Instruction/ maintenance manual of the product LC1230 Makita
Go to page of 32
1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES DOUBLE INSULA T ION DOUBLE ISOLA T ION DOBLE AISLAMIENT O W ARNING: For your personal safety , READ and UNDERST AND before using. SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE. A VERTISSEMENT : Pour votre propre sécurité, prière de lire attentivement avant l'utilisation.
2 ENGLISH SPECIFICA TIONS Model LC1230 Blade diameter 305 mm (12") Hole (arbor) d iameter 25.4 mm (1" ) No load speed (RPM ) 1,300 /min. Dimensions (L x W x H) 516 mm x 306 m m x 603 mm (20-1/3" x 12" x 23-5/8") Net weight 19.
3 14. MAINT AIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow i nstructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories such as blades, bit s, cutters, and the like.
4 4. Do not perform any operation freehand. The workpiece must be secu red firmly against the base with a vise during a ll operations. Never use your hand to secure the w orkpiece. 5. Never reach around sa w blade. 6. T urn off tool and wait for sa w blade to stop before moving workpiece or changing settings.
5 FUNCTIONAL DESCRIPTION CAUTION : • Always be sure th at the tool is switched of f and unplugged before adjusting o r checkin g function on the tool. Switch action 1 2 003773 CAUTION : • Before plugging in the tool, alway s check to see that the switch trigger actuates properly and returns to th e "OFF" posi tion when released .
6 • Use only the Makit a socket wrench provided to install or remov e the blade. Failure to do so may result in overtighte ning or insufficien t tightening of the hex bolt. This could cause a per sonal injury . • Do not touch the bl ade immediately after operatio n; it may be extremely hot and could burn y our skin.
7 • T oo little pressure on the h andle may result in more sparks and premature blade w ear. • Do not touch the blade, w orkpiece or cutting chips immediately after operation; they may be extremely hot and could bur n your skin. • If the blade stops during operation, makes an odd noise or begins to v ibrate, switch of f the tool immediately .
8 Cutting rectangles Secure the workpiece in the v ise as shown in figure J, and proceed to cut it. Fig. J Fig. K 003784 CAUTION : • Do NOT cut the workpiece as show n in figure K since this may cause it to be ejecte d from the v ise, possibly resulting in injury .
9 Part No. A-90532 A-90722 A-90875 A-90847 Number of teeth application Applicable workpiece & thickness range Angles Pipes Channels Stainless Pipes Stainless Angles 60 Mild Steel 5/32" or mor.
10 FRANÇAIS SPÉCIFICA TIONS Modèle LC1230 Diamètre de la lame 305 m m (12") Diamètre de l'orif ice (alésage) 25.4 mm (1") Vitesse à v ide (T/MIN) 1,300 /min. Dimensions (L x L x H) 516 mm x 306 m m x 603 mm (20-1/3" x 12" x 23-5/8") Poids net 19.
11 chaussures antidérapantes est recommandé. Portez un filet de protection pour envelopper les cheveux longs. 11 . PORTEZ TOUJOURS DES LUNETTES DE SÉCURITÉ. Si le travail de coupe dégage de la poussière, portez également un écra n facial ou un masque antipoussières.
12 Tableau 1. Gabarit minimum du cordon Intensit é nominale Volts Longueur totale du cordon en pieds 120 V 25 pi 50 pi 100 pi 150 pi Plus de Pas plus de Calibre am é ricain des fils 0 6 18 16 16 14 .
13 22. Demeurez attentif en tout temps, et tout particulière ment lors des travaux répétitifs et monotones. Ne vous laissez pas emporter par un sentiment de sécurité trompeur . Les lames ne pardonnent p as. 23. Utilisez toujours les a ccessoires recommandés dans le présent manuel.
14 1 2 3 4 003774 Pour changer l'angle de coupe , desserrez le levier . Déplacez la butée de l'étau de sorte qu e l'indicateur pointe sur la graduation dé sirée. Serrez ensuite le lev ier pour immobiliser la butée de l'étau.
15 1 2 3 003778 Pour poser la lame, monte z le flasque intérieur , la lame, le flasque extérieur et le bouton hexagonal sur l'axe, dans cet ordre. Ser rez le boulon hexagonal en tournant vers la droite to ut en appuyant sur le blocage de l'arbre.
16 T enez la poignée fermement. Me ttez l'outil sous tension et attendez que la lame a tteigne sa pleine vitesse. Abaissez ensuite doucemen t la poignée pour approcher la lame de la pièce.
17 Fig. J Fig. K 003784 AT T E N T I O N : • NE P AS couper la pièce en procédan t comme à la figure K, car elle risquerait d'être éjectée de l'étau et de causer une blessure.
18 • Lame à dents d e carbure de tungstène • Les lames à dents de carbure de tung stène de 305 mm (12 po) et les dimension s de pièce permises N° de pièce A-90532 A-90722 A-90875 A-90847 No.
19 GARANTIE LIMITÉE D’UN AN MAKIT A Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial.
20 ESP AÑOL ESPECIFICACIONES Modelo LC1230 Especificaciones el éctricas en Méxi co 120 V 15 A 50/60 Hz Diámetro del disco 305 mm (12") Diámetro del orif icio (eje ) 25,4 mm (1") Revoluciones por minuto (r .
21 10. PÓNGASE INDUMENT ARIA APROPIADA. No se ponga ropa holgada, guantes, corbata, anillos, pulseras, ni otro tipo de alhajas que puedan engancharse en las p artes móviles. Se recomienda utilizar cal zado antiderrapante. Recójase el cabello o si lo tiene largo o cúbralo pa ra su protección.
22 Tabla 1. Calibre m í nimo para el cable Volts Longitud total del cable en metros 120 V~ 7,6 m (25 ft) 15,2 m (50 ft) 30,4 m (100 ft) 45,7 m (150 ft) M á s de No m á s de Calibre del cable (AWG) .
23 22. Esté alerta en todo momento, especia lmente durante las operaciones rep etitivas y monótonas. No se deje llevar por una falsa sensación de seguridad. Los discos no perdonan nunca. 23. Utilice los accesorios recomendados en este manual. La utilización de accesori os no apropiados, tales como discos abrasiv os, podría ocasionarle heridas.
24 1 2 3 4 003774 Para cambiar el ángulo de corte, afloje la palanca. Mueva el tope de la pren sa de modo ta l que el indicador señale la gradua ción deseada.
25 1 2 3 003778 Para instalar la hoja monte la brida in terior , la hoja de sierra, la brida exterior y el perno hexagonal en ese orden sobre el eje . Ajuste el pern o hexagonal girand o en el sentido de las ag ujas del reloj al tie mpo que presiona la traba.
26 Sostenga la empuñadura con firmeza. Encienda la herramienta y esp ere hasta que la hoja al cance plena velocidad. Luego baje la empuñadura suav emente para acercar la hoja a la pieza de trabajo.
27 Fig. J Fig. K 003784 PRECAUCIÓN: • NO corte la pieza de trabajo como se ilustra en la Figura K puesto que esto podría causar que saliera despedida de la pren sa, lo que probablemente ocasionaría heridas.
28 • Hoja de sierra con punta de carburo • Hoja de sierra con punt a de carburo de 305 mm (12") y rango de pie zas de trabajo Parte No. A-90532 A-90722 A-90875 A-90847 Número de dientes Apli.
29 GARANTÍA LIMIT ADA MAKIT A DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
30.
31.
32 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
An important point after buying a device Makita LC1230 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita LC1230 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita LC1230 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita LC1230 you will learn all the available features of the product, as well as information on its operation. The information that you get Makita LC1230 will certainly help you make a decision on the purchase.
If you already are a holder of Makita LC1230, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita LC1230.
However, one of the most important roles played by the user manual is to help in solving problems with Makita LC1230. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita LC1230 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
