when the desired speed is reached or • Press and release CST/COAST .
Pressing OFF will erase the previously programmed set speed. T o return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the SET ACC/SET ACCEL or RES/RSM/RESUME controls are pressed.
TIL T STEERING WHEEL Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Push the control on the end of the stalk to activate washer . Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use.
Radio control features • Press BAND/MODE to select AM, FM1, FM2, T APE or CD (if equipped). In Radio mode: • Press MEM/NEXT to select a preset station from memory . In T ape mode: • Press MEM/NEXT to listen to the next selection on the tape. In CD mode: • Press MEM/NEXT to listen to the next track on the disc.
Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the storage clip from the door .
• Press the GARAGE control to activate the transmitter . Moon roof (if equipped) Y ou can move the moon roof back to open the glass panel or tilt up to ventilate the vehicle. T o open the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature.
Do not let children play with the moon roof. They may seriously hurt themselves. Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the MODE control on the overhead console.
Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Press and hold the MODE control until V AR appears in the display , then release. The display should show the current zone number . 3. Press the MODE control until the desired zone number appears.
Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: • Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release.
Programming 1. Prepare for programming the HomeLink t Universal T ransceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds.
Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLink t Universal T ransceiver . T o program your hand-held transmitters: • continue to hold the button on the HomeLink t Universal T ransceiver .
After completing the “Programming” functions, follow these steps to train a garage door opener with the rolling code feature: 1. Locate the training button on the garage door motor head unit. Refer to the garage door opener manual or call 1–800–355–3515 or on the Internet at HomeLink.
Reprogramming a single HomeLink T button T o program a device to HomeLink t using a HomeLink t button previously trained, follow these steps: 1. Press and hold the desired HomeLink t button.
T o play a message: 1. Press and release the PLA Y button to play the message. 2. Press and hold the PLA Y button to hear all the messages in consecutive order starting with the most recent. 3. If the PLA Y button is pressed while a message is being listened to, T ravelNote will skip to the beginning of the next message.
Setting autolamp 1. Make sure the headlamp control is in the OFF position. Leaving the headlamp control on will override the autolamp. 2. T urn the ignition to the ON position or start the vehicle.
POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. One touch down • Press AUTO completely down and release quickly .
Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the left side of the control. Press the right side to restore the window controls. POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors.
POWER SIDE VIEW MIRRORS T o adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror . 2. Move the control in the direction you wish to tilt the mirror .
• ashcup • compact disc changer (if equipped) • removable utility bag (if equipped) Use only soft cups in the cupholder . Hard objects can injure you in a collision. Auxiliary power point The power point is an additional power source for electrical accessories.
CENTER ARMREST/REAR CUPHOLDER Do not attempt to raise the console armrest when the rear cupholder is in use. If you find resistance when raising the armrest, make sure the cupholder is fully closed or else damage may occur to the armrest. POSITIVE RETENTION FLOOR MA T T o install floor mats: 1.
The liftgate door and window should be closed before driving your vehicle. If not, possible damage may occur to the liftgate door lift cylinders and attaching hardware. Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle.
1. Remove the shade from the vehicle and extend it with the smooth grain facing you. 2. W rap the vinyl around the roller tube twice. T uck the edges of the vinyl inside the end cap with each wrap. 3. Fold the edges of the vinyl towards the center , making sure that the edges clear the end cap slots.
Unlocking the doors Press this control to unlock the driver’ s door . The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. T o confirm all doors are closed and locked, press the control a second time within five seconds.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Memory seat feature (if equipped) The remote entry system can also control the memory seat feature.
The memory feature will continue to work from the door control even when deactivated at the remote entry module. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. T ypical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Replacing lost transmitters T ake all your vehicle’ s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the followin.
The autolock feature repeats when: • any door is opened and then closed • the brake pedal is released Deactivating autolock Before following the activation or deactivation procedures, make sure that the ignition is OFF and all vehicle doors and liftgate window are closed.
If autolock/relock has been changed, the horn will chirp to confirm procedure is complete. Keyless entry system (if equipped) W ith the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key • activate/deactivate the autolock feature See also Remote entry system in this chapter for more information.
If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds of step 1. 3. Press the 7/8 and 9/0 controls at the same time within five seconds of step two.
SECURILOCK Y PASSIVE ANTI-THEFT SYSTEM The SecuriLock y passive anti-theft system provides an advanced level of vehicle theft protection. Y our vehicle’ s engine can only be started with the two special SecuriLock y electronically coded keys provided with your vehicle.
Theft indicator The theft indicator on the instrument cluster will operate as follows: • When the ignition is OFF , the theft indicator will flash briefly every 2 seconds to indicate the SecuriLock y system is protecting your vehicle. • When the ignition is turned to RUN or ST ART , the theft indicator will light for 3 seconds and then go out.
Procedure to program spare SecuriLock Y keys to your vehicle New SecuriLock y keys must have the correct mechanical key cut for your vehicle. Conventional (non-SecuriLock y ) keys cannot be programmed to your vehicle.
SEA TING Using the manual lumbar support T urn the lumbar support control toward the front of vehicle to increase firmness. T urn the lumbar support control toward the rear of vehicle to increase softness. Adjusting the front power seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving.
Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
REAR SEATS Folding rear seats (if equipped) If your vehicle is equipped with a built-in child seat, the seatback cannot be folded down unless the built-in child seat is fully stowed. 1. Press the lower release control downward to unlatch the seatback.
T o return the seat to the upright position: • Press downward on the upper corner of the seatback and hold. • Pull the release handle upward to unlatch the seat. • Rotate the seatback upward until the seatback latches in the upright position. The seatback will click when it is locked into position.
All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
2. T o unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
• This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner . This feature is designed to help reduce the belt force acting on the occupant’ s chest.
Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost.
Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, wears or cuts, replacing if necessary .
Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Do not attempt to service, repair , or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer . Children and air bags For additional important safety information, read all information on safety restraints in this guide.
near -frontal collisions, not rollover , side-impact, or rear -impacts. The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
• and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.
All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided. How does the side air bag system work? The side air bag system consists of.
near -frontal collisions, unless the collision causes sufficient lateral deceleration. Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again.
SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air Bag Supplemental Restraint System (SRS) in this chapter for special instructions about using air bags.
Do not leave children, unreliable adults, or pets unattended in your vehicle. T o improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch.
Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat.
T ether anchorage hardware A tethered seat can be installed in the front seat. Put the tether strap over the seatback and attach it to an anchor bracket. An anchor bracket can be installed on the rear edge of the front seat cushion. The provision (attaching hole) is provided in the rear edge of the front passenger seat cushion frame.
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
• Make sure the parking brake is set. • Make sure the gearshift is in P (Park). 3. T urn the key to 4 (ON) without turning the key to 5 (ST ART). Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced.
ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try , turn the key to OFF , wait ten seconds and try again.
Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately .
BRAKES Y our service brakes are self-adjusting. Refer to the maintenance guide and or service guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
The air suspension shut-off switch is located in the cargo area behind the left rear quarter trim panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver .
Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whenever you leave your vehicle.
R (Reverse) W ith the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) W ith the gearshift in N (Neutral), the vehicle can be started and is free to roll.
Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired.
Always set the parking brake fully and make sure the gearshift is securely latched in P (Park). Never leave your vehicle unattended while it is running. R (Reverse) W ith the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse).
Drive – Not shown on the display . Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position. The TCIL will illuminate on the instrument cluster . T ransmission operates in gears one through four .
Forced Downshifts T o gain acceleration in (Overdrive) or Drive (O/D OFF) when passing another vehicle, push the accelerator to the floor . The transmission will downshift to the appropriate gear: fourth, third, second or first gear .
Positions of the Control-T rac system The Control-T rac system functions in three modes: • The 4WD AUTO mode provides four -wheel drive with full power delivered to the rear axle, and to the front axle as required for increased traction.
If your vehicle is equipped with 4WD or A WD, a spare tire of a different size than the road tires should never be used. Such a tire could result in damage to driveline components and make the vehicle difficult to control.
Shifting from 4WD LOW to 4WD AUTO or 4WD HIGH 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral). 4. Move the 4WD control to the 4WD AUTO or 4WD HIGH position.
Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
When speed control is on and you are driving uphill, your vehicle speed may drop considerably , especially if you are carrying a heavy load. If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically . Resume speed with accelerator pedal.
Driving off-road with A WD Y our vehicle is specially equipped for driving on sand, snow , mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain.
Once through water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. After driving through mud, clean off residue stuck to rotating driveshafts, halfshafts and tires.
Driving on snow and ice An A WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. A void sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop.
• GVWR (Gross V ehicle W eight Rating) : Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’ s door pillar . • GA WR (Gross Axle W eight Rating) : Carrying capacity for each axle system.
The Certification Label, found on the inside pillar of the driver’ s door , lists several important vehicle weight rating limitations. Before adding any additional equipment, refer to these limitations.
Once through the water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal.
T railer towing table (4x2) GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR-kg (lbs.) T railer W eight Range-kg (lbs.) 0-Maximum Maximum frontal area of trailer -m 2 (ft 2 ) 4.0L SOHC 3.55 4 082 (9 000) 0-2 041 (0-4 500) 4.
Preparing to tow Use the proper equipment for towing a trailer , and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle bumper .
Never connect any trailer lighting to the vehicle’ s taillamp circuits, because it may damage the electrical system resulting in fire. Contact your local Ford dealership for assistance in proper trailer tow wiring installation. Additional electrical equipment may be required.
• After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. • When stopped in traffic for long periods of time in hot weather , place the gearshift in P (Park) and increase idle speed.
T o adjust cross-bar position: 1. Slide the locking switches at each end of the crossbar toward the rear of the vehicle until UNLOCKED appears. 2. Slide cross-bar to the desired location. 3. Lock the cross-bar into position by pushing the locking switches on each end of the crossbar toward the front of the vehicle.
HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously .
The fuel pump shut-off switch is located in the passenger’ s foot well, behind the kick panel. FUSES AND RELA YS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver’ s side door . Pull the panel cover outward to access the fuses. T o remove a fuse use the fuse puller tool provided on the fuse panel cover .
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Description 1 7.5A Power Mirror Switch, Power Antenna 2 7.5A Blower Motor Relay , Air Bag Diagnostic Monitor 3 7.5A Left Stop/T urn T railer T ow Connector 4 10A Left Headlamp 5 10A Data Link Connector (DLC) 6 7.
Fuse/Relay Location Fuse Amp Rating Description 21 15A Flasher (Hazard) 22 20A Auxiliary Power Socket 23 — Not Used 24 7.5A Clutch Pedal Position (CPP) Switch, Starter Interrupt Relay , Anti-Theft 25 7.
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Description 1 60A** I/P Fuse Panel 2 40A** Blower Motor Relay 3 50A** 4 Wheel Anti-Lock Brake System (4W ABS) Module 4 .
Fuse/Relay Location Fuse Amp Rating Description 3 30A* Heated Backlight 4 15A* Fog Lamps and Daytime Running Lamps 5 — Not Used 6 10A* Powertrain Control Module 7 30A* 4 Wheel Anti-Lock System (4W A.
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Y our vehicle is equipped with a spare tire that must be used for emergencies only .
Stowing the spare 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel under the vehicle and install the retainer through the wheel center . 3. T urn the jack handle clockwise until the tire is raised to its original position underneath the vehicle.
When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park). 3. Block the diagonally opposite wheel. 4. Use the tip of the lug wrench to remove any wheel trim.
6. T urn OFF the air suspension switch (if equipped). Refer to Air suspension system in the Driving chapter . 7. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point.
JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor .
5. Be sure that the cables are clear of fan blades, belts and other moving parts of both engines. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3.
• 4.0L SOHC + – + – + – + – Roadside emergencies 187.
2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery .
4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
If the vehicle is towed by other means or incorrectly , vehicle damage may occur . Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a T -hook or slingbelt towing procedure. A towing manual is available from Ford Motor Company for all authorized tow truck operators.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service.
Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the steering column on the instrument panel.
2. Go to the front of the vehicle and release the auxiliary latch that is located in the center between the hood and the grill. 3. Lift the hood until the lift cylinders hold it open. IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1.
5.0L V8 engine 1. Engine coolant reservoir 2. W indshield washer fluid reservoir 3. Engine oil filler cap 4. Automatic transmission fluid dipstick 5. Brake fluid reservoir 6.
4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 4.0L V6 engine • 5.0L V8 engine 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the ADD and FULL marks (4.
• If the oil level is below the ADD mark (4.0L engine) or MIN mark (5.0L engine), add enough oil to raise the level within the ADD-FULL range (4.0L engine) or MIN-MAX range (5.0L engine). • Oil levels above the letter F in FULL (4.0L engine) or the MAX mark (5.
Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty . Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide.
Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry . This may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel.
ENGINE COOLANT Check the level of the engine coolant in the reservoir . Refer to the Scheduled Maintenance Guide for service interval schedules. Be sure to read and understand Precautions when servicing your vehicle in this chapter .
Check the coolant level in the coolant reservoir the next few times you drive the vehicle. If necessary , add enough of a 50/50 mixture of coolant and water to bring the liquid level to the fill line on the reservoir . Never remove the coolant reservoir cap while the engine is running or hot.
Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes.
• 4.0L SOHC V6 engine • 5.0L V8 engine 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times.
T RANSMISSION FLUID Checking automatic transmission fluid Refer to your Scheduled Maintenance Guide for scheduled intervals for fluid checks and changes. Y our transmission does not consume fluid. However , the fluid level should be checked if the transmission is not working properly , i.
The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]). The transmission fluid should be in this range if at room temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure.
Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications.
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective.
INFORMA TION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their T ire Quality Grade (described below) molded into the tire’ s sidewall. These T ire Quality Grades are determined by standards that the United States Department of T ransportation has set.
T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
• Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial, bias-belted, or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal.
Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over .
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin.
Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas.
Running out of fuel A void running out fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • Y ou may need to crank the engine several times before the system starts to pump fuel from the tank to the engine.
If you do not use the proper fuel filler cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. Fuel Filter Y our vehicle is equipped with a fuel filter that is mounted on the underbody . For fuel filter replacement, see your dealer or a qualified service technician.
Filling the tank For consistent results: • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow three automatic click-offs when filling. • Always use the recommended octane rating of a known quality gasoline, preferably a national brand.
Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop.
Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 2 km/h [1 mpg] is lost for every 180 kg [400 lb] of weight carried).
EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use only unleaded fuel.
Do not make any unauthorized changes to your vehicle or engine. By law , vehicle owners and anyone who manufactures, repairs, items, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
• T urn signals • License plate lamp • T ail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance.
3. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) about 1/8 turn to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb. 4. Remove the old bulb from the lamp assembly by gently pulling it straight back out of the lamp assembly .
1. Rotate bulb socket counterclockwise about 1 ⁄ 4 turn and remove from lamp assembly . 2. Carefully pull bulb straight out of socket and push in the new bulb. 3. Install bulb socket in lamp assembly by turning clockwise. 4. Align the parking lamp assembly and push to snap in place.
License plate lamp bulbs T o change the license plate bulbs: 1. Remove two screws and the license plate lamp assembly from the liftgate. 2. Remove bulb socket from lamp assembly by turning counterclockwise. 3. Pull the bulb out from socket and push in the new bulb.
AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: • Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. • The headlamps do not seem to provide enough light for clear night vision.
W axing your vehicle W ax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use cleaning fluid or alcohol with a clean cloth to remove any bugs and tar before waxing vehicle.
• 5.0L • 4.0L SOHC • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wheels W ash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents.
Underbody Flush the complete underside of vehicle frequently . Keep body drain holes unplugged. Inspect for road damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary . Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.
Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. A void cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.
Woodtone trim W ipe stains with a soft cloth and a multi-purpose cleaning solution. Inside windows Use glass cleaner for the inside windows if they become fogged. Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergent and water .
MOTORCRAFT PART NUMBERS Component 4.0L SOHC V6 engine 5.0L V8 engine Air filter F A-1658 F A-1658 Fuel filter FG-986B FG-986B Battery (standard) BXT -65-650 BXT -65-650 Battery (optional) BXT -65-750 .
Fluid Ford Part Name Application Capacity T ransmission fluid Motorcraft MERCON t V AT F 4R70W Automatic with 5.0L V8 engine (A WD) 13.1L (13.9 quarts) 5R55E Automatic with 4.0L SOHC V6 engine (4x2) 9.5L (10.0 quarts) 5R55E Automatic with 4.0L SOHC V6 engine (4x4) 9.
1 If your engine coolant is green in color , use Ford Premium Cooling System Fluid. If your coolant is orange in color , use Ford Extended Life Engine Coolant. Refer to Adding engine coolant, in the Maintenance and Care chapter . 2 Fill to 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fill hole.
Item Ford part name or equivalent Ford part number Ford specification Driveshaft, slip spline, universal joints Premium Long Life Grease XG-1-C or K ESA-M1C75-B Engine coolant 1 Ford Premium Engine Co.
Item Ford part name or equivalent Ford part number Ford specification W indshield washer fluid Ultra-Clear W indshield W asher Concentrate C9AZ-19550-AC ESR-M17P5-A 1 If your engine coolant is green in color , use Ford Premium Cooling System Fluid. If your coolant is orange in color , use Ford Extended Life Engine Coolant.
VEHICLE DIMENSIONS V ehicle dimensions mm (in) (1) Overall length 4 788 (188.5) (2) Overall width 1 783 (70.2) (3) Overall height 1 725 (67.9) (4) Wheelbase 2 835 (111.
IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
V ehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. For your protection, you will also find the vehicle iden.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
Air bag supplemental restraint system ........................................ 125 and child safety seats ............ 127 description .......................126,129 disposal .................................... 131 indicator light ..................129,131 passenger air bag .
Exhaust fumes .......................... 142 Floor mats ................................. 103 Four -Wheel Drive vehicles ..............................9,10,152 control trac ............................. 152 description ................153,154,155 driving off road .
economy button ........................ 17 english/metric button ............... 16 reset button .............................. 17 system check button ........... 17,18 Mirrors automatic dimming rearview mirror ........................................
Universal transmitter (see garage door opener) ....92,93, 94,95,96 V ehicle dimensions ...................238 V ehicle Identification Number (VIN) .......................................... 240 V ehicle loading .......................... 160 V entilating your vehicle .
246.
247.
Item Information Recommended fuel Unleaded fuel only - 87 octane Fuel tank capacity 78.7L (20.8 gallons) Engine oil capacity (includes filter change) 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. T ire size and pressure See Safety Compliance Certification Label on inside of driver door .
An important point after buying a device Mercury 1999 Mountaineer (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Mercury 1999 Mountaineer yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Mercury 1999 Mountaineer - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Mercury 1999 Mountaineer you will learn all the available features of the product, as well as information on its operation. The information that you get Mercury 1999 Mountaineer will certainly help you make a decision on the purchase.
If you already are a holder of Mercury 1999 Mountaineer, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Mercury 1999 Mountaineer.
However, one of the most important roles played by the user manual is to help in solving problems with Mercury 1999 Mountaineer. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Mercury 1999 Mountaineer along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
