Instruction/ maintenance manual of the product 8269550 Maytag
Go to page of 13
Part No. 8269550 Rev . A N° de pièce 8269550 Rév . A Printed in U.S.A. Imprimé aux É.-U. Installation Instr uctions Undercounter Dishw asher What do I need to have to install the dishwasher? What.
V otre sécurité et celle des autres sont très importantes. Nous donnons de nombreux messages de sécurité impor tants dans ce manuel et sur v otre appareil ménager . Assurez-vous de toujours lire tous les messages de sécurité et de vous y conf or mer .
4 Cabinet opening Requirements Spécifications C heck location where dishwasher will be installed. The location must provide: ✔ easy access to water , electricity and drain. ✔ convenient loading. Corner locations require a 2" (5.1 cm) minimum clearance between the side of the dishwasher door and wall or cabinet.
continued from page 4 W ater Y ou must ha ve: ✔ a hot water line with 20-120 psi (138-862 kPa) water pressure. ✔ 120°F (49°C) water at dishwasher . ✔ 3/8" O.D. copper tubing with compression fitting or flexible stainless steel braided fill line(1/2" minimum plastic tubing is optional but not recommended).
A. Prepare cabinet Préparation de l’encastrement 1. 2. Disconnect the power supply . T urn water off. Déconnecter la canalisation d’arrivée d’eau. Fermer l’eau. Put on gloves and safety glasses. Porter des gants et des lunettes de sécurité.
10 continued from page 8 suite de la page 8 4a. 6. 7. 8. 9. HELPFUL TIP: Routing the water line through the left side of cabinet opening will make w ater connection easier . CONSEIL UTILE : F aire passer la canalisation d’eau du côté gauche de l’ouver ture du placard facilitera le raccord.
continued from page 10 suite de la page 10 11c. 11d. 1. Cut end of drain hose (do not cut ribbed section). 2. Attach drain hose to waste tee with 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp * . This connection MUST be before drain trap and at least 20" (50.
4. Remove terminal box cover . Pull appliance wires through hole in terminal box. Do not untie the knot in the wires. Ôter le couvercle de la boîte de connexion. Faire passer les fils de l’appareil dans le trou de la boîte de connexion.
HELPFUL TIP: Built-up floors. T ilt dishwasher backward to move into opening. Once in position, support front of dishwasher by lowering or shimming front feet. Une fois dans sa position, soutenir l’avant du lave-vaisselle en baissant les pieds avant ou en plaçant des cales en dessous.
17 18 Electrical Connection HELPFUL TIP: • Select the proper size twist-on connectors to connect your household wiring to 16-gauge dishwasher wiring. • Inser t wire ends into twist-on connector . Do not pre-twist bare wire. • T wist connector . • Gently tug on wires to be sure both are secured.
20 19 HELPFUL TIP: Compression fittings: 1. Slide nut onto copper tubing about 1 inch (2.5cm). 2. Slide ferr ule onto the tubing. Do not position ferr ule on the end of the tubing. 3. Put the tubing into the elbow as far as it will go.
22 21 D. Secure Dishw asher 1. 3. Open dishwasher door and place towel over pump assembly and spray arm of dishwasher . This will prevent screws from falling into pump area when securing dishwasher to countertop. Check that dishwasher is still level and centered in the opening.
Part No. 8269550 Rev . A N° de pièce 8269550 Rév . A Printed in U.S.A. Imprimé aux É.-U. Installation Instr uctions Undercounter Dishw asher What do I need to have to install the dishwasher? What.
An important point after buying a device Maytag 8269550 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Maytag 8269550 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Maytag 8269550 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Maytag 8269550 you will learn all the available features of the product, as well as information on its operation. The information that you get Maytag 8269550 will certainly help you make a decision on the purchase.
If you already are a holder of Maytag 8269550, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Maytag 8269550.
However, one of the most important roles played by the user manual is to help in solving problems with Maytag 8269550. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Maytag 8269550 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center