Instruction/ maintenance manual of the product RP0900 Makita
Go to page of 28
1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES DOUBLE INSULA T ION DOUBLE ISOLA T ION DOBLE AISLAMIENT O W ARNING: For your personal safety , READ and UNDERST AND before using. SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE. A VERTISSEMENT : Pour votre propre sécurité, prière de lire attentivement avant l'utilisation.
2 ENGLISH SPECIFICA TIONS Model RP0900 Collet chuck capacity 1/4" Plunge capacity 0 - 35 mm (0 - 1- 3/8") No load speed (R PM) 27,000/min. Overall heig ht 217 mm (8-17/3 2") Net weight 2.
3 Power tool use and care 16. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for wh ich it was design ed. 17. Do not use t he power t ool if the sw itch does not turn it on and off.
4 9. Make sure the bit is not cont acting the workpiece before the switch is turned on. 10. Before using the tool on an actual workpiece, let it ru n for a while. W atch for v ibration or wobbling that could indicate improperl y insta lled bit. 11 . Be careful of the bit rotating direction and the feed direction.
5 CAUTION : • Since excessiv e cutting may cause overload of the motor or diffi culty in controlling the tool, the de pth of cut should not be more than 15 m m (9/16") at a pass when cutting grooves with an 8 mm (5/16") diameter bit.
6 CAUTION : • Install the bit securely . Always use only the wrenches provided with the tool. A loose or overtightened bit ca n be dangerous. • Do not tigh ten the co llet nut without i nserti ng a bit. It can lead to brea kage of the collet cone.
7 A 009751 T e mplet guide (Accessor y) 009752 The templet guide prov ides a sleeve through w hich the bit passes, allow ing use of the tool with temple t patterns. T o install the templet g uide, loosen the screw s on the tool base, insert th e templet guide and then tighten the screws.
8 009755 MAINTENANCE CAUTION : • Always be sure th at the tool is switched of f and unplugged before attempting to perform inspec tion or maintenance.
9 FRANÇAIS SPÉCIFICA TIONS Modèle RP0900 Capacité du mandrin à b ague 1/ 4" Capacité d'ins ertion 0 - 35 mm (0 - 1- 3/8") Vitesse à v ide (T/MIN) 27,000/min.
10 11 . Prévenez tout démarrage acc identel. Assurez-vous que l'interrupteur est en position d'arrêt avant de brancher l'outil. Vous ouvrez la porte aux accident s si vous transportez les outils électri ques avec le doigt sur l'interrupteur ou les bran chez alors que l'interrupteur est en position de marche.
11 Tableau 1. Gabarit minimum du cordon Intensit é nominale Volts Longueur totale du cordon en pieds 120 V 25 pi 50 pi 100 pi 150 pi Plus de Pas plus de Calibre am é ricain des fils 0 6 18 16 16 14 .
12 USD201-2 Symboles Les symboles ut ilisés pour l'outil son t indiqués ci-dessous. ･ volts ･ ampères ･ hertz ･ courant alternati f ･ vitesse à vide ･ construction, ca tégorie II.
13 La butée est munie de trois b oulons de réglage hexagonaux qui s'élèv ent ou s'abaissent de 0,8 mm (environ 1/32") p ar rotation . Vou s pouvez fa cilement obtenir trois dif férentes profondeurs de coupe sans modifier le réglage de la tige d'arrêt.
14 UTILISA TION Placez la base de l'outil sur la piè ce à couper sans que la fraise ne touche quoi que ce soit. Mettez ensuite l'outil sous tension e t attendez que la frai se ait atteint sa pleine vitesse.
15 Guide de gabarit (acce ssoire) 009752 Le guide de gabarit présente un m anchon à travers lequel passe la fraise, permettan t d'utiliser l'outil pour la reproduction exacte d'un mod èle donné. Pour installer le guide de gabari t, desserrez les vis à tê te plate de la base , insérez l e guide, puis resser rez les vis.
16 ENTRETIEN AT T E N T I O N : • Assurez-vous toujours que l'outil est hors ten sion et débranché avant d'y effectuer tout travail d'inspection ou d'e ntretien.
17 ESP AÑOL ESPECIFICACIONES Modelo RP0900 Especificaciones el éctricas en Méxi co 120 V 8 A 50/60 Hz Capacidad del ajustador del mandr il 6,3 mm (1/4") Capacidad de inserción 0 - 35 mm (0 - 1- 3/8") Revoluciones p or minuto (r .
18 10. Utilice equipos de seguridad. Póngase siempre protección p ara los ojos. El equipo de seguridad tal com o máscara contra el polvo, zapatos de seguridad antiderrap antes, casco rígido y prote cción para o ídos utilizado en l as condiciones apropiadas reducirá el riesgo de sufrir heridas perso nales.
19 Tabla 1. Calibre m í nimo para el cable Volts Longitud total del cable en metros 120 V~ 7,6 m (25 ft) 15,2 m (50 ft) 30,4 m (100 ft) 45,7 m (150 ft) M á s de No m á s de Calibre del cable (AWG) .
20 resultar en les iones personales graves. USD201-2 Símbolos A continuación se muestran los símbolos utilizados para la herramienta. ･ volts o v oltios ･ amperes o amperios ･ hertz ･ corri.
21 Bloque de tope 1 2 3 4 5 009746 El bloque de to pe cuenta con tres pernos hexagonales de ajuste los cuales se elevan o se bajan 0,8 mm (1/32" aprox.) por giro. Puede fá cilmente obtener tres profundidades disti ntas de corte al u sar estos pernos hexagonales de ajuste sin tener que reajusta r la vara de tope.
22 Inst alación o ex tracción de la fresa 009748 PRECAUCIÓN: • Coloque la broca firmemente . Utilice siempre la s llaves incluidas con la herramienta. Una fresa floja o apretada en ex ceso puede ser peligrosa. • No apriete la tuerca ajust adora sin insert ar una broca.
23 si el costado de la pieza de trabajo no es recto, la gu ía recta no puede usarse. En este caso, sujete un tablero recto a la pieza de trabaj o con la abrazadera y úselo como una guía contra la base de la rebajadora. Alimente la herramienta haci a la dirección de la flecha.
24 009755 MANTENIMIENTO PRECAUCIÓN: • Asegúrese siempre que la herramienta e sté apagada y descone ctada antes de inte ntar realizar una inspección o mantenimiento.
25.
26.
27.
28 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
An important point after buying a device Makita RP0900 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita RP0900 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita RP0900 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita RP0900 you will learn all the available features of the product, as well as information on its operation. The information that you get Makita RP0900 will certainly help you make a decision on the purchase.
If you already are a holder of Makita RP0900, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita RP0900.
However, one of the most important roles played by the user manual is to help in solving problems with Makita RP0900. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita RP0900 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
