Instruction/ maintenance manual of the product HM0860C Makita
Go to page of 16
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.
2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions.
3 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts.
4 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to follo w Maintenance instructions may create a risk of electric shock or injury .
5 tion. Without proper warm-up, hammering operation is difficult. 7. Alwa ys be sure you have a firm f ooting. Be sure no one is below when using the tool in high locations. 8. Hold the tool firmly with both hands. 9. Keep hands awa y from moving parts.
6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the tool is s witched off.
7 Indicator lamp The green pow er-ON indicator lamp lights up when the tool is plugged. The indicator lamp is lit but the tool does not start e ven if the tool is s witched on, the carbon br ushes ma y be worn out, or the electr ic circuit or the motor ma y be defectiv e.
8 Inser t the bit into the tool. T ur n the bit and push it in until it engages. If the bit cannot be pushed in, remov e the bit. Pull the chuck cov er down a couple of times. Then insert the bit again. T urn the bit and push it in until it engages. After installing, alwa ys make sure that the bit is securely held in place by trying to pull it out.
9 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is e xposed to contact the commutator , it will automatically shut off the motor .
10 Lubrication This tool requires no hourly or daily lubr ication because it has a grease-pac ked lubrication system. It should be relubr i- cated after e very 6 months of operation. Send the complete tool to Makita A uthor ized Service Center for this lubrication ser vice .
11 Connect the terminal and reinstall the handle. CA UTION: • Be careful not to damage the terminal or lead wires especially when wiping out the old grease or installing the handle. • Whene ver reinstalling the handle, use the two short screws f or the upper side and two long screws f or the lower side .
Memo 12.
13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut.
14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2.
15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St.
W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm.
An important point after buying a device Makita HM0860C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita HM0860C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita HM0860C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita HM0860C you will learn all the available features of the product, as well as information on its operation. The information that you get Makita HM0860C will certainly help you make a decision on the purchase.
If you already are a holder of Makita HM0860C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita HM0860C.
However, one of the most important roles played by the user manual is to help in solving problems with Makita HM0860C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita HM0860C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
