Instruction/ maintenance manual of the product Pruner E System Mantis
Go to page of 18
© 2006 Mantis, Div . of Schiller -Pfeiffer Inc. All Rights Reserved. © 2006 Mantis, Division de Schiller Pfeiffer Inc. T ous dr oits réservés. © 2006 Mantis, Division von Schiller Pfeiffer Inc.
1 T able of contents Important inf ormation A. Introduction This attachment is designed for trimming light to medium size branches. B. Pruner attachment specif ication. C. Contents of the package 1. Pruner attachment assembly with plastic gear case cov er 2.
2 Safety and warnings A. Safety labels Please pay particular attention to the warning and information labels found on va rious parts of this pruner attachment unit. They are an important part of the safety system. These labels must be replaced in time due to abrasion, etc.
3 General safety rules 1. Remov e branches in sections. Maintain safe operating positions, to av oid risk of being struck by falling branches or by those that rebound after hitting the ground 2. Cov er saw chain with guard during transport and storage.
4 Extension cord chart ( minimum cord gauge (A WG) 17. Sta y aler t . W atch what you are doing. Use common sense. Do not operate tool when you are tired, ill or under the influence of alcohol or other drugs.
5 1. Unscrew the mounting nut from the gear case co ver . Open the cov er . (Picture 3) 2. Mount the chain guide. Be sure that threaded pin fits into the opening in the guide bar . (Picture 4) 3. Fit the saw chain into the groo ve in the chain guide bar , and around the sprocket.
6 1. Loosen mounting nut and adjust the chain tension by turning the tensioner screw 2. Hold unit vertically , and tighten mounting nut 3. Mov e saw chain backwards on guide bar by hand. Sa w chain should mov e freely on guide bar if it is in proper mesh with the sprocket.
7 Check the balance of the assembled unit. The handles and shoulder harness hav e been assembled at the factory and set according to the av erage size person. This can be adjusted to the operator’ s preference by simple loosening the screws and sliding handles up or down the shaft.
8 Service maintenance guide Area Maintenance procedure Frequency Spline male/female connection of the inner driv e shaft Lubricate 20-25 hrs Gear case Use a grease gun to insert lubricant into the grease nipple of the gear case. Use EP2 lithium grease 20-25 hrs Guide bar Inspect/clean/replace The guide bar opening should be always a square.
9 Area Maintenance procedure Frequency Oiling port Inspect/clean Before each use Nose sprocket Clean/lubricate Before each use Saw chain Inspect/clean/sharpen/lubricate/replace Before each use Screws/.
10 • A Lo w-kickback Chain • Lo w-vibration Chain • Narro w-kerf Chain FILING TOOLS FOR FILING Saw chain sharpening pr ocedur e Square-gr ound Filing WHO SHOULD PERFORM SQU ARE-GR OUND FILING? Most chain saw users will probably ne ver need to use square ground chain, nor learn to perform square ground filing.
11 GULLET FILING Approximately ev ery 5th sharpening, clean out gullets with a 7/32" round file. File gullets from the inside out (the side opposite from sharpening). Leav e a 1/8 inch (3.175 mm) shelf behind the gullet. The depth-gauge setting for all square-ground chisel chain is .
12 48 48 2 2 4 4 3 3 6 6 5 5 8 8 7 7 9 9 5 5 12 12 13 13 1 1 1 1 14 14 15 15 16 16 17 17 16 16 18 18 19 19 20 20 21 21 22 22 23 23 25 25 24 24 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33 33 34 34 36 .
KEY # DESCRIPTION P ART # QTY 1 GEAR CASE CO VER 3331100 1 2 BEARING 6001-2Z 331101 1 3 GEAR CASE 331102 1 4 BEARING 627 331103 1 5 BOL T M5X12 331500 5 6 GREASE FITTING 331104 1 7 SCREW , TENSIONER 3.
Specifications, descriptions, and illustrati ve material in this literature are as accurate as kno wn at the time of publication, but are subject to change without notice.
DE Wir erklären in alleiniger Verantwortung, dass die elektrische 230-V-, 50-Hz-E-System-Astsäge mit einer installierten Nettoleistung von 0,95 kW: FR Nous, déclarons sous notre seule responsabilit.
DE FR GB NL ES IT SE DK NO FI Modell Modèle Model Model Modelo Modello Modell Model Modell Malli 330112/ 330106 Schalldruckpegel an Bedienerposition dB (A) Pression sonore au poste de l’opérateur .
P/N 331706 7/06 REV B MANTIS 1028 Str eet Road Southampton , P A 18966 + (215) 355-9700.
An important point after buying a device Mantis Pruner E System (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Mantis Pruner E System yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Mantis Pruner E System - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Mantis Pruner E System you will learn all the available features of the product, as well as information on its operation. The information that you get Mantis Pruner E System will certainly help you make a decision on the purchase.
If you already are a holder of Mantis Pruner E System, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Mantis Pruner E System.
However, one of the most important roles played by the user manual is to help in solving problems with Mantis Pruner E System. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Mantis Pruner E System along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
