Instruction/ maintenance manual of the product MM-6280IND Maxon Telecom
Go to page of 60
HSDP A S t andard A T Commands Manual VERSION 1. 2 This document is the sole and exclusive property of Maxon. Not to be distributed or divulged without prior written agreement .
HSDPA Standard At Commands Page 2 of 60 Version 1.2 Document Description All data and information con tained in or discl osed by this d ocument are co nfidenti al and proprietary information o f Maxon Australia, an d all rights therein are expressly reserved.
HSDPA Standard At Commands Page 3 of 60 Version 1.2 REVISION HIST OR Y Product Name Maxon ModMax - MM-6280IND Document Type Public Document Number CHE-FDS-2301 Current Version Number 1.2 Status of the Docume nt Public Release Revision Date 2007-12-13 Total Number of Pages 60 - Revision History Level Date History 1.
HSDPA Standard At Commands Page 4 of 60 Version 1.2 CONT ACT INFORMA TION Depending on t he nature of your inqu iry, plea se feel free to contact the following senior personnel: Sales, Marketing & Corp orate: Ray Sanders – Managing Director Email: rayws@maxon.
HSDPA Standard At Commands Page 5 of 60 Version 1.2 T ABLE OF CONTENTS HSDPA Standard AT Commands Manual .................................................................................... 1 Document Description ......................................
HSDPA Standard At Commands Page 6 of 60 Version 1.2 1.24. Read operator names +COPN ...........................................................................................30 1.25. Informative examples ..............................................
HSDPA Standard At Commands Page 7 of 60 Version 1.2 Introduction 1.1. General The 3GPP TS 27.007 technical specification define s an AT command set for use in cont rolling devices that operate on WCDMA networks. This docu ment identifies which of those AT commands are supported on the CHU628 USB modem module.
HSDPA Standard At Commands Page 8 of 60 Version 1.2 Term Description MSC Mobile Switching Centre MT Mobile-Terminated where the SMS or the call is terminated [rec eived] at the Mobile Station. MT2 Mobile Termination 2An MT2 provide s a non-ISDN (Rm) user interface, e.
HSDPA Standard At Commands Page 9 of 60 Version 1.2 3GPP TS 22.081 3rd Generation Partnership Project; Line ident ification supplementary services - Stage 1. 3GPP TS 22.082 3rd Generation Partnership Project; Call Forwar ding (CF) supplementary services - Stage 1".
HSDPA Standard At Commands Page 10 of 60 Version 1 .2 Portable Computer and Communications As sociation PCCA STD-101 Data Tra nsmission Systems and Equipment Serial Asynchronous Automatic Dialling and Control for Chara cter Mode DCE on Wireless Data Services.
HSDPA Standard At Commands Page 11 of 60 Version 1 .2 A T INTERF ACE DESCRIPTION 1.4. Basic Integration The MM-6280IND support s asyn chronous serial communication known as RS-232 or USB. This chapter describes the basi c integration and co mmunication of MT2 with TE2.
HSDPA Standard At Commands Page 12 of 60 Version 1 .2 The following diagram sho ws the naming convention of messages between MT2 and TE2. Figure 1. Naming convention diag ram 1.8. DTE-TA/DCE interface commands Table 3. ITU-T V.250 commands relating to TE-TA interface Command Req Description Support E<value> Mand.
HSDPA Standard At Commands Page 13 of 60 Version 1 .2 4800, 9600, 19200), (45, 50, 75, 110, 150, 30 0, 600, 38400, 57600, 115200, 230400) +IPR=<value > Set value +ICF Opt.
HSDPA Standard At Commands Page 14 of 60 Version 1 .2 3 Xon/Xoff global DC1/DC3 on circuit 103 wi th DC1/DC3 characters being passed throug h to the remote DCE in addition to being acted upon for loca.
HSDPA Standard At Commands Page 15 of 60 Version 1 .2 Mobile T ermination errors commands Table 4. Mobile Termination control and status commands Command Req Description Support +CMEE Report Mobile Termination erro r supported 1.
HSDPA Standard At Commands Page 16 of 60 Version 1 .2 7 PH-FSIM PUK required 10 SIM not inserted (Note) 11 SIM PIN required 12 SIM PUK required 13 SIM failure (Note) 14 SIM busy (Note) 15 SIM wrong (N.
HSDPA Standard At Commands Page 17 of 60 Version 1 .2 100 Unknown 1.10. Informative examples An example of TA respon ses with all three +CMEE values when MT ma nufacturer identification is requested b.
HSDPA Standard At Commands Page 18 of 60 Version 1 .2 General commands ITU-T Recommendation V.250 [14] includes "Generic DCE Co ntrol" commands with the prefix +G. These commands are for the identific ation of the TA. Four of those commands are adapted h ere to be the identification commands of the MT.
HSDPA Standard At Commands Page 19 of 60 Version 1 .2 Table 8. +CGMM action command syntax Command Possible respon se(s) +CGMM <model> +CME ERRO R: <err> +CGMM=? value <model>: the total number of characters, in cluding line terminators, in the information text shall not exceed 2048 characters.
HSDPA Standard At Commands Page 20 of 60 Version 1 .2 1.15. ITU-T V.250 generic TA control commands Table 11. ITU-T V.250 generic TA control commands Command Req Description Support Z[<value>] Mand.
HSDPA Standard At Commands Page 21 of 60 Version 1 .2 command +<name>s, whi ch is intended to permit the user of the MT2 to identify the minimum capabilities of the MT2.
HSDPA Standard At Commands Page 22 of 60 Version 1 .2 1.17.6. Supported alphabets Command: AT+CSCS=? Expected response: +CSCS: (“alphabet1”,”al phabet2”,…) Command: AT+CSCS=”Alphabet” Expected response: OK if chosen alphab et is supported or ERROR 1.
HSDPA Standard At Commands Page 23 of 60 Version 1 .2 Network service commands UMTS network related command s, which are not covered in call control clause of the present document. Commands include UMTS MSISDN query, MT and network facility locking, and netwo rk registration information que ry Table 13.
HSDPA Standard At Commands Page 24 of 60 Version 1 .2 +CCFC Mand. Call forwarding number and con dition s NA +CCWA Opt. Call waiting NA +CHLD Opt. Call related supplem entary services NA +CTFR Opt. Call deflection Not supported +CUSD Opt. Unstructured supple mentary service d ata NA +CAOC Opt.
HSDPA Standard At Commands Page 25 of 60 Version 1 .2 Table 15. +CREG parameter command sy ntax Command Possible response(s) +CREG=[<n>] +CREG? +CREG: <n>,<stat>[,<lac>,<ci&.
HSDPA Standard At Commands Page 26 of 60 Version 1 .2 Test command returns a set of five parameters, each representing an operator present in the network.
HSDPA Standard At Commands Page 27 of 60 Version 1 .2 2 current 3 forbidden <AcT> access technology selected : 0 GSM 1 GSM Compact 2 UTRAN 1.21. Facility lock +CLCK Execute command is used to lock, unlock or i nterrogate a M T or a network f acility <fac> .
HSDPA Standard At Commands Page 28 of 60 Version 1 .2 value <fac> values reserved by the present document: "CS" CNTRL (lock CoNTRoL surface (e.
HSDPA Standard At Commands Page 29 of 60 Version 1 .2 1.22. Change password +CPWD Action command sets a new passw ord for the facility lock f unction defined by comma nd Facility Lock +CLCK .
HSDPA Standard At Commands Page 30 of 60 Version 1 .2 Table 19. +COLP parameter command sy ntax Command Possible response(s) +COLP=[<n>] +COLP? +COLP: <n>,<m> +COLP=? +COLP: (list of.
HSDPA Standard At Commands Page 31 of 60 Version 1 .2 3: use for set format, see below 4: manual/automatic. If manual choice fa ils then make an automatic registration Format possible values: 0: short alphanumeric format 1: long alphanumeric format 2: numeric format name is operator name co rresponding to the fo rmat.
HSDPA Standard At Commands Page 32 of 60 Version 1 .2 Mobile T ermination control and st atus commands 1.26. Basic TE Table 21. Basic TE Comman d Req Description Support +CPAS Mand . Phone activity status Not Supported +CFUN Opt. Set phone functionality Not Supported +CMA`R Opt.
HSDPA Standard At Commands Page 33 of 60 Version 1 .2 +CRSM Opt. Restricted SIM access Supported +CPIN Mand . Enter PIN Supported +CGLA Generic UICC Logical Ch annel a ccess Not supported +CRLA Opt. Restricted UICC Logica l Channel acce ss Not supported +CCHO Opt.
HSDPA Standard At Commands Page 34 of 60 Version 1 .2 1.29. Band Selection (AT$$MBAND) This command is used to read and write of the band selectio n. Table 24. AT$$MBAND Read Command Command TE2 Æ MT2 $$MBAND? <CR> Response TE2 Å MT2 $$MBAND: [result value] <CR> <result_code>( OK | ERRO R) Result Value 0 : auto 1 : 850MHz 2 : 2.
HSDPA Standard At Commands Page 35 of 60 Version 1 .2 Value “ READY ” MT is not pe nding for any password “ SIM PIN ” MT is waiting SIM PIN to be give n “ SIM PUK ” MT is waiting SIM PUK t.
HSDPA Standard At Commands Page 36 of 60 Version 1 .2 1 -111 dBm 2...30 -109 ... -53 dBm 31 -51 dBm or greater 1.31.2. Pin registration The application just allows for an em ergency call until PIN cod.
HSDPA Standard At Commands Page 37 of 60 Version 1 .2 Packet Domain Command(GPRS) 1.32. UMTS packet Domain commands This clause defines commands that a TE may u se to c ontrol a MT supporting packet switched services. Other aspects of a Packet Domain MT are described in 3GPP TS 27.
HSDPA Standard At Commands Page 38 of 60 Version 1 .2 +CGANS Opt. Manual response to a network request for PDP context activation Not supported +CGCLASS Opt. GPRS mobile station class Supported +CGCLPAD (GPRS only) Opt. Configure local triple-X PAD parameters Not supported +CGEREP Opt.
HSDPA Standard At Commands Page 39 of 60 Version 1 .2 returned by the test form of the command. <PDP_type> : (Packet Data Protocol type) a string parameter which specifies the type of packet data protocol X.
HSDPA Standard At Commands Page 40 of 60 Version 1 .2 Table 29. +CGDCONT parameter command syntax Command Possible response(s) +CGDSCONT=[<cid> , <p _ cid> [,<d _ comp> [,<h_comp&.
HSDPA Standard At Commands Page 41 of 60 Version 1 .2 related context. Since this is the same pa rameter that is used in th e +CGDCONT and +CGDSCONT comman ds, the +CGTFT command is e ffectively an extensio n to these commands. The Packet Filters cons ist of a number of para meters, each of which may be set to a separate value.
HSDPA Standard At Commands Page 42 of 60 Version 1 .2 +CGTFT? +CGTFT: <cid>, <packet filter identifier>, <evaluation precedence index>, <source address and subnet mask>, <pr.
HSDPA Standard At Commands Page 43 of 60 Version 1 .2 parameters on the form 'f.t'. <source port range> :Consists of dot-separated numeric (0-65535) parameters on the form 'f.t'. <ipsec security parameter index (spi)> : Hexadecimal parameter, value range from 00000000 to FFFFFFFF.
HSDPA Standard At Commands Page 44 of 60 Version 1 .2 +CGQREQ=? +CGQREQ: <PDP _ type>, (list of supported <precedence>s), (list of supported <delay>s), (list of supported <reliabi.
HSDPA Standard At Commands Page 45 of 60 Version 1 .2 +CGQMIN=? +CGQMIN: <PDP _ type>, (list of supported <precedence>s), (list of supported <delay>s), (list of supported <reliabi.
HSDPA Standard At Commands Page 46 of 60 Version 1 .2 [,<Traffic handling priority> ]]]]]]]]]]]]] +CGEQREQ? +CGEQREQ: <cid>, <Traffic class> ,<Maximum bitrate UL> ,<Maximum .
HSDPA Standard At Commands Page 47 of 60 Version 1 .2 3 - background 4 - subscribed value If the Traffic class is specified as conversational or streaming, then the Guaranteed and Maximum bitrate parameter s should also be provided. Other values are reserved.
HSDPA Standard At Commands Page 48 of 60 Version 1 .2 SDUs. If no error detection is requested, Residual bit error ratio indicates the bit error ratio in the delivered SDUs. The value is specified as 'mEe'. As an example a target residual bit error ratio of 5•10 -3 would be specified as '5E3' (e.
HSDPA Standard At Commands Page 49 of 60 Version 1 .2 Table 34. + CGEQMIN parameter command syntax Command Possible response(s) +CGEQMIN=[<cid> [,<Traffic class> [,<Maximum bitrate UL&g.
HSDPA Standard At Commands Page 50 of 60 Version 1 .2 <Delivery order>s) ,(list of supported <Maximum SDU size>s) ,(list of supported <SDU error ratio>s) ,(list of supported <Resi.
HSDPA Standard At Commands Page 51 of 60 Version 1 .2 Other values ar e reserved. <Maximum SDU size>: a numeric param eter (1,2,3,…) that indicates the maximum allowed SDU size i n octets (refer TS 24.
HSDPA Standard At Commands Page 52 of 60 Version 1 .2 The test command returns a list of <cid> s associated with active contexts Table 35. +CGEQNEG action command syntax Command Possible respons.
HSDPA Standard At Commands Page 53 of 60 Version 1 .2 Other values ar e reserved. <Maximum SDU size>: a numeric parameter that (1,2,3,…) i ndicates the maximum allowed SDU size in octets (refe r TS 24.
HSDPA Standard At Commands Page 54 of 60 Version 1 .2 Table 36. + CGATT parameter command syntax Command Possible response(s) +CGATT= [ <state> ] OK ERROR +CGATT? +CGATT: <state> +CGATT=? .
HSDPA Standard At Commands Page 55 of 60 Version 1 .2 1.32.11. PDP Context Modify +CGCMOD The execution command is us ed to modify the specified PDP context (s) with repect to QoS prof iles a nd TFTs . Afte r the command has co mple ted, the MT re turns to V.
HSDPA Standard At Commands Page 56 of 60 Version 1 .2 The PDP type must match exactly. The PDP a ddresses are considered to match if they are identical or if either or bot h addresses are unspecified.
HSDPA Standard At Commands Page 57 of 60 Version 1 .2 Table 40. + CGPADDR para met er command s ynta x Command Possible response(s) +CGPADDR=[<cid> [,<cid> [,…]]] +CGPADDR: <cid>,<PDP_addr> [<CR><LF>+CGPADDR: <cid>,<PDP_addr> [.
HSDPA Standard At Commands Page 58 of 60 Version 1 .2 Synchronous dat a mode commands Table 42. ITU-T V80ter Synchronous data mod e command Command Req Description Support +ES=<orig_rq st> <o.
HSDPA Standard At Commands Page 59 of 60 Version 1 .2 Qualcomm commands Table 43. Qualcomm command COMMAND Description Opera tion Support $QCCLR clear mobil e error log Clears the mobile error log Sup.
HSDPA Standard At Commands Page 60 of 60 Version 1 .2 <passw ord>, <username> 0 None 1 PAP 2 CHAP additional parameters are required, as follows: 0 – Neither username nor password accepted 1 – Username and password accepted 2 – Only password (secret) accepted Query command, i.
An important point after buying a device Maxon Telecom MM-6280IND (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Maxon Telecom MM-6280IND yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Maxon Telecom MM-6280IND - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Maxon Telecom MM-6280IND you will learn all the available features of the product, as well as information on its operation. The information that you get Maxon Telecom MM-6280IND will certainly help you make a decision on the purchase.
If you already are a holder of Maxon Telecom MM-6280IND, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Maxon Telecom MM-6280IND.
However, one of the most important roles played by the user manual is to help in solving problems with Maxon Telecom MM-6280IND. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Maxon Telecom MM-6280IND along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
