Instruction/ maintenance manual of the product PLANER 2040 Makita
Go to page of 20
Planer 1 mm 11/32") of stock wtdth over 304 mmll 1-314") 3 mm 1118"l of stock width under 150 mm 15-718") Max. srock height No load speed 12.7 mm - 195mm 6,500 ,,,, In, 1112" - 7-518") 400 mm (15-3/4") MODEL 2040 2 9 m/mm 129 5 ftimin.
For Your Own Safety Read Instruction Manual Before Operating Planer GENERAL SAFETY PRECAUTIONS (For All Tools) 1. KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar to it.
Ampere Rating Not More Than More Than 0 6 6 10 10 12 12 16 Volts 12OV 25ft. 50ft. 100ft. 150 ft. 240V 5011. 100 ft. 200 ft. 300 ft. Total length of cord in feet AWG 18 16 16 14 18 16 14 12 16 16 14 12 14 12 Not Recommende 'Only the applicable parts of the Table need to be included.
3LTAGE WARNING: Before connecting the tool to a power source (receptacle, Itlet, etc.) be sure the voltage supplied is the same as that specified on the meplate of the tool. A power source with voltage greater than that specified )r the tool can result in SERIOUS INJURY to the user - as well as damage to le tool.
. . .. ,. . .. ... .I... , . .. . . .. , .. .. ... . ?. ::i 5. .. ., . . . "I .i'. . . .. . . . ...... . :: (;;!.. . ..: ... . .. ... . . . .. . ADDITIONAL SAFETY RULES 1. Wear eye protection. 2. Never perform planing operation with drive guard removed.
Dimensional adjustment Release the thumb screw on the stopper ring and turn the crank handle to the clockwise, aligning the indicator plate until the scale bar graduation for the desired finished dimension is reached. Algin your workpiece with the top of the table.
-~ ~ Return Returning cut stock back to the front side is very easy if you use the convenient re- turn rollers on top. Return rollers Stopper regulating depth Numerous workpieces can be planed to the same thickness very simply just by setting the stopper ring to the desired dimension.
CHANGING CUTTER KNIVES First, unplug the planer from the power source so as to prevent any mishap. Removal a. Loosen the pan hd. screws on the set plates with the (+) screwdriver, then swing the set plates.
CUTTER KNIFE INSTALLATION & HEIGHT ADJUSTMENT a. At the position shown in Fig. 7, insert the knife so the holes are aligned with those on the drum. Set the wooden levellers on each end of the knife edge and press down on both ends until the main frame surface is contacted.
ADJUSTING VARIOUS COMPONENTS Bed roller adjustment (The planer is factory-adjusted. If you notice the adjustment is off, kindly do as f 01 I ows.) Loosen the pan head screw for each roller under the table. Use a screwdriver to rotate the groove on the roller adjuster within 180 degrees on the four roller axes.
Extension roller adjustment Gently loosen the hex bolts, set a rule or yardstick on the table surface and adjust so that roller arm is slightly higher than the table. Tighten the hex bolts securely so that the roller arm surface is at the 90" to the column.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes 3emove and check the carbon brushes egularly. Replace when they wear down o the limit mark.
Lubrication (Periodic) Oil the chain (after removing the chain cover), the column moving parts (contact areas) and the crank handle. The periodic lubrication should be per- formed with machine oil.
ACCESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments hsould be used only in the proper and intended manner.
Mpy 12 '86 US 400 mm (15-3/4") I PLANER Model 2040 15.
MODEL 2040 c Jan -08-'96 Us c 16.
17.
MODEL 2040 I:.'," DESCRIPTION May 12-'86 US $f, DESCRIPTION MACHINE I 2 3 5 7 8 9 10 It 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 4.
MODEL 2040 Jan -08--'96 US ED DESCRlPTlDN MACHINE __ 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 I64 165 166 167 1 1 1 2 1 1 I 1 2 2 2 2 1 I 1 1 2 1 2 I 1 Hex Nul MB Spring Washer 8 Flat Warher 8 Pm Herd Screw M6.18 IWllh Washer1 Trnrlon mate Cap Square NeLk Bolt Max35 Motor Housing Rear Cover Pan Head Screw M5.
e MAKnA LIMITED ONE YEAR WARRANTY Warranty Policy Fvery Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted tu he free of defects from workanship and materials for the period of ONE YFAR from the date of orignal purchase.
An important point after buying a device Makita PLANER 2040 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita PLANER 2040 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita PLANER 2040 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita PLANER 2040 you will learn all the available features of the product, as well as information on its operation. The information that you get Makita PLANER 2040 will certainly help you make a decision on the purchase.
If you already are a holder of Makita PLANER 2040, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita PLANER 2040.
However, one of the most important roles played by the user manual is to help in solving problems with Makita PLANER 2040. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita PLANER 2040 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
