Instruction/ maintenance manual of the product SA-17S1 Marantz
Go to page of 46
Super A udio CD Pla yer SA-17S1 08AK855010 MIT First Issue 2002.12 T ABLE OF CONTENTS SECTION PA G E 1. TECHNICAL SPECIFICA TIONS .................................................................................................. .1 2. SER VICE MODE ..
MARANTZ DESIGN AND SER VICE Using superior design and selected high grade components, MARANTZ compan y has created the ultimate in stereo sound. Only original MARANTZ par ts can insure that your MARANTZ product will continue to perf or m to the specifi cations f or which it is f amous.
1 Super A udio CD CD A udio Characteristics Analog output Channels 6channels (Max.) 2channels F requency range 2Hz — 100kHz 2Hz — 20kHz F requency characteristics 2Hz — 50kHz (-3dB) 2Hz — 20kHz Dynamic range 114dB 100dB THD (1kHz) 0.0008% 0.0020% W ow & Flutter Precision of quar tz Precision of quar tz Output le vel 2.
2 2. SER VICE MODE 2-1. Factory mode While pressing < OPEN/CLOSE >and< NEXT >plug in the Mains cord. "SA-17S1" is displa yed Press< > V ersion of Back end(QF01) u-COM is displa yed "V er : X.XX" is display ed Press< > V ersion of F rontend(Q125) µ-COM is displayed "Dr vV er : XX.
3 3. T AKING THE DISC OUT OF EMERGENCY 1. Remov e 8 screws on the top cov er and remove the top co ver . 2. Remov e 6 screws on the side panel and remov e the side panel. 3. Rem o v e P o w er S W . Link. 4. Remov e 4 screws pointed with the arrows. 5.
4 4. CA UTION Optical pick up and Serv o Board When removing the fl at wire between Optical pick up and Servo Board (PV16), Solder the f our lands pointed by arro ws to shor t the circuit. Otherwise the LASER DIODE ma y be damaged by static electricity .
5 6 5. BLOCK DIA GRAM SACD UNIT BLOCK DAC PWB L.ch L.ch DAPC DARD DACL R.ch LRCK DSAC DSALS 33.8688MHz DSARS DSALF Rch SYSTEM CLK SYCL Control data bus line PCM data bus line MODE CENTER CENTER WOOFER.
8 7 6. SCHEMA TIC DIA GRAM CAOX OPT DIGO FRES FCEN FCLK FDAT KEY1 KEY0 KEY0 KEY1 FDAT FCLK FCE N FRE S DIGO MODE1 H2 -VFT H1 DISPLED RC5S DISPLE D -VFT RC5S +5A +5A GND GND KEY0 KEY1 FDAT FCLK FCEN FR.
9 10 VREF DARDO DAPCO DALR DACL M2 M3 M41 RST RST M41 M3 M2 SYCL DACL DALR DARD DAPC DALR M3 M42 DACL M2 DALR M3 M2 DACL M43 SYCL SYCL SYCL RST M42 DSALS DSARS DSALF M43 PTMON PTMON DSACO DAPC DAPCO D.
12 11 DVDRFP SDF N RX MEVO MI N MLPF MB MP MIRR LDON VNB PD-CD PD-DVD CDLD DVDLD VC VPB CD-E CD-F MFV VNA ENN ENP DIP DIN BYP RFAC VPA AP AIN ATON AT0P RFSIN RFD C DVDRFN A2 B2 C2 D2 CP CN D C B A CD-.
13 14 XRESET DRVIRQ DRVRDY1 DRVTX DRVRX MSRADY MSDTI MSDTO MSCK XMSLAT REQST DSPSCK DSPSDT DSPXLAT FOK SENS SQSO SNSCK SQCK AMPMNT SCSY GFSDSP MIRR FJUP_D FJUP_U XFCMP_L XFCMP_H XINT1 XINT0 DECD7 DECD.
16 15 VSCO(GND) XMSLAT MSCK MSDATI VDCO(2.5V) MSDATO MSRADY (NC)MSDOE XRST XMU T DSD768fs VSIO0(3.3V) EXCKO1(384fs) EXCKO2(256fs) (NC)LRCKI (NC)F75HZ VDIO0(3.3V) MNT0 MNT1 MNT2 (NC)MNT3 (NC)MNT4 (NC)MNT5 (NC)MNT6 (NC)MNT7 TCK (NC)TDI VSC1(GND) (NC)TDO (NC)TMS TRST TEST1 SD7 SD6 SD5 SD4 SD3 SD2 SD1 SD0 SDEF XSAK SDCK XSHD XSRQ VDIO7(3.
17 18 49 G6 18 AM18 19 AM19 20 AM20 21 AM21 22 AM22 23 AM23 24 AM24 25 AM25 26 AM26 27 AM27 28 AM28 29 AM29 30 AM30 31 AM31 48 G7 47 G8 46 G9 45 G10 44 G11 43 G12 42 G13 41 AA 6 40 AA 5 39 AA 4 38 AA .
20 19 7. P ARTS LOCA TION + - RC5S LPFSW RC5F C B E C B E G D S G D S C B E C B E C B E G D S C B E C B E G D S C B E G D S G D S C B E G D S G D S C B E 1 2 3 1 2 3 1 2 4 3 654 321 321 654 1 +5VD 2 G.
21 22 P A16 Q609 Q611 - Q616 Q617 - Q624 Q659 Q661 - Q666 Q667 - Q674 Q409 Q411 - Q416 Q417 - Q424 Q459 Q461 - Q466 Q467 - Q474 Q709 Q711 - Q716 Q717 - Q724 Q759 Q761 - Q766 Q747 - Q474 QT01 Q601 Q603.
24 23 PP16 QY62 QN06 QN05 QN02 QN01 QN43 QN42 QN04 QY63 QY64 QY65 QN23 QN22 QN21 QN33 QN32 QN31 QY61 Q852 Q856 Q853 Q857 Q851 Q855 Q831 PY16 QY05 QY01 Q903 Q907 Q901 Q905 Q909 Q913 Q941 Q942 Q911 Q915.
25 26 QF01 Q153 Q123 Q159 Q160 Q157 Q156 Q136 Q135 Q134 Q137 Q139 QF02 Q121 Q110 Q132 Q133 Q102 Q101 Q108 Q107 Q124 Q103 Q104 Q109 Q111 Q112 Q115 Q106 Q138 Q125 PV16 Q105 Q117 Q116 Q119 Q118 Q113 Q114.
28 27 Pin Description Pin No Symbol I/O Description 1 D VDD0 — Digital power supply . 2 XRST I System reset. Reset when low . 3 MUTE I Mute input (low: off, high: on) 4 DA T A I Serial data input from CPU. 5 XLA T I Latch input from CPU . Serial data is latched at the falling edge.
29 Q126 : TC74VHC157 Inputs Output STB SEL A B H X X X L L L L X L L L H X H L H X L L L H X H H H : High L : Low X : 13 14 11 12 15 16 9 10 V CC 4A STB 4B 4Y 3A 1 2 3 4 5 6 7 8 SEL 1A 1B 1Y 2A 2B 2Y .
30 Q101 : CXD1881R Pin Description P ower Supply Pins Name T ype Descr iption VP A — P ower supply pin f or the RF block and serial por t VPB — P ower supply pin f or the ser vo b lock VNA — Gro.
31 Analog Pins Name T ype Descr iption BYP — The RF AGC integ ration capacitor CBYP , is connected between BYP and VP A. CP — DIFFERENTIAL PHASE TRACKING LPF PIN: The external capacitance is connected between CN. CN — DIFFERENTIAL PHASE TRACKING LPF PIN: The external capacitance is connected between CP .
32 Pin Symbol I/O Description No. 1 VSC — Core GND . 2 XMSLA T I Latch input for microcomputer serial communication. The address and data are atched at the f all of this pin. 3 MSCK I Shift clock input f or microcomputer ser ial communication. The serial input data is loaded and shifted at the rise of the clock input to this pin.
33 61 PHREFI I Phase reference signal input f or DSD output phase modulation. 62 PHREFO O Phase reference signal output f or DSD output phase modulation. 63 ZDFL O Lch zero data detection fl ag (when set by the microcomputer). Goes high when silent data continues f or 300ms.
34 126 WARFI Ai Analog RF signal input for PSP ph ysical disc mark detection. The full scale is 0.0 to 2.5V . (typ .) 127 WA VRB Ai A/D bottom reference f or PSP physical disc mark detection. The v oltage input to this pin is set to bottom lev el of the A/D conv er ter .
35 WA R F I W A D [7:0] WC K DQ [ 7 : 0 ] A[ 1 1 : 0] DC L K DCK E XWE XCAS XRAS S D [7:0] XSH D XSAK SDE F XSR Q A/D PSP Data Detection DST Decoder Fader Supplementary Data Interface Audio Interface .
36 Q124 : CXD1882R Pin Description The pin descriptions by function are given belo w . 1. Read Channel Block (22 pins) 1-1. PLL (8 pins) (1) PDHVCC (VC input for PD Hi-Z output) Midpoint potential input for RFPLL.
37 5. Host Interface (31 pins) Pin symbols are listed in the order of A T API mode, DMA mode and A V mode. Pull up means that the pin should be pulled up by a resistor , “0” means low lev el output, and nc means No Connect. (1) HCS0 (HOST chip select: input)/nc/nc This pin is pulled up by a resistor .
38 16 17 18 19 20 21 23 46 48 49 51 53 54 55 57 62 63 65 76 78 91 92 93 94 95 107 109 111 113 114 115 116 117 120 121 124 125 126 127 130 131 132 135 136 137 138 140 142 144 146 147 148 150 151 153 15.
39 Q125 : GXPQ7100(MASK) Pin No . Pin Name I/O Description 1 FTMUT O Actuator driver mute signal f or foc/trac k 2 SLMUT O Actuator driver mute signal f or spin/sledg 3 AMUT O Muting on/off "L&qu.
40 SCLK MCLK M4 LRCK SDAT A AOUTL+ AOUTR+ SERIAL INTERFACE AND FORMAT SELECT INTERPOLATION SOFT MU TE ∆Σ MODULATOR DYNAMIC DE-EMPHASIS SWITCHED AOUTL- AOUTR- FILT + FIL TER INTERPOLATION FIL TER FI.
41 QD41/QD61/QD71 : CS4397 Reset - RST Pin 1, Input Function: The de vice enters a low power mode and all internal state machines registers are reset when low .
42 Analog Ground - A GND Pins 18 and 21, Inputs Function: Analog g round ref erence. Differential Analog Outpus - A OUTR- , A OUTR+ and A OUTL- , A OUTL+ Pins 19, 20, 23 and 24, Outputs Function: The full scale diff erential analog output level is specifi ed in the Analog Characteristics specifi cations table.
43 44 QF01 : MB90F553A Pin P or t Signal I/O Function Descr iption Active 1 P20/A16 M41 O D A C select F ront L/R Active H 2 P21/A17 M42 O D A C select Surround L/R Active H 3 P22/A18 M43 O D A C select center ,LFE Active H 4 P23/A19 5 P24/A20 MUTE1 O MUTE F ront L/R Active H 6 P25/A21 MUTE2 O MUTE Surr .
46 45 9. EXPLODED VIEW AND P ARTS LIST (0 0 3 B ) ( 5128) 3X 6( M ) x2 001B F R O N T PAN EL ASSY. ( 003B ) 5110 3X 6( M ) x2 (5 1 2 8 ) 3X 6 ( M ) x2 024 B 012 G 013G ( 006B ) x3 (0 0 9 B ) x2 ( 002B.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 47 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 48 10. MECHA LO ADER ASS'Y NO VERS. COLOR P ART NO .
49 11. ELECTRICAL PARTS LIST The suppliers and their type n umbers of fusible resistors are as f ollows; 1. K O A Cor poration P ar t No. (MJI) T ype No .
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 50 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 51 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 52 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) Q719 HT109702A0 TRS.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 53 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) C852 OB47803520 ELECT.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 54 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) C114 EY10601620 TANTL.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 55 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) C260 EY10700620 TANTL.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 56 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO. (MJI) R158 nsp CHIP 1.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 57 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO.
NO TE : "nsp" P AR T IS LISTED FOR REFERENCE ONL Y , MARANTZ WILL NOT SUPPL Y THESE P AR TS. 58 POS. NO VERS. COLOR PART NO. (FOR EUR) DESCRIPTION PART NO.
An important point after buying a device Marantz SA-17S1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Marantz SA-17S1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Marantz SA-17S1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Marantz SA-17S1 you will learn all the available features of the product, as well as information on its operation. The information that you get Marantz SA-17S1 will certainly help you make a decision on the purchase.
If you already are a holder of Marantz SA-17S1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Marantz SA-17S1.
However, one of the most important roles played by the user manual is to help in solving problems with Marantz SA-17S1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Marantz SA-17S1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
