Instruction/ maintenance manual of the product ST3250312CS Maxtor
Go to page of 46
Product Manual Pipeline HD.2 Series SA T A 100529372 Rev . A January 2009 ST31000424CS ST31000322CS ST3500414CS ST3500312CS ST3250312CS.
Revision history Copyright © 2009 Seagate T echnology LLC. All right s reserved. Printed in U.S.A. Publication number: 100529372, Rev . A January 2009 Seagate, Seagate T echnology and the W ave logo ar e registere d trademarks of Seagate T echnology LLC in the United S tates and/or other countries.
Pipeline HD.2 Series SATA Product Manual, Rev. A i Contents 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . .
ii Pipeline HD.2 Series SAT A Product M anual, Rev. A.
Pipeline HD.2 Series SATA Product Manual, Rev. A iii List of Figures Figure 1. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 2. Serial ATA connectors . . . . . . . . . .
.
Pipeline HD.2 Series SATA Product Manual, Rev. A 1 1.0 Introduction This manual describes the functiona l, mechanical an d interface specifications for the following Seagate Pipeline HD TM .2 Series model d rive: These drives provide the following key fea tures: • High instant aneous (burst) da ta-tr ansfer rates (up to 30 0 Mbytes per second).
2 Pipeline H D.2 Series SAT A Product Ma nual, Rev. A 1.1 About the Serial A T A interface The Serial A T A interface pr ovides several advant ages over the traditional (p arallel) A T A interface. The primary advantages include : • Easy installation and configuration with true plug-and-pla y connectivity .
Pipeline HD.2 Series SATA Product Manual, Rev. A 3 2.0 Drive specifications Unless otherwise noted, all specific ations are me asured unde r ambient conditions, at 25°C, and nominal power . For convenienc e, the ph rases the drive and this drive are used throughout this manual to in dicate the following drive model: 2.
4 Pipeline H D.2 Series SAT A Product Ma nual, Rev. A T able 1: Drive specifications summary for 1000 Gbyte mo dels Drive specification ST31000424CS ST31000322CS Formatted capacity (512 bytes/sector)*.
Pipeline HD.2 Series SATA Product Manual, Rev. A 5 * On e Gbyte equals one billion bytes when referring to hard driv e capacity. Accessible capacity may vary depending on operating envir onment and formatting. * *During pe riods of drive idle, some offli ne activity may occur according to the S.
6 Pipeline H D.2 Series SAT A Product Ma nual, Rev. A T able 2: Drive specifications summary for 500 and 250 G byte mode ls Drive specification ST3500414CS ST3500312CS ST3250312CS Formatted capacity (.
Pipeline HD.2 Series SATA Product Manual, Rev. A 7 * On e Gbyte equals one billion bytes when referring to hard driv e capacity. Accessible capacity may vary depending on operating envir onment and formatting. * *During pe riods of drive idle, some offli ne activity may occur according to the S.
8 Pipeline H D.2 Series SAT A Product Ma nual, Rev. A 2.2 Formatted cap acity *One Gbyte equals one billion bytes when referri ng to hard drive capacity.
Pipeline HD.2 Series SATA Product Manual, Rev. A 9 2.5 Physical characteristics 2.6 Seek time Seek measurement s are t aken with nominal p ower at 25°C ambient temperatur e.
10 Pipeline HD.2 Series SAT A Product M anual, Rev. A 2.8 Power specifications The drive receives DC power (+ 5V or +12V) thro ugh a na tive SA T A power connector . See Figure 3 on page 20. 2.8.1 Power co nsumption Power requirement s for the drives are listed in the table on page 9.
Pipeline HD.2 Series SATA Product Manual, Rev. A 1 1 2.8.1.1 T ypical curren t profiles Figure 1. T y pical 12V startup and operation curre nt profile 2.
12 Pipeline HD.2 Series SAT A Product M anual, Rev. A 2.8.4 Power-man agement mo des The drive provides prog rammable power man agement to provide gr eater energy ef fici ency . In most systems, you can control power manage ment through the system setup program.
Pipeline HD.2 Series SATA Product Manual, Rev. A 1 3 2.9 Environment al specifications 2.9.1 Drive case temperatu re Above 1,000 feet (305 me ters), the maximum temper ature is dera ted linearly to 1 12°F (44°C) at 10,000 feet (3,048 meters). Drive case temperature should be me asured at t he locatio n indicated in Figure 4 on page 21.
14 Pipeline HD.2 Series SAT A Product M anual, Rev. A 2.9.5 Shoc k All shock specifications assu me that the drive is mounted secu rely with the input sh ock applied at the drive mounting screws.
Pipeline HD.2 Series SATA Product Manual, Rev. A 1 5 2.10 Acoustics emissions Drive emission of so und is measured consistent with the ECMA-74 an d its referenced standards.
16 Pipeline HD.2 Series SAT A Product M anual, Rev. A 2.12 Reliability 2.12.1 Annualized Failure Rate (AFR) The product shall achieve an Annualized Failu re Rate (A FR) of 0.55% when opera ted in an environ ment of ambient air temperatures of 25 ° C.
Pipeline HD.2 Series SATA Product Manual, Rev. A 1 7 Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) log o, they comply with par a- graph 1 of Article 1 1 of .
18 Pipeline HD.2 Series SAT A Product M anual, Rev. A 2.14 Environment al protection Seagate designs it s product s to meet en vironment al pr otection requirement s worldwide, including regulations restricting certain chemical substances.
Pipeline HD.2 Series SATA Product Manual, Rev. A 1 9 3.0 Configuring and mounting the drive This section contains the specif ications an d instructions for configuring and mounting the drive.
20 Pipeline HD.2 Series SAT A Product M anual, Rev. A 3.2 Configuring the drive Each drive on the Seri al A T A interface connect s point-to-point with the Serial A T A host ada pter . There is no master/slave rela tionship becaus e each drive is consider ed a master in a point- to-point relationship .
Pipeline HD.2 Series SATA Product Manual, Rev. A 2 1 3.4 Drive mounting Y ou can mount the drive in any orient ation using four screws in the side-mounting holes or four screws in the bottom-mo unting hole s. See Figure 4 for drive mo unting dime nsions.
22 Pipeline HD.2 Series SAT A Product M anual, Rev. A Figure 5. Mounting dimen sions (for 5 00 and 250 GB models) Recommended case temperature measurement location.
Pipeline HD.2 Series SATA Product Manual, Rev. A 2 3 4.0 Serial A T A (SA T A) interface These drives use the industry-s tandar d Serial A T A interfac e th at support s FIS dat a transfers. It support s A T A programmed input/o utput (PIO) modes 0–4; mult iword DMA modes 0–2, and Ultr a DMA modes 0–6.
24 Pipeline HD.2 Series SAT A Product M anual, Rev. A 4.2 Serial A T A device p lug connector pin definitions Table 6 summarizes the sig nals on the Se rial ATA interface and power co nnectors. Notes: 1. All pins are in a single row , with a 1.27 mm (0.
Pipeline HD.2 Series SATA Product Manual, Rev. A 2 5 4.3 Supported A T A commands The following t able list s Serial A T A standa rd commands that the drive support s. For a deta iled description of the A T A commands, re fer to the Se rial A T A Internatio nal Organization: Seria l A T A Revision 2.
26 Pipeline HD.2 Series SAT A Product M anual, Rev. A Security Erase Unit F4 H Security Freeze F5 H Security Set Password F1 H Security Unlock F2 H Seek 70 H Set Features EF H Set Max Address F9 H Note: Individual Set Max Address commands are identifie d by the value placed in the Set Max Features regis - ter as defined to the right.
Pipeline HD.2 Series SATA Product Manual, Rev. A 2 7 4.3.1 Identify Dev ice command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The da ta is organized as a sing le 512-byte block of data, whose contents are sho wn in T abl e 7 on page 25.
28 Pipeline HD.2 Series SAT A Product M anual, Rev. A 60–61 T otal number of user-addressable LBA sectors availabl e (see Section 2.2 for related information) *Note: The maximum value all owed in this field is: 0FFF FFFFh (268,435,455 sectors, 137 Gbytes).
Pipeline HD.2 Series SATA Product Manual, Rev. A 2 9 Note. Advance d Power Management (APM) and Automatic Acou stic Manage ment (AAM) feat ures are not supp orted Note. See the bit descriptio ns below for words 63 , 84, and 88 of the Identify Drive data.
30 Pipeline HD.2 Series SAT A Product M anual, Rev. A Bit Wor d 8 8 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported.
Pipeline HD.2 Series SATA Product Manual, Rev. A 3 1 4.3.2 Set Featu res command This command controls the implement ation of various fe at ures that th e drive support s. When the drive receives this command, it sets BSY , checks the contents of the Featur es register , clears BSY and gen erates an inter- rupt.
32 Pipeline HD.2 Series SAT A Product M anual, Rev. A 4.3.3 S.M.A.R.T . commands S.M.A.R.T . provides near-term failure prediction fo r disc drives. When S.M.A.R.T . is enabled, the d rive moni- tors predetermined drive attributes that are suscep tible to degradation over time.
Pipeline HD.2 Series SATA Product Manual, Rev. A 3 3 5.0 Seagate T echnology support services Online services Internet For information regardin g Seagate product s and services, visit www .sea gate.com . Worldwide support is available 24 hours daily by ema il for your questions.
34 Pipeline HD.2 Series SAT A Product M anual, Rev. A Customer Service Operations W arranty Servi ce Seagate of fers worldwide customer support for Seagate product s. Seagate distributor s, OEMs and othe r direct customers should contact their Seagate Customer Ser v ice Operat ions (CSO) repr esentative for warr anty- related issues.
Pipeline HD.2 Series SATA Product Manual, Rev. A 3 5 Index A ACA 17 acceleration 14 acoustics 15 Active 12 Active m ode 12 AFR 16 Agency certification 16 altitude 13 ambient temper ature 9 , 10 Annual.
36 Pipeline HD.2 Series SAT A Product M anual, Rev. A Identify Devic e command 27 Idle 12 , 25 Idle Immediat e 25 Idle mode 10 , 12 IEC950 16 Information Technology Equipm ent (ITE) 16 Initialize Devi.
Pipeline HD.2 Series SATA Product Manual, Rev. A 3 7 S.M.A.R.T. Save Attribute Values 26 S.M.A.R.T. Write Log se ctor 26 Safety certification 16 SATA 23 screws 14 sectors 8 Sectors per track 8 Securit.
38 Pipeline HD.2 Series SAT A Product M anual, Rev. A.
.
Seagate T echnology LLC 920 Disc Drive, Scotts V a lley , California 95066 -4544, USA Publication Number: 1005293 72, Rev . A, Printed in U.S.A..
An important point after buying a device Maxtor ST3250312CS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Maxtor ST3250312CS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Maxtor ST3250312CS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Maxtor ST3250312CS you will learn all the available features of the product, as well as information on its operation. The information that you get Maxtor ST3250312CS will certainly help you make a decision on the purchase.
If you already are a holder of Maxtor ST3250312CS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Maxtor ST3250312CS.
However, one of the most important roles played by the user manual is to help in solving problems with Maxtor ST3250312CS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Maxtor ST3250312CS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
