Instruction/ maintenance manual of the product Aug-42 McCulloch
Go to page of 17
INSTRUCTION MANUAL IMP ORT AN T IN FO RM A TIO N: Plea se read t hese inst ru ctio ns caref ull y and make sur e you under st and th em befo re usi ng thi s uni t.
2 ID ENTI FIC A TIO N (WHA T IS WH A T?) Chain Adjus tment T oo l (Bar T ool) Bar O il Fill Cap Chain Front H and Guar d Starter R ope ON/S T OP Switch Muffler Chok e/ Fast Idle Lever Fuel Mix Fill Ca.
3 IDEN TIF ICA T ION OF SYM BOLS Mov e O N/ STOP s w itc h t o the ON pos ition. Slowly pres s pr imer bulb 6 times. Pull the s tarter rope shar ply 5 times w ith y our right hand. Pull th e star ter ro pe shar ply with your right hand until the engi ne starts.
4 S Keep all parts of y our body aw ay from the chain w hen the engine is running. S Keep childr en, by s tanders , and animals a minimum of 10 meters away from the work area. Do not allow other people or animals to be near the c hain s aw w hen star ting or operating the c hain saw.
5 MAINTAI N YOUR SAW IN G OOD WOR KIN G ORDE R S Hav e all c hain saw s erv ice pe rformed by a qualified s erv ic e dealer wi th the ex c eption of the items lis ted in the maintenance s ec tion of this manual .
6 S Do not attempt cuts s tart ing with the tip of the bar (plunge c uts ). S Watch for s hifting logs or other for c es that could c los e a c ut and pinc h or fall into c hain . S Us e t he R educed - - Kic kbac k Guide Bar and Low - - K ick bac k Chain spec ified for your s aw .
7 ASSE M BL Y Protec tiv e gloves (not pr ovided) s hould be worn during as sembly. A TTA CHIN G THE BUMPER SPI KE (If not already attac hed) The bumper s pike may be us ed as a piv ot when making a c ut. 1. Loosen and r emove bar knob c ompletely by lifting lev er and turning count ercloc k - wis e.
8 CHAIN TENSION (Including unit s with chain a lready inst alled) WAR N I N G : Wear protec tiv e glov es when handl ing chai n. The c hain is s harp and can c ut y ou ev en whe n it is not mov ing. NOTE: When adjus ting c hain tension, make s ure the bar knob is finger tight only.
9 OPER A T ING YOUR UN IT BEFORE ST ARTING ENGINE WAR N I N G : Be s ure to read the fuel information in the safet y rules before y ou be- gin. If you do not understand the safety rules , do not attempt to f uel your unit. Contact an authoriz ed ser vic e dealer .
10 OFF HALF CHOKE /F AST IDLE LE VER FULL 6. Pull the star ter rope s harply wit h your right hand until t he engine star ts. 7. Allow the engine to r un for approx imately 30 sec onds. T hen, squeez e and releas e throttle trigger to allow engine to r eturn to idle speed.
11 S Keep the engine at full s peed the entire time you ar e cutt ing. S Allow the c hain to cut for y ou. Ex ert only light downwar d press ure. S Releas e the throttle trigger as s oon as the cut is c ompleted, allowing the en- gine to idle. If you run the saw at full throttle without a c utting load, unnec es- sar y w ear c an occ ur .
12 Import ant p oints S Cut only one log at a time. S Cut s hattered wood v ery c arefully; shar p pieces of wood could be flung toward oper- ator . S Us e a saw hors e to c ut small logs . Nev er allow anot her per son to hold t he log while cutting and nev er hold the log with y our leg or foot.
13 S Be aler t for spr ingback . Watch out for branc hes that are bent or under press ure. Avoid being s truc k by the branch or the saw w hen the tens ion in the wood fibers is releas ed. S Keep a c lear wor k ar ea. F requently clear branc hes out of the way to av oid tripping over them.
14 After eac h us e, ensur e ON /STOP s witc h is in the STOP pos ition, then clean all s awdus t from the guide bar and spr ock et hole. T o maintain guide bar: S Move O N/STOP sw itc h to the STOP po si - tion. S Loosen an d remove b ar nuts an d c hain brak e.
15 STOR AGE WAR N I N G : Stop engine and allow to cool, and sec ure the unit before st oring or trans porting in a v ehicle. Store unit and fuel in an area wher e fuel v apors cannot r each spar ks or open flames from water heaters , electr ic motors or switc hes, furnac es, etc.
16 DECLAR A T ION OF CONF ORM ITY EC D eclaratio n of C onformi ty (O nly applies to Europe) We, H usqvarna O utdoor Products Italia, S.p.A . , V almadr era, It aly .
17 TECHNICAL DA TA S HEET Engine X-tre me 8-4 2 Cy linder volume, c m 3 42 Stroke, m m 32 Idle speed, r pm 3,000 Rec ommended max. speed, unloaded, rpm 12,000 Power , kW 1,6 Ignition syst em Manufactu.
An important point after buying a device McCulloch Aug-42 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought McCulloch Aug-42 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data McCulloch Aug-42 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, McCulloch Aug-42 you will learn all the available features of the product, as well as information on its operation. The information that you get McCulloch Aug-42 will certainly help you make a decision on the purchase.
If you already are a holder of McCulloch Aug-42, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime McCulloch Aug-42.
However, one of the most important roles played by the user manual is to help in solving problems with McCulloch Aug-42. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device McCulloch Aug-42 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
