Instruction/ maintenance manual of the product RBC25A Makita
Go to page of 16
String Trimmer Model RBC221 RBC251 Models: RBC221 RBC251 RBC25A RBC25A INSTRUCTION MANUAL Dimensions (mm) Weight (kg) Gear ratio Clutch Drive Shaft Type Engine: (L x W x H) Revolution of cutter head (.
Thank you very much for purchasing your MAKITA STRING TRIMMER. We are proud of and very confident in recommending our MAKITA STRING TRIMMER as a result of our extensive development and substantial knowledge and experience.
23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. Use only replacement parts that are identical to original equipment parts when servicing the unit: these parts are available from your dealer.
EQUIPMENT DESCRIPTION 4.
ASSEMBLY INSTRUCTIONS Mounting the handle (Fig. 1) 1. Attach the handle to the drive shaft. 2. Install the handle joint on the handle as shown in Fig. 1. 3. Insert the installation bolt M6x45 through the holes in the handle, and attach the flange nut M6.
PREPARING FOR OPERATION Fuel and oil mixture Inspect the fuel tank and fill with clean, fresh fuel of the proper mixture to assure the longer life of the tool.
ENGINE STARTING AND STOPPING PROCEDURES Starting when the engine is cold Use the following procedure when the engine is cold, or after it has been stopped for longer than 5 minutes, or after fuel has been added to the engine: 1. Slide the stop switch away from the "STOP" position (Fig.
CORRECT HANDLING OF THE MACHINE . Fig. 9 Fig. 10 I I Attachment, adjustment and detachment of the shoulder strap Attachment Place the strap hook into the hanger which is located on the shaft between the grip and the handle. Adjustment Adjust the strap length so that the nylon cutting head will be kept parallel to the ground (Fig.
DAILY CHECK-UP AND MAINTENANCE cover r cleaner case cleaner cover I Sponge element Fig. 12 Fig. 13 0.6 mm - 0.7 mm (0.024" - 0.028") 1. 2. 3. 4. 5. 6. 7. a. 9. 10. 11. Fig. 14 I Fig. 15 Before operation, pay particular attention to the tightness of the nylon cutting head.
STORAGE When storing the machine for a long time, drain the fuel from the fuel tank and carburetor as foll,ows: 1. Drain all fuel from the fuel tank. Gently push on the primer pump repeatedly until all fuel is expelled out of the primer pump. Properly dispose of the fuel in accordance with all local laws.
INSTRUCTIONS FOR USE OF THE NYLON CUTTING HEAD (BUMP & FEED BF4) Safety Instructions 1. Read this section carefully and thoroughly before use. 2. Check the nylon cutting head carefully before each use. If you notice any of following, replace the worn or damaged parts with new ones immediately (Fig.
Replacing the nylon cord 1. 2. 3. 4. 5. 6. 7. Press the housing latches inward to lift off the cover; then remove the spool (Fig. 23). Run the new nylon cord through the hole in the center of the spool, and pass one end of the cord through the notch into the other side of the spool.
Emission Control Warranty Statement YOUR WARRANTY RIGHTS AND OBLIGATIONS The California Air Resources Board and Makita U.S.A., Inc. are pleased to explain the emission control warranty on your 1995 and later utility and/or lawn and garden equipment engine.
LIMITED WARRANTY - California Only - Makita U.S.A., Inc., a distributor of utility and lawn and garden equipment in the U.S., warrants to the owner of 1995 and later utility and/or lawn and ga'rd.
WHAT IS NOT COVERED UNDER THIS WARRANTY This warranty does not cover any emission-related part which malfunctions, fails, or is damaged due to alter- ations and/or modifications such as changing, adding, or removing parts. When an engine is being serviced under warranty, Makita U.
REPAIR AND REPLACEMENT OF EMISSION-RELATED PARTS It is recommended that only engine replacement parts which have been authorized and approved by Makita U.S.A., Inc. should be used in the performance of any warranty maintenance or repairs of emission-related parts.
An important point after buying a device Makita RBC25A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita RBC25A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita RBC25A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita RBC25A you will learn all the available features of the product, as well as information on its operation. The information that you get Makita RBC25A will certainly help you make a decision on the purchase.
If you already are a holder of Makita RBC25A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita RBC25A.
However, one of the most important roles played by the user manual is to help in solving problems with Makita RBC25A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita RBC25A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
