Instruction/ maintenance manual of the product HM1203C Makita
Go to page of 28
1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES DOUBLE INSULA T ION DOUBLE ISOLA T ION DOBLE AISLAMIENT O Demolition Hammer Marteau de démolition Martillo Domoledor HM1213C HM1203C 009939 IMPORT ANT : Read Before Using. IMPORT ANT : Lire avant usage.
2 ENGLISH (Orig inal instruct ions) SPECIFICA TIONS Model HM1213C HM1203C Blows per minu te 950 - 1,900 Overall leng th 576 mm (22-3/4 ") Net weight 10.8 kg (23.6 lbs) 9.7 kg (21.4 lbs) • Due to our conti nuing program me of research an d development, th e specifications herein are subj ect to change w ithout notice.
3 ensure these are connected and properly used. Use of dust colle ction can reduce dust-related hazards. Power tool use and care 17. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for wh ich it was design ed.
4 loose easily , causi ng a breakdown or accident. Check tightness of screws carefully before operation. 7. In cold weather or when the tool has not been used for a long time, let the tool warm up for a while by operating it under no load. Thi s will loosen up the lubrication.
5 CAUTION : • The speed adjustin g dial can be turned only a s far as 5 and back to 1. Do not force i t past 5 o r 1, or the speed adjusting function may no lo nger work. For Model HM1213C only NOTE: • Blows at no load pe r minute becomes smaller than those on load in order to reduce vibration unde r no load, but this do es not show tro uble.
6 009941 After inst alling, always make su re that the bit is securely held in place by trying to pull it out. T o remove the bit, pull the releasing cover down all the way and pull the bit out. 1 009942 Bit angle 1 009943 009944 The bit can be secu red at 12 dif ferent angles.
7 1 009951 Disconnect the connector by pulling them. 1 2 3 009950 Loosen the four screw s on crank cap and remov e the crank cap cov er . 1 2 009952 Wipe out the old grease in side and replace with a fresh grease (60 g). U se only Makit a genuine hammer grease (optional accessory).
8 MAKIT A LIMITED ONE YEAR W ARRANTY W arranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory . It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
9 FRANÇAIS (Mode d’empl oi original) SPÉCIFICA TIONS Modèle HM1213C HM1203C Nombre de frappes par mi nute 950 - 1 900 Longueur tot ale 576 mm (22-3/4 ") Poids net 10,8 kg (23,6 lbs) 9,7 kg (.
10 résistante ou une protection d'orei lles. 12. Évitez les démarrages accidentels. Assurez-vous que l'interrupteur est en position d'arrêt avant de brancher l'outi l et/ou d'insérer la batterie, ainsi qu'avant de saisir ou de transporter l'outil.
11 Tableau 1. Gabarit minimum du cordon Intensit é nominale Volts Longueur totale du cordon en pieds 120 V 25 pi 50 pi 100 pi 150 pi Plus de Pas plus de Calibre am é ricain des fils 0 6 18 16 16 14 .
12 USD203-2 Symboles Les symboles ut ilisés pour l'outil son t indiqués ci-dessous. ･ volts ･ ampères ･ hertz ･ courant alternatif ･ construction, ca tégorie II ･ tours ou alterna.
13 Vo y a n t 1 2 009949 Le voyant vert de mise sous ten sion s'allume quand l'outil est branché. Si le v oyant ne s'allume pas, il y a peut-être un dy sfonctionnement sur le cordon d'alimentation secteur ou sur le contrôleur .
14 Angle d u foret 1 009943 009944 Il est possible de fixer le foret à 12 angles différents. Pour changer l'angle du foret, déplacez la bague d'orien tation vers l'avant, puis tournez la bague d'orientation pour modifier l'angle du foret.
15 1 2 009952 Essuyez la graisse usée à l'intérieur , puis remplacez-la par de la graisse fraîch e (60 g). Utilisez uniquement la graisse à marteau Makita aut hentique (accesso ire en option).
16 GARANTIE LIMITÉE D’UN AN MAKIT A Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial.
17 ESP AÑOL (Instrucciones originales) ESPECIFICACIONES Modelo HM1213C HM1203C Especificaciones el éctricas en México 120 V 14 A 50/60 Hz Golpes por minuto 950 - 1 900 Longitud tot al 576 mm (22-3/.
18 como resultado heridas personale s graves. 11 . Use equipo de protección personal. Póngase siempre protección p ara los ojos. El equipo protector ta l como má scara contra el po lvo, zapatos de seguridad antiderrap antes, casco rígido y prote cción para o ídos utilizado en l as condiciones apropiadas reducir á las heridas personales.
19 Tabla 1. Calibre m í nimo para el cable Volts Longitud total del cable en metros 120 V~ 7,6 m (25 ft) 15,2 m (50 ft) 30,4 m (100 ft) 45,7 m (150 ft) M á s de No m á s de Calibre del cable (AWG) .
20 USD203-2 Símbolos A continuación se muestran los símbolos utilizado s para la herramienta. ･ volts o v oltios ･ amperes o amperios ･ hertz ･ corriente alterna ･ Construcción clase II .
21 Luz indicadora 1 2 009949 La luz indicadora verde de su ministro eléctrico ("power-ON") se ilumina cuando la herramienta está conectada a la electricidad. Si la lu z indicadora no se ilumina, puede que hay a un defecto con el cable eléctrico o el controlador .
22 1 009942 Ángulo de la broca 1 009943 009944 La broca puede colocarse en 12 ángulos di ferentes. Para cambiar el ángulo de la b roca, deslice h acia adelante el anillo d e cambio y luego gírelo pa ra cambiar el ángulo de la broca. En el ángu lo deseado, desli ce hacia atrás el anillo de cambio hasta la posi ción original.
23 1 009951 Desconecte el con ector tirando de él . 1 2 3 009950 Afloje los cua tro tornillos sobre la t apa del cárter y retire la cubierta de la tap a del cárter . 1 2 009952 Limpie la grasa v ieja del interior y reemplácela con grasa nueva (60 g).
24 • Gafas de seguri dad • Lubricante p ara martillo • Maletín de tr ansporte de plás tico GARANTÍA LIMIT ADA MAKIT A DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica.
25.
26.
27.
28 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
An important point after buying a device Makita HM1203C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita HM1203C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita HM1203C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita HM1203C you will learn all the available features of the product, as well as information on its operation. The information that you get Makita HM1203C will certainly help you make a decision on the purchase.
If you already are a holder of Makita HM1203C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita HM1203C.
However, one of the most important roles played by the user manual is to help in solving problems with Makita HM1203C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita HM1203C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
