Instruction/ maintenance manual of the product FD600.1 ARC Audio
Go to page of 10
FD600.1 FD1200.1.
2 3 W arning W e build all ARC Audio products to play at high volumes f or extended periods of time. Y our ears however are not designed f or high volume listening. This product can easily generate volumes that can permanently damage y our hearing. W e urge you to limit y our exposure to very high volume sound.
4 5 Input Section Because of the wide range of head unit output configurations all ARC Audio amplifiers hav e an adjustable input sensitivity or “Gain” . The gain is not a volume or a pow er limiting control like a throttle. It makes the amp more sensitive to input fr om the stereo .
6 7 Bridging Bridging is a way to combine the po wer of 2 channels into 1. When you wire the amp bridged y ou have a higher voltage diff erential between + and -.
8 9 Installation Instructions 1. Disconnect the negative cable from the car battery . T ape up the end so it is isolated form the battery . 2. Run the power wire (4 A WG min.) from the battery to the amplifier . Plan this part of the installation carefully .
SET PHASE TO <IN SET LO AD TO TWO > SET INUT TO NORMAL> SET PHASE TO <IN SET LO AD TO <ONE SET INUT TO NORMAL> 2 OHM OPERA TION 1 OHM OPERA TION 2 0HMS + - + _ 10D2 = 2 12D2 = 2 1 0HMS + - + _ 10D4 = 1 12D4 = 1 + _ 10D2 = 1 12D2 = 1 + _ 10D2 = 1 12D2 = 1 + _ 10D2 = 1.
SET PHASE TO <IN SET LO AD TO TWO > SET INUT TO NORMAL> SET PHASE TO OUT> SET LO AD TO TWO > SET INUT TO <SLA VE 4 OHMS BRIDGED In this configuration y ou can “Bridge” 2 amplifiers into 1 channel. T o bridge 2 amps you must set amp 1 to “Normal” and amp 2 to “Sla ve ” .
SET PHASE TO <IN SET LO AD TO <ONE SET INUT TO NORMAL> SET PHASE TO OUT> SET LO AD TO <ONE SET INUT TO <SLA VE 2 0HMS + - 2 OHMS BRIDGED + _ 10D2 = 2 12D2 = 2 + _ 10D4 = 2 12D4 = 2 + _ 10D4 = 2 12D4 = 2 + _ 10D4 = 2.66 12D4 = 2.66 In this configuration y ou can “Bridge” 2 amplifiers into 1 channel.
16 17 Battery Battery Battery or Capacitor 4 A WG. 18” MAX. 4 A WG.18” MAX. 18” MAX. 18” MAX. 4 A WG.18” MAX. 4 A WG. 4 A WG. 4 A WG. 4 A WG.
Specifications 19 18 FD1200.1 20 Hz > 250Hz >89 dB >NA > 2100 55Hz - 250Hz .25V - 2.5V 0 - 18dB @ 30Hz - 80Hz 510 Watts 1010 Watts 1100 Watts 110A @ 1100W atts 10 3/8 ” X 21 3/4 ” X 2 3/8 ” FD600.1 Bass Output Power (RMS) @ .05% 1000z 14.
An important point after buying a device ARC Audio FD600.1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ARC Audio FD600.1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ARC Audio FD600.1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ARC Audio FD600.1 you will learn all the available features of the product, as well as information on its operation. The information that you get ARC Audio FD600.1 will certainly help you make a decision on the purchase.
If you already are a holder of ARC Audio FD600.1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ARC Audio FD600.1.
However, one of the most important roles played by the user manual is to help in solving problems with ARC Audio FD600.1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ARC Audio FD600.1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
