Instruction/ maintenance manual of the product HURRICANE 125 RB McCulloch
Go to page of 88
Instruction manual Please read these instructions care- ful ly and make sure you un der stand them before using this ma chine. Anleitungshandbuch Bitte lesen Sie diese Anleitungen sorg- fältig durch und vergewissern Sie sich, daß Sie diese verstehen, bevor Sie die Maschine in Betrieb nehmen.
2 1 2 3 4 5 6 7 8 3 18 37 45 48 60 82 85 Safety rules. Reglas de seguridad. Sicherheitsvorschriften. Norme antinfortunistiche. Règles de sécurité. V eiligheidsregels. Assembly . Montaje. Zusammenbau. Montaggio. Montage. Montering. F unctional description.
3 I. TRAINING • Read the instructions carefully . Be familiar with the con- trols and the proper use of the equipment. • Never allow children or people unfamiliar with the in- s truc tions to use the lawnmower . Local regulations may restrict the age of the operator .
4 • Stop the engine and disengage drive to attachment - before refueling; - before removing the grass catcher; - before making height adjustment unless ad just ment can be made from the op er a tor’s position.
5 • Bei Maschinen mit mehreren Mähmessern ist V orsicht geboten, da beim Drehen eines Mähmessers die anderen Mähmesser sich womöglich mit drehen. III. BETRIEB • Maschine nicht in einem geschlossenen Bereich betreiben, in dem die gefährlichen Kohlenmoxydgase sich sammeln können.
6 • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstel- len und das (die) Zündkerzenkabel abziehen bzw . den Zündschlüssel abziehen: - vor dem Entfernen von V erstopfungen aus dem Mähwerk oder dem Auswurf; - vor dem Prüfen, Reinigen oder Reparieren des Rasenmähers; - nachdem auf ein Fremdkörper gestoßen wurde.
7 • Remplacer les pots d’échappement défectueux. • Avant d’utiliser un tracteur de pelouse, toujours vérifier que les lames, les boulons de lame et le carter de coupe ne sont pas usés ou endommagés. T oujours remplacer les lames et les boulons simultanément de façon à éviter tout probléme d’équilibrage.
8 • Débrayer les lames, arrêter le moteur , et débrancher le (s) fil (s) de (s) bougie (s) d’allumage ou retirer la clef de contact : - avant de retirer l’insert broyeur ou avant de retirer la goulotte d’éjection pour la nettoyer .
9 1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORT ANTE: EST A MAQUINA CORT ADORA ES CAP AZ DE AMPUT AR L AS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERV AN L AS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRA VES O L A MUERTE.
10 • Desenganche la transmisión a los accesorios, pare el mo- tor , y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del conducto; - antes de inspeccionar , limpiar o trabajar sobre la segadora; - después de golpear un objeto extraño.
11 I. ADDESTRAMENTO ALL ’USO • Studiare attentamente le istruzioni. Acquisire dimesti- chezza con i comandi e conoscere a fondo l’uso corretto dell’equipaggiamento. • Non consentire mai l’uso dei trattorini tosaerba ai bam- bini né agli adulti che non abbiano dimestichezza con le istruzioni sull’uso.
12 • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele oppure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e .
13 I. TRAINING • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de in- structies, de maaimachine niet gebruiken. Het is mogelijk dat plaatselijke voorschriften een beperking stellen aan de leeftijd van de bestuurder .
14 • Schakel de aandrijving naar de hulpstukken uit, stop de motor en maak de bougiekabel(s) los of verwijder het contactsleuteltje, - voordat u opgehoopt materiaal weghaalt of een ver- stopte afvoer leeg maakt; - voordat u de maaimachine controleert, schoonmaakt of eraan werkt; - nadat u een ongewenst voorwerp heeft geraakt.
15 BATTERY BATTERIE BATTERIE BATERÍA BATTERIA ACCU CAUTION VORSICHT DANGER PRECAUCIÓN ATTENZIONE OPGELET BEWARE OF THROWN OBJECTS VORSICHT, HOCHGESCHLEUDERT GEGENSTÄNDE ATTENTION AUX PROJECTILES CU.
16 These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut.
17 GEF AHR AUGEN SCHÜTZEN EXPL OSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLET - ZUNGEN VERURSAC- HEN. GEVAAR OGEN BESCHERMEN EXPL OSIEVE GASSEN K UNNEN BLINDHEID OF LETSEL VERO- ORZAKEN. PELIGRO PROTEJE SUS OJOS GASES EXPL OSIVOS PUEDEN CAUSAR CE- GUE-DAD O LESIONES.
18 Ajuste del volante • Monte los components del volante en la secuencia in- dicada. • Asegúrese de que las ruedas delanteras están enderezadas y de que la barra del volante es transversal al tractor . Montaggio del volante • Montare i vari componnti nell'ordine indicato.
19 2 1 02466 02701 2 Seat Remove the hardware securing seat to the cardboard pack ing and set the hardware aside for assembly of seat to tractor . Pivot seat upward and remove from cardboard packing. Remove the cardboard packing and discard. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan (1).
20 2 NOTE! Check that the flex is correctly con nect ed to the safe ty switch (3) on the seat hold er . HINWEIS! Prüfen, daß das Kabel richtig an dem Sicherheitsschalter (3) auf dem Halter des Sitzes angeschlossen ist.
21 2 Install battery NOTE: If battery is put into service after month and year indicated on label, charge battery for minimum of one hour at 6-10 amps. WARNING: Before installing battery remove metal brace- lets, wrist watch bands, rings, etc. from your person.
22 2 WARNING: P ositive terminal must be con nect ed first to prevent sparks from ac ci den tal grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth ca ble to -. Screw tight the cables. Grease the battery poles with vaseline to prevent corrosion.
23 2 TO ADJUST GAUGE WHEELS (if equipped) Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain con di tions.
24 T o install bagger com po nents to tractor 1. Dis charge Chute 2. 3/8 Nut 3. Flat Washer 02330 3 1 2 1. 3/8 Lock nut 2. Flat Wash er 3. Support T ube 1. Support Bracket 2. Clevis Pin 10 x 17mm 3. 3/8 Lock Nut 4. 3/8 x 63,5mm Hex Bolt 5. 10,3mm (13/32") flat washer 6.
25 T o Assemble Bagger • Unfold bag by pivoting front bagger tube all the way forward and pressing the bottom vinyl binding onto the tube. • Inside the bag, install spreader bars and retainer springs onto pins on both sides of bag as shown. • Press the vinyl bindings onto the sides of front bagger tube.
26 Installation der Aufhängung der Grasfangbox des T raktors 1. Kontermutter 2. Flache Unterlegscheibe 3. Halterungder Grasfangbox 1. Strebe 2 . Fixierfeder 10x17mm 3. Kontermutter 3/8 4 . Sechskantbolzen 3/8 x 63,5mm 5. Flache Unterlegscheibe 10,3mm (13/32) 6.
27 1. V orderer Rahmen der Grasfangbox 2. Vinylverkleidung 1. Ausgleichende Oberfläche 2. Höhenjustierung 3. Seitenjustierung 4. Baggerklinke 3. Spreizstäbe 4.
28 Assemblage des composants du collecteur 1. Goulotte d'éjection 2. Ecrou 3/8 3. Rondelle plate 1. Ecrou frein diam. 3.8 2. Rondelle plate 3. Châssis porteur 1. Bras support supérieur 2 . Cheville de fixation 10x17mm 3. Ecrou frein 3/8 4. Vis H 3/8 x 63,5 5.
29 Pour assembler le collecteur • Déplier le sac en faisant basculer complètement vers l’avant le tube antérieur de l’ensacheuse et en poussant la bordure inférieure en vinyle sur le tube. • Dans le sac, placer les entretoises et les ressorts de retenue sur les goupilles des deux côtés du sac, de la façon illustrée.
30 P ara montar los componentes del contenedor para costales al tractor 1. Descarga de adaptarse 2. T uercas de 3/8 3. Arandelas planas 1. Contratuercas de 3/8 2. Arandelas planas de 13/32 3. T ubo de soporte 1. Consola portadora 2. Resorte fijador 10x17mm 3.
31 P ara montar el contenedor • Desplegar la bolsa pivoteando el tubo frontal del saco completamente hacia adelante y presionado la atadura de vinilo del fondo hacia el tubo. • En el interior de la bolsa, instalar las barras extendedoras y los resortes de retención en las clavijas en ambos lados de la bolsa como mostrado.
32 Per montare i componenti del cesto di raccolta 1. Convogliatore di scarico 2. Dadi 3/8 3. Rondella Piatta 1. Dadi 2. Rondella Piatta 3. T elaio di supporto 1. Staffa di supporto 2. Perno di fissaggio 10x17mm 3. Dadi 3/8 4. Bullone a testa esagonale (3/8 x 63,5mm) 5.
33 Per montare il cesto di raccolta: • Svolgere il sacchetto ruotando completamente in avanti il tubo anteriore dell’insaccatrice e premendo la parte inferiore in vinile sul tubo. • All’interno del sacchetto, installare le barre distanziatrici e le molle di tenuta sui perni di entrambi i lati del sacchetto, come mostrato in figura.
34 Hetmonteren van componenten van de grascontainer op de trekker 1. Afvoertrechter 2. 3/8 borgmoer 3. Vlakke sluitring 1. Borgmoer 3/8 2. Vlakke sluitring 3. Steun 1. Stennijzer 2. V orkbout 10x17mm 3. 3/8 borgmoer 4. 3/8 Zeskantbout 5. Vlakke sluitring 10,3 mm (13.
35 De grascontainer monteren • V ouw de zak open door de voorste zakkenvulbuis helemaal naar voren te draaien en de onderste band van vinyl op de buis te drukken. • Installeer in de zak de spreiders en de borgveren op de pinnen aan de beide zijden van de zak, zoals op de afbeelding.
36 A A 1 3 4 2 1. Handle 2. Retainer Spring 3. Pin 4. Plug 1. Handgriff 2. Fixierfeder 3. Stift 4. Stöpsel 1. Poignée de l'insert 2. Epingle 3. Axe de fixation 4. Tête de l'insert 1. Impugnatura 2. Coppiglia 3. Perno 4. Kit Mulch ing 1. Hendel 2.
37 3. Functional description. 3. Funktionsbeschr eibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies Positioning of controls 1. Light switch (if equipped) 2. Throttle control 3. Brake and clutch pedal 4.
38 Emplacement des commandes 1. Interrupteur des phares (si équipé ) 2. Commande de gaz 3. Pédale de frein et d'embrayage 4. Levier de changement de vitesses 5. Embrayage/débrayage du groupe de coupe 6. Abaissement et relevage du plate au de coupe.
39 3 01355 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = F ull speed = Idling speed 2. Gashebel Mit dem Gashebel wird die Drehzahl des Motors und damit die Drehgeschwindigkeit des Mähaggregats geregelt.
40 3 0 1358 3. Brake and clutch pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Brems- und Kupplungspedal Beim V orwärtsdrücken des Pedals wird das F ahrzeug abge- bremst. Gleichzeitig wird der Motor ausgekuppelt und das F ahrzeug rollt aus.
41 3 4. Gear shift lever The gear box has positions forward, neutral and re verse. Gear changing can take place from neutral to top gear with- out stopping in each gear position. Disengage the motor at each gear position! Start can take place irrespective of the gear lever position.
42 3 6. Quick lifting/lowering of the cutting unit Pull the lever backwards to quickly lift the cutting unit when passing over irregularities in the lawn, etc. During trans por - ta tion the cutting unit shall be in the highest position. Pull the lever back until it locks.
43 3 OFF ROS ON ROS ON ON ST ART 7. Cerradura de encendido La llave de encendido puede hallarse en tres posiciones diferentes: OFF Corriente eléctrica cortada ROS ON Sistema de F uncionamiento Atrás.
44 8. F rein de stationnement Pour enclencher le frein de stationnement : 1. Enfoncer à fond la pédale d'embrayage/frein. 2. Relever vers le haut le levier du frein de stationnement et le maintenir dans cette po si tion. 3. Relâcher la pédale d'embrayage/frein.
45 4. Befor e star ting. 4. Maßnahmen vor dem Anlassen. 4. A vant de démarrer . 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatr egelen vóór het star ten. Filling up The en gine should be run of pure (not oil mixed) un lead ed petrol. Do not fill beyond the lower edge of the filling hole.
46 The oil level should lie between the two markings on the oil stick. If more oil is needed add SAE 30 oil to the “FULL ” marking. SAE 5W -30 oil should be used during the winter (below freezing point). Der Ölstand soll zwischen den beiden Marken auf dem Meßstab liegen.
47 4 01362 Tire air pressure Check the tire pressure regularly . The pres sure in the front tires should be 1 bar (14 PSI) and 0.8 bar (12 PSI) in the back tires. Reifendruck Den Luftdruck in den Reifen regelmäßig prüfen. Der Druck in den V orderreifen soll 1 bar betragen, in den Hinterreifen 0,8 bar .
48 5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. 01363 Démarrage du moteur S'assurer préalablement que le carter de coupe est en posi- tion de transport (c'est .
49 Amener la clé de contact sur la position "Démarrage" ("ST ART"). REMARQUE! Ne pas laisser tourner le démarreur plus de 5 secondes à chaque fois. Si le moteur ne démarre pas immédiatement, attendre une dizaine de secondes avant d'effectuer une nouvelle tentative.
50 5 NOT A! La máquina tiene un interruptor de seguridad que corta la corriente al motor si el con duc tor sale del asiento con el motor en marcha y con la palanca de acoplamiento/ desacoplamiento en la posición de acoplamiento.
51 5 Reverse Operation System (ROS) Y our tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.
52 5 Sistema per operazioni in retromarcia (ROS) Il V ostro trattore possiede un Sistema per operazioni in re- tromarcia (ROS). Qualsiasi tentativo da parte dell’operatore di guidare nella direzione.
53 5 Cutting tips • Clear the lawn from stones and other objects which can be thrown away by the blades. • Localize and mark stones and other fixed objects to avoid collision. • Begin with a high cutting height and reduce until the required cutting result is obtained.
54 5 Consigli per il taglio dell’erba • Pulire il prato da pietre e altri corpi estranei. • Individuare ostacoli fissi. • Cominciare con un’altezza di taglio elevata e scendere progressivamente.
55 5 T o Dump Bagger Y our tractor is equipped with a Dump Bag Alarm. T o turn off the alarm disengage the attachment clutch switch. • Position tractor in location you wish to dump bagger . • Place motion control lever in Neutral position and set parking brake.
56 5 T o convert mower (Converting to mulching or rear discharging will re quire the purchase of these ac ces so ries.) T o mulching • Place deck into the high cut position. • Remove bagger or optional rear discharge deflector . • Unhook the two (2) straps and remove discharge chute.
57 5 P ara cambiar el ajuste de la segadora (Un cambio de ajuste para no recoger la hierba o usarla tipo mulching requiere la compra de los mecanismosdispositivos siguientes) Para cortar tipo mulching.
58 5 A TTENTION! • Ne jamais utiliser un tracteur sur des pentes excédant 5°. Les risques de renversement étant alors très impor - tants. • Ne jamais rouler parallèlement à la pente du fait des risques de renversement. T oujours rouler perpendiculairement à la pente, aussi bien en montant, qu'en descendant.
59 WARNING! Do not leave the ignition key in the machine when not in use to prevent children and other unauthorized persons start ing the en gine. WARNUNG! Den Zündschlüssel niemals im Zündschloß sitzen lassen, wenn die Machine unbeaufsichtigt verlassen wird, damit nicht Kinder und unbefugte Personen den Motor anlassen können.
60 6. Maintenance, adjustment. 6. W ar tung (Instandhaltung), Einstel- lung. 6. Entr etien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! Before servicing the engine or cutting unit the fol low ing shall be carried out: • Press down the clutch/brake pedal and engage the park- ing brake lever .
61 Engine hood • Raise hood. • Unsnap headlight wire connector . • Stand in front of tractor . Grasp hood at sides, tilt forward and lift off of tractor . • T o reinstall, slide hood pivot brackets into slots in frame. • Reconnect headlight wire connector and close hood.
62 6 Mantenimiento NOT A : El mantenimiento periódico ha de hacerse con regu- laridad a fin de mantener el tractor en buen estado. ADVERTENCIA : Antes de efectuar cualquier reparación, inspección o maintenimiento, desconectar el cable de la bujía a fin de evitar accidentes.
63 Pour assurer l'entretien du moteur Se référer au manuel d'utilisation du moteur . Vidange de l'huile du moteur • Retirer le bouchon (1) et placer le tuyau de vidange (2).
64 6 Change engine oil (without oil filter) ................................................... • Change engine oil (with oil filter) ............................................................................. • Lubricate pivot points ..........
65 6 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Vidange de l'huile moteur (sans filtre à huile ) ....................................................................................
66 6 DA TI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessità Ogni Ogni Ogni . Ogni Ogni 8 ore 25 ore 50 ore 100 ore 200 ore Cambio dell'olio (Senza filtro dell’olio)................................................ • Cambio dell'olio (Con filtro dell’olio) .
67 Operator Presence System and Reverse Opera- tion System (ROS) Be sure operator presence and reverse operation sys tems are work ing properly . If your tractor does not function as described, repair the problem immediately .
68 Sistema de Presencia Operador y Sistema de F uncionamiento Atrás (ROS) Asegurarse de que los sistemas de presencia operador y funcionamiento atrás funcionen adecuadamente. Si tu trac- tor no funciona como descrito, hay que reparar el problema inmediatamente.
69 6 Blades The blades should be sharp to achieve best cutting results. Sharpening can be carried out with a file or grinding disc. NOTE: It is very important that both blades are sharpened equally to avoid imbalance. Messerbalken Für ein gutes Mähergebnis müssen die messcrbalken scharf sein.
70 6 1. Hex bolt right hand threaded. 2. Lock Washer 3. Flat Washer 4. Blade 5. 5 Star Center Hole 6. 5 Star Pattern 7. T railing Edge 8. Mandrel Assembly 1. Hex bolt left hand threaded. 2. Lock Washer 3. Flat Washer 4. Blade 1. Sechskantschraube mit Rechtsgewinde 2.
71 6 1. T ornillo de cabeza de cinco facetas, dextrogiro 2. Arandela elastica 3. Arandela plana 4. Filo cortador 5. Orifico de centraje- estrella de cinco puntas 6. Mandril-estrella de cinco puntas 7. Canto (auxiliar cortador) trasero 8. Nudo del mandril 1.
72 6 For best results mower blades must be kept sharp. Re place bent or damaged blades. BL ADE REMOVAL • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and flat washer se cur ing blade. • Install new or resharpened blade with trailing edge up towards deck as shown.
73 6 T o Check Brake If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved sur - face, then brake must be serviced. Y ou may also check brake by: 1. P ark tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage park- ing brake.
74 6 Dismantling of the cutting unit Work from the right side of the machine. 1. T ake off the belt from the engine pulley (1). 2. Remove the two rear retainer springs (2) and knock off the axle taps with a hammer . Demontage des Mähdecks Arbeiten Sie auf der rechten Seite der Maschine.
75 6 Assembly of the cutting unit • Push in the cutting unit under the machine. • Assemble in the reverse order to dismantling. Einbau des Mähdecks • Mähdecks unter den T raktor schieben. • Der Einbau erfolgt in umgekehrter Reihenfolge. Mise en place du carter de coupe • Pousser le carter de coupe sous le tracteur .
76 6 Replacement of drive belt for cutting unit 1. Dismantle the cutting unit as described previously . 2. Work off the belt from the unit's left pulley and then from the other wheels. 3. Pull the belt away from the cutting unit. 4. The new belt is mounted in the reverse order .
77 6 B A 1 2 Adjustment of the cutting unit A. In the direction of travel 1. Check that the air pressure is correct in all four tires. 2. Make sure that the machine is on a horizontal surface. 3. Lift up the cutting unit to its highest position. 4. Measure the distances A and B.
78 6 “A” 2 REGL AGE TRANSVERSAL • Relever le carter de coupe au maximum. • A partir du milieu de chaque extrémités latérales du carter de coupe, mesurer la distance du bord du carter par rapport au sol . • La distance (A) doit être la même des deux côtés à 6 mm près.
79 6 2 1 3 4 5 Replacement of drive belt 1. Dismantle the cutting unit as described pre vi ous ly . 2. Dismantle the motion restrainer for the clutch (1). 3. Engage the parking brake and work off the belt upwards from the pulley (2), the clutch pul ley (3).
80 6 TRANSAXLE GEAR SHIFT LEVER NEUTRAL AD JUST MENT The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however , if adjustment is needed, proceed as follows: • Make sure transaxle is in neutral (N).
81 6 REGOL AZIONE DELL A LEVA DEL MECCANIS- MO DEL CAMBIO DI VEL OCITÀ CON DIFFER- ENZIALE Il meccanismo del cambio con differenziale deve essere in posizione di folle quando la relativa leva è in posizione di folle (N) (blocco). T ale condizione viene impostata al momento della fabbricazione.
82 7. T roubleshooting. 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Start motor will not turn engine 1. Battery flat. 2. Poor contact between cable and battery pole.
83 Le moteur ne démarre pas 1. Manque de carburant dans le réservoir . 2. Bougie d'allumage défectueuse. 3. Le câblage de la bougie d'allumage défectueux. 4. Il y a des impuretés dans le carburateur ou dans le circuit du carburant. Le démarreur n'entraîne pas le moteur 1.
84 7. Ricer ca guasti. 7. Het localiseren van fouten. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carburatore. Il motorino di avviamento non fa girare il motore 1.
85 8. Storage. 8. Aufbewahrung. 8. Remisage. 8. Conser vación. The following steps should be taken when mowing season is over: • Clean the entire machine, especially underneath the cutting unit cover . Do not use high pressure washer for cleaning. Water can enter engine and transmission and shorten the useful life of the machine.
86 8. Rismessaggio. 8. Stallen. Aan het einde van elk maaisezoen moeten de vol gen de maatregelen worden genomen: • Maak de hele machine schoon, in het bijzonder de bin- nenkant van de kap van de maaikast. Geen water onder hoge druk gebruiken om het voertuig te reinigen.
87.
532 41 08-91 Rev . 11 01.12.09 CL Printed in the U.S.A. 02682 MODEL PNC ML SERIAL NO. CA T ALOGUE NO . KW KG RPM MADE IN U.S.A. ORANGEBURG, SC 29116 2005 D P artner www .partner .biz McCulloch www .mcculloch.biz )3/ªª %# EN 1033 A (8) ≤ 2.
An important point after buying a device McCulloch HURRICANE 125 RB (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought McCulloch HURRICANE 125 RB yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data McCulloch HURRICANE 125 RB - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, McCulloch HURRICANE 125 RB you will learn all the available features of the product, as well as information on its operation. The information that you get McCulloch HURRICANE 125 RB will certainly help you make a decision on the purchase.
If you already are a holder of McCulloch HURRICANE 125 RB, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime McCulloch HURRICANE 125 RB.
However, one of the most important roles played by the user manual is to help in solving problems with McCulloch HURRICANE 125 RB. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device McCulloch HURRICANE 125 RB along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
