Instruction/ maintenance manual of the product ESV1750-14 McCulloch
Go to page of 15
PN. 249498 REV . 05 (01/06) Husqvarna Outdoor Products Italia SpA Via Como 72 23868 V almadrera (Lecco) IT ALIA Phone + 39 0341 203111 - Fax +39 0341 581671.
.
.
A. GENERAL DESCRIPTION 1) Rear handle 2) Rear hand guard 3) Front handle 4) Front hand guard/chain brake lev er 5) Chain tensioner knob/sc rew 6) Chain tensioner pin 7) Oil tank cap 8) Oil tank inspec.
ENGLISH - 2 B. SAFETY PRECAUTIONS MEANING OF SYMBOLS Warning! Read the instruction manual carefully Protective boots Protective goggles or visor, protective helmet and hearing protection Protective cu.
ENGLISH – 3 reference number of the corresponding component to draw the reader’s attention to the main safety procedure linked with that particular situation; the machine parts shown in “A – GENERAL DESCRIPTION” are indicated in italics in the text for easy identification.
ENGLISH - 4 6. Health precautions – Chemical agents. Avoid all chain oil contact with skin and eyes. 7. Health precautions - Electricity. All extension cords, plugs, and electricity lines must be homologated, to standard and in compliance with current regulations.
ENGLISH – 5 sure that the cable/ extension cord is kept behind the user, controlling that it does not create a source of danger for the user or for other persons, and check that it cannot be damaged.
ENGLISH - 6 The chain brake can be activated in two modes: the first using the left wrist by pushing forwards, or when it comes into contact with the brake system as a result of kickback; or by inertia, in the case of particularly violent kickback.
ENGLISH – 7 case do not tighten the chain immediately after use, but wait until it cools down. In cases where the loosened chain needs to be adjusted, always unscrew the bar retaining nuts / knob before adjusting the chain tensioning screw/knob ; adjust the tension and tighten the bar retaining nuts /knob accordingly.
ENGLISH - 8 Check that the chain is sharpened correctly (See below), in good working condition and that the tension is correct. If the chain is irregularly worn, or if the cutting teeth are only 3 mm high, the chain must be replaced(fig.3). Clean the air vents regularly to prevent motor overheating.
ENGLISH – 9 - At the end of each cutting operation the user will notice a considerable change in the strength necessary for controlling the machine. Great care must be taken not to loose control . Below is a description of two different types of cutting operation: Cutting action by pulling the chain (from top to bottom) (fig.
ENGLISH - 10 and lower cut. The meeting point between the two sides of the notc h is called “directional c ut line” This line must be perfectly horiz ontal at right angles (90°) to the felling direction.
ENGLISH – 11 M. TROUBLESHOOTING TABLE Motor does not start Motor turns with difficulty or loses power The machine starts but does not cut properly Motor turns improperly or at reduced speeds Braking devices do not stop the chain properly Make sure the main line is powered z Make sure the machine is properly plugged in z Make sure your cable/ext.
N. DECLARATION OF CONFORMITY The undersigned, authorized by H.O.P.I., declares that the following pro ducts model: type ES15, ES 15/1, ES 15/2, ES16, ES 16/1, ES18 starting from 2004 onwards, man ufactured by H.
An important point after buying a device McCulloch ESV1750-14 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought McCulloch ESV1750-14 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data McCulloch ESV1750-14 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, McCulloch ESV1750-14 you will learn all the available features of the product, as well as information on its operation. The information that you get McCulloch ESV1750-14 will certainly help you make a decision on the purchase.
If you already are a holder of McCulloch ESV1750-14, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime McCulloch ESV1750-14.
However, one of the most important roles played by the user manual is to help in solving problems with McCulloch ESV1750-14. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device McCulloch ESV1750-14 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
